Search Documents

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

By G. Chitiyo

Prediction of pothole characteristics is a challenging task, confronting production geologists at the platinum mines of the Bushveld Complex. The frequency, distribution, size, shape, severity and relationship (FDS3R) of potholes has a huge impact on mine planning and scheduling, and consequently cost. It is with this in mind that this study was initiated. Quantitative analysis of potholes indicates that pothole size (area covered) can be described by two partly overlapping lognormal distributions. These are referred to as Populations A (smaller) and B (larger). The range of observed pothole sizes conforms to a simple double exponential growth model based on Newton's Cooling Curve. A third size range of very large potholes (Population C) that could not be modelled properly within the proposed growth model is interpreted as to represent a very early phase of aggressive regional thermo-chemical erosion and potholing. In general, potholes are dominantly quasi circular with only a subordinate tendency of elongation. In the UG2, potholes with elongated forms are more prevalent in the size range between 20 and 500 m diameter. In the Merensky Reef elongated potholes are more common in the size range above 50 m in diameter. Although not distinctly visible, elongation of potholes in both the UG2 and the Merensky Reef show a net north/south orientation. Using shapes of pothole rims and floor areas, documented for the UG2 in the Waterval Shaft area, it is demonstrated that the northern, down-dip edges of potholes have steeper dips than the southern, up-dip edges. Spatial distribution studies using a uniform quadrant method suggest that in both the UG2 and the Merensky Reef, the potholes are randomly distributed, with a tendency towards clustering. Clustering appears to be more prevalent in the smaller Population A potholes. Bearing all findings in mind, it is found that the model of thermo-chemical erosion of the cumulus floor by new influxes of superheated magma best explains the observed data. Partial to complete melting of the cumulate floor occurred in three phases. The first represents the emplacement of hot magma. This magma, due to turbulent flow and high chemical and physical potential, aggressively attacks the existing floor (crystal mush on the magma/floor interface). Regional erosion is manifested by large, often coalescing potholes. During the second phase, when the magma emplacement process ceased and cooling in situ started, two distinct periods of pothole formation ensued. The first is related to rapid cooling along the relatively steep part of the Newton Cooling Curve, when Population B potholes nucleated randomly and grew rapidly with concurrent convective overturn and largely laminar flow condition. The second period of cooling occurred on the shallow-dipping part of the Newton Cooling Curve. Population A pothole growth became more subdued and nucleation appears to have been, at least locally, clustered. The final phase of this proposed 'super magma cycle' was introduced when chromitite crystallization and precipitation terminated pothole formation. This was followed sequentially by pyroxene and plagioclase crystallization to form the typical cyclic units of the Critical Zone. No suitable proxy could be found for the prediction of pothole density of potholes associated with the UG2 (likely due to limited spatial data coverage), and these are best predicted by extrapolation. The Merensky Reef slope index, in contrast, provides a proxy for pothole density, enabling prediction with reasonable confidence. This predictive model has been verified using underground information. The findings made during the course of this investigation have, when implemented, significant impact. Successful implementation will not only allow enhanced resource and reserve definition, but also better mine planning and scheduling.

Jan 1, 2008

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By M. Grave

Rock Engineers are required to design safe cost effective support systems and stoping layouts for their respective mines. As each stope has its own unique environment, continual re evaluation is required in all stopes to maximize extraction and achieve value from the support standard. This paper presents numerical modelling used to plan early mining within the shaft pillar and a reevaluation of an existing stope support standard.

Jan 1, 2009

By A. K. Verma

Several longwall faces in India have collapsed due to adverse geological conditions and/or inadequate capacity of powered supports. Thus it is imperative to access the capacity of a powered support and its interaction at longwall faces of varying geomining conditions in advance with lots of confidence. To achieve this, an index has been developed to ascertain the front leg pressure (FLP) of chock-shield support and roof-to-floor convergence (RFC) at longwall faces. The index called ?Longwall Face Stability Index? (LFSI) has been developed using statistics and Finite Element Modelling (FEM). The front leg pressure (FLP) and roof-to-floor convergence (RFC) predicted from the LFSI are validated with the field monitored data from two longwall panels. In this study, an attempt is also made to incorporate various geomining conditions into the finite element models typical of longwall mining practice. The index has taken into account the wide variations of geomining parameters like thickness, young?s modulus and friction angle of main roof (small, large), coal type (soft, hard), powered support capacity, and depth of coal seam. Thus, LFSI can be thought of as an index representing combined effect of roof type, geomining conditions and powered support capacity.

Jan 1, 2008

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By H. S. Sichel

"The valuation of diamond ferous deposits depends on (i) the density distribution, (ii) the size distribution of stones and (iii) the selling price structure prevailing at a particular time.In the density distribution the stochastic variable is defined as the Dumber of individual stones found per sample unit irrespective of the stone size. The density distribution is discrete and allows for barren sample units.As diamonds often occur in clusters, a Poisson mixture distribution is derived which is entirely new, as existing discrete distributions cannot represent the stone number frequencies found in nature.For the sizes of diamonds, which are measured by weight, a new compound logarithmic normal distribution is developed.Combination of (i), (H) and (iii) leads to a meaningful appraisal of diamond ferous ground expressed in monetary value per production unit of mining.Finally, confidence limits are calculated which allow for inference from sampling to recovery."

