Search Documents

By J. E. Chilton

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

Jan 1, 2003

By D. Bessinger, H. Kotzé, J. Beukes

Keywords: Pyrometallurgy, furnace, ilmenite, smelting, Ticor Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and Mineral Separation Plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2 slag and 145 kt/a of pig iron.

Jan 1, 2006

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By J. O. Marsden

The copper industry is cyclical with the price determined by market forces (i.e. the balance between supply and demand for the metal.) The period of each cycle typically varies between 6 to 9 years. These cycles drive decision making for exploration, new project and mine development, mine closures, process improvement, research and development, and technological innovation. The gold industry is fundamentally different from copper in that supply and demand do not, alone, determine metal price and many other factors play a key role, including global and regional financial conditions, political stability, and the global future economic outlook. However, the gold price experiences trends and longer term cycles that similarly drive business decision making. This paper examines developments in the copper industry that have occurred over the past few price cycles (approximately 20 years) and explores how the lessons learned can be applied to gold extraction. A number of specific examples and opportunities are discussed in detail, including; technology development and innovation, cost control and business improvement, material characterization, comminution equipment, biological heap leaching, and concentrate pressure leaching.

Jan 1, 2009

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005

This paper describes experimental investigations into the reductive decomposition of arsenopyrite/pyrite (FeAsS/FeS2), a gold and silver bearing iron/arsenic sulphide using metallic iron powder. The main objective was to establish and experimentally confirm the thermodynamic and kinetic feasibility of reductively decomposing the sulphide matrix for precious metals recovery. In this context, cyanidation leach tests were conducted on the reductive leach residues. The arsenopyrite/pyrite flotation concentrate, mainly studied in the hydrochloric acid medium, decomposed through the non?oxidative chemical dissolution reaction and the reductive decomposition reaction for the arsenopyrite and pyrite components, respectively. Desulphurization levels below 65% were achieved at pH values below 0.15 and iron to concentrate ratios above 1, and the system was characterized by overall very slow kinetics. The reaction system had a direct linear relationship with iron to concentrate ratio and an inverse relationship with pH. An analysis of the pyrite/iron galvanic system showed that pyrite forms a partially inert cathodic surface on which the anodic dissolution of iron occurs, supported by the hydrogen evolution reaction. This phenomenon explained the low desulphurization levels and the mineral decomposition seemed to be restricted to the non?oxidative chemical dissolution reaction for the arsenopyrite component. The cyanide leach of the reductive leach residues showed very little improvement in gold recovery. The reductive leach process for arsenopyrite/pyrite has considerable limitations in terms of both desulphurization and precious metals liberation. Keywords: Pyrite, arsenopyrite reductive leaching, hydrogen sulphide, invisible gold

Jan 1, 2009

By H. W. J. P. Neomagus, J. R. Bunt, D. L. Botha, N. T. Leokaoke

Coal briquetting traditionally makes use of high-dosage, nonpolymeric binders (such as coal tar pitch or molasses) or polyvinyl alcohol (PVA) at low dosages for the binding of fine and ultrafine coal. Due to constraints associated with the manufacturing and cost of PVA-bound briquettes, a novel polyacrylic binder was developed that could possibly be added in low dosages at room temperature. A set of formulations of two polyacrylic components (components A and B) was developed, from which an optimal binder mixture was determined. This formulation comprises 40wt.% component A and 10wt.% component B with a 0.04wt.% cross-linking additive, and the balance water. The uniaxial briquette compressive strength was used to obtain the optimal binder mixture. The binder mixture was added to the coal powder in dosages from 0.1 to 1.2wt.%. Mechanical tests and thermogravimetric analysis in an oxidized environment at a maximum temperature of 930°C were conducted. Binder-bound briquettes were compared to binderless briquettes and PVA-bound briquettes. Briquettes made from the polyacrylic formulation had uniaxial compressive strengths double that of the binderless briquette yield strength, as well as the minimum recommended compressive strength of 0.375 MPa. The organic binders did not affect the combustion of the briquettes, since the results compared well with the binderless briquettes. The polyacrylic formulation is considered to be a possible substitute for PVA in terms of mechanical and thermal properties and raw material cost.

Mar 1, 2021

By L. M. Tavares, H. A. Petit, P. P. Cavalcanti

Iron ore pellets experience degradation during handling due low energy impacts and stresses. These impacts lead to volume or surface breakage of the pellets, creating fine particles that accumulate along the process. Some of the particles are in contact with the air and are dragged as dust into the workplace or into the atmosphere. The aerodynamic size of the particles allows them to be potentially inhaled by the workers or to be carried to nearby communities. Dust emission becomes critical at specific locations, such as transfer chutes and stockpiles. This work models the dust generation that occurs in an iron ore pellet stockyard using a methodology that combines experiments to quantify the degradation of the pellets to mathematical modelling of the dust emission mechanisms in the stockyard. First, laboratory tests were used to characterise the amount of mass and the particle size distribution of the dust generated by degradation under controlled conditions. Second, the flow over a stockpile of an iron ore pellet company was simulated with the aid of computational fluid dynamics (CFD) simulations. Third, semiempirical equations linked the data generated by simulations and laboratory tests to estimate the dust emission in the stockyard. Finally, results were validated with measured field data, obtained with a novel online measurement tool. Results suggest that the approach is able to predict dust emission with sufficient accuracy and can be used for further implementation in the management of operations and decision making in order to reduce the environmental impact of the process. Keywords: Iron ore pellets, abrasion, dust emission, mathematical modelling