Jan 1, 2014

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By T. M. Russell

"Face mapping is a simple but invaluable means of geological and geotechnical data acquisition whereby intact rock properties, rock mass properties, discontinuity properties, and structural orientation can be assessed. Although traditionally done via direct contact with the mapping face through techniques such as line mapping or window mapping, remote face mapping using various digital techniques has become increasingly popular in recent years. Sishen is a large open pit mining operation requiring a comprehensive geotechnical data-set to evaluate pit wall design and stability with the necessary level of confidence. Geotechnical borehole data, face mapping data, geotechnical laboratory testing data, and implicit structural models provide the main sources of this information. Although a large geotechnical borehole database has always been maintained at the mine, face mapping has in the past been restricted to sporadic and isolated stability assessments. In 2013 the mine acquired a terrestrial laser scanner with the resolution, photographic capabilities, and software required to carry out geotechnical face mapping. A face mapping procedure was set up based on accepted face mapping methods, the data requirements of the mine, and capabilities of the laser scanner system. Mapping data obtained from the scans was integrated into the Acquire geological data management system, a purpose-designed structured query language (SQL) database system used for storing the mine’s geotechnical data. Within the geotechnical design process, having face mapping data available has improved confidence in the properties of the rock mass and structural environment, allowing for better definition of geotechnical design sectors. Overall, the face mapping and geotechnical analysis features of the terrestrial laser scanner in use make it an invaluable geotechnical data capture tool, provided a system is in place to store mapping data in a manner that allows for meaningful rock mass and structural information to be produced. IntroductionFundamental to the geotechnical design process is the acquisition of a reliable and complete geotechnical data-set. Geotechnical data acquisition will typically commence during the early stages of a project and continue well into the operational life of the mine, with the data confidence progressively increasing as the amount of data captured increases. Sishen mine currently bases all open pit geotechnical designs and geotechnical risk assessment on geotechnical borehole data in conjunction with interpreted structural models. Boreholes are logged and the data is captured in an ongoing process. This process forms the initial step in the geotechnical design and risk assessment process whereby the raw data is used to classify the strength properties for each lithology, provide inputs for geotechnical block models, and ultimately provide the inputs for slope design analyses. To date, borehole data has provided the only largescale, organized data-set for input into geotechnical analyses at Sishen. Although borehole data is the best and most comprehensive form of geotechnical data, there are some shortfalls that can be addressed by other data collection methods. These shortfalls are as follows."

Jan 1, 2018

By N. Mangesana

The effect of high solids concentration and coarse particle sizes (d50 ranges 90?300 µm) on the viscosity of a suspension of water and silica sand was investigated. The experiments were designed to include conditions that have been tested by other authors and those encountered in the operation of tumbling mills. The rheological data was measured using a tube rheometer with operating pseudo shear rates of up to 1500 s-1. The rheograms obtained depicted dilatant behaviour. The Otswald-de Waele, Bingham, Herschel-Buckley and Casson models were fitted to the experimental data. The Herschel-Buckely model, which approximates the yield point and gives an indication of the shear thinning or shear thickening behaviour of the suspension, was found to provide the best description of the flow curves for all slurries. The Herschel-Buckely model was then used to determine the apparent viscosity of all the tests. The apparent viscosity and yield stress increased with solids concentration and particle size at the different pseudo shear rates. The increase in slurry viscosity with solids concentration was attributed to increased frequency of particle-particle interactions. The increase in slurry viscosity with particle size was attributed to increased inertial effects. At low shear rates the sand slurry exhibited shear thinning behaviour for all solids concentrations. At higher shear rates above 1000 s-1the high solids concentration suspensions exhibited a transition from shear thinning to a shear thickening behaviour.

Jan 1, 2008

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By I. V. Filippova, Y. Foucaud, M. Badawi, O. Barrès, L. O. Filippov, S. Lebègue

Sodium silicate (Na2SiO3) is one of the most common reagents used in the froth flotation process, in which it is an efficient dispersant as well as a powerful gangue minerals depressant. Due to its high affinity with a lot of minerals, mostly silicates, it adsorbs on their surfaces and prevents the adsorption of the collectors, maintaining them hydrophilic. Hence, Na2SiO3 is widely used in the flotation separation of rare earth minerals, zinc minerals, iron minerals, scheelite, fluorite, apatite, and many other minerals. For decades, authors have demonstrated higher efficiency of Na2SiO3 when it is used in combination with sodium carbonate (Na2CO3), a common pH regulator. Among many well-known depressants, this system presented the best efficiency for many ores, including the Tabuaço scheelitebearing skarn studied herein. However, the mechanisms resulting in these strong positive synergistic effects are not well understood at the moment. Hence, the response surface methodology (RSM) was applied to this ore, considered as a case study, to optimize the depressing conditions and to study deeply the flotation behavior of this system. Strong synergistic effects between the two reagents were exhibited by the RSM, mostly affecting the scheelite, fluorite, and calcium-bearing silicates recoveries. This was attributed to surface carbonation of the minerals by Na2CO3, subsequently leading to a better depression by Na2SiO3. Overall, a 1:1 ratio between the two reagents displayed the best results in terms of WO3 grade and recovery. To gain understanding in the molecular mechanisms responsible for the aforementioned synergistic effects, FTIR studies were combined with state-of-the-art molecular modelling (Ab Initio Molecular Dynamics at 300 K) on fluorite, an archetype of calcium minerals. Keywords: Synergistic effects, scheelite, depressants, FTIR, DFT calculations

Jan 1, 2020

By J. U. Burger

The Elizabeth Bay aeolian deposit in Namibia comprises a sedimentary package of diamondiferous grits that have been deposited, reworked and concentrated to various degrees by dominant southerly winds. Diamond concentration in these deposits is highly variable and often unpredictable. The deposit is marginal from an economic perspective and therefore requires selective mining which in turn requires correct sampling and accurate estimation. Three methods of sampling have been used at Elizabeth Bay for mineral resource estimation: (i) pit samples utilizing an excavator to produce a sample 1 to 3 metres deep with a 10 to 20 m2 footprint, (ii)GB50 grab sampling with a 3.34 m2 footprint and (iii) a BG36 bucket auger drill with a 5 m2 footprint. Pit sampling, being easy to execute, has been the most widely used despite a limited penetration ability and, at times, questionable integrity. The GB50 grab sampling tool was tested at Elizabeth Bay and although it had better penetration ability and sample integrity, it struggled with cemented horizons. No sample optimization was conducted prior to the GB50 grab sampling. The latest phase of sampling was conducted using a BG36 bucket auger drill which is capable of penetrating thick overburden, penetrate cemented horizons and provides an acceptable sample support size. Geostatistical simulation methods were applied to establish the optimum sampling parameters required to estimate a mineral resource at an indicated level of confidence. The results show that a 5 m2 sample support size is adequate and that a 50 m 100 m sample configuration is optimal. Sample data obtained from the three methods confirms that the BG36 bucket auger tool combined with the parameters identified in this exercise produce the best results for diamond resource estimation.

Jan 1, 2009

The successful commissioning of the Cerro Verde project in Peru at the end of 2006 marked the culmination of the efforts of many in the industry over many years to have high pressure grinding roll technology recognized and accepted as a legitimate alternative to the conventional approach to large-scale hard rock comminution circuit design. Other hard-rock projects that have recently adopted HPGR include Freeport (Indonesia), Boddington (Australia) and Amplats Potgietersrus (South Africa). With the increasing acceptance of this technology, the need for technical presentations and articles exhorting the industry to adapt has diminished somewhat, and it is considered appropriate now to shift the emphasis to the provision of information for those considering embracing change. This article endeavours to answer frequently asked questions on the subject of high pressure grinding roll technology, with particular reference to its application in the hard rock minerals processing sector.

Jan 1, 2010

By N. D. Fernandes

Labour-intensive narrow reef stoping, as traditionally practised in South African gold and platinum mines, is almost unique in the modern first-world mechanized mining environment. Shortcomings of the system include the ever increasing cost of labour, a cap on achievable productivity and a poor safety record, particularly in the field of rock-related accidents. In the absence of sustainable alternative technologies, the South African mining industry has spent millions of rands improving the present system, focusing on improving workplace safety. This paper details the changes to stope support at Impala Platinum?s Rustenburg operations, and the impact on rock-related safety performance. Keywords Stope panel support, narrow reef stoping, improving workplace safety.

Jan 1, 2011

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

By A. Yañez, J. Yianatos, P. Vallejos, R. Grau

This paper presents an evaluation of the effect that the mineral feed characteristics have on the metallurgical performance in an industrial flotation circuit. Variables such as mineralogy, particle size, solid content and mineral grade were evaluated using a flotation simulator, which was previously developed and validated using industrial data from different concentrators. The metallurgical performance was evaluated not only from the point of view of recovery and concentrate grade, but also by analysing less common variables such as froth carrying rate, froth and collection recovery, water recovery and others. Then, new data from the industrial flotation circuit was used to complement this analysis and evaluate the simulator predictability by comparing simulated and measured data. The results allowed for the quantification of the significant effect that mineralogy and particle size have on recovery and/or concentrate grade. Therefore, the grinding stage and flotation cells design become important factors to avoid a significant loss in metallurgical performance when feed mineral characteristics change in an industrial operation. In this context, an evaluation of cells design and arrangement should be performed to compensate the loss in recovery and concentrate grade in order to find an optimal operating condition. Keywords: Flotation circuits, mineral feed, modelling, particle size, liberation, mineralogy

Jan 1, 2020

By D. Burrows

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007