Jan 1, 2020

By A. Tello

Variography was introduced by Dr. Pierre Gy to monitor a process, in the sixties. Later on, Francis Pitard extended this concept, building a complete system of variographic controls for different applications. Nevertheless, the existence of information about its use as a way to effectively control plants has been limited. There are infinite areas where variography and chronostatistics can be used. In this paper, two different cases related to gold and silver recovery, through well known but complex metallurgical routes are studied. The use of effective management of process variability software (EMPV) has shown to be a suitable solution to clarify problems at the plant and, consequently, a solution to the encountered problems has been proposed. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in depth way. Once the ore has been extracted from the mine, sampling is necessary at each sequence of the metallurgical process involved. As a first example, leaching of the ore with cyanide in agitated tanks is another case of a complex metallurgy. The aim of the process is to know about residual values in the tailings in order to optimize process. As a second example, leaching of gold and silver in ore heaps, has to be optimized in terms of time, reagents consumption and, of course, in predicting a reasonable recovery. This last issue appears to be crucial. After cyanide leaching at the heaps, a carbon in columns process is involved, where there are a series of carbon loaded columns that are submitted to a dynamic process of load and unload, to finally deliver an enriched solution to the precious metal electrowinning plant. In both cases, variography has been a good approach to show metallurgists ways to improve the operation.

Jan 1, 2009

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023

By G. Mucsi, F. Kristály, R. Szabó

Kaolin is one of the most important ingredients in porcelain manufacturing. Its main phase is clay mineral containing aluminum hydrosilicate, namely kaolinite. Beside kaolinite it also contains quartz, illite and feldspars, which impair its applicability. Kaolin is a non-reactive material, but metakaolin can be produced by heat treatment (calcination) of kaolin, which is also used by the cement and concrete industry due to its latent hydraulic (pozzolanic) properties. Beside thermal activation, reactive materials can also be produced by mechanochemical activation in general. This paper deals with the mechanochemical activation of kaolin. The raw material was classified into various size fractions, then ground in a batch stirred media mill under varying circumstances (residence time, circumferential velocity). After grinding, the structural changes of the products were investigated by X-ray diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). In addition, the particle size distribution of the ground material was determined by laser scattering. As a result of the grinding experiments and analytical measurements of the products, it can be clearly seen that reactivity of kaolin can be improved significantly by mechanical activation in a stirred media mill, but due to its high energy density the circumstances were optimised carefully to avoid aggregation. Keywords: Kaolin, grinding, stirred media mill, mechanical activation, material structure

Jan 1, 2020

By G. Bueno, L. M. Tavares, T. M. Campos

Iron ore pellet feed pressing has been one of the first and most successful applications of High- Pressure Grinding Rolls (HPGR) in the minerals industry. Vale S.A. has been one of the pioneers in this application, currently with six HPGRs in operation in the pelletising plants of the Complexo de Tubarão (Brazil). In spite of the important advances in the technology, risks still exist when scaling-up the process from small-scale information. The present work takes advantage of the recent advances in the mathematical modelling of the HPGR performance, using the population balance model to evaluate the modified Torres and Casali model prediction in iron ore pellet feed pressing for different scales of operation. Results are presented that compare the HPGR performance in different operational scales for iron ore pellet feed pressing, demonstrating the confidence of this model-based approach for scale-up to full-scale HPGRs used in pressing iron ore concentrates. Keywords: Scale-up, HPGR, pellet feed, modelling, simulation

Jan 1, 2020

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By S. Andika, O. A. Putri

Maintaining fleet productivity, which consists of balancing loader and truck performance, has always been a challenging task. An automatic dispatching system (ADS) is implemented to help monitoring fleet condition and assign trucks to a designated loader. Integrated data from real time Global Positioning System, Vehicle Health Monitoring System, and other production related data are acquired to support the ADS. However, the abnormal truck cycle has been the main culprit which resulted in unnecessary loader hanging time and trucks queuing time. Hanging and queuing time accounted for 2.34 and 2.07 minutes respectively per loading cycle or equal to 2,861 loose cubic metres per fleet per day production losses. Using integrated dispatching system data, the authors conducted research to study a truck’s hauling cycle that affects fleet productivity. The data is modelled to obtain the arrival rate pattern in a front loading area by adopting the queue theory algorithm. This paper aims to understand the potential pattern of a truck’s cycle abnormality and to resolve its occurrence.

Sep 1, 2021

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By B. McFadzean, S. Pikinini, C. T. O’ Connor

Sperrylite (PtAs₂) comprises about 21% of the platinum group minerals (PGMs) in the Platreef ore and regularly reports to the tailings due to its poor floatability. Hence, improving its recovery will be of great economic value to the South African PGM industry. The reasons for its poor floatability are not yet clear. This paper seeks to understand the interactions occurring between PtAs₂ and common thiol collectors, viz. potassium normal butyl xanthate (PNBX), sodium normal dibutyl dithiophosphate (SNBDTP) and sodium normal mono butyl dithiocarbamate (SNBDTC). By understanding its interactions with these collectors, it is hypothesised that it will be possible to suggest ligands that may help improve the floatability of sperrylite. Mineral-collector interactions were studied by determining the molar energy of interaction using isothermal titration calorimetry and electrochemical techniques. The hydrophobicity of the mineral before and after adsorption of the collectors was determined by heat of immersion and its flotation response determined by microflotation tests. Microflotation tests using synthetic sperrylite at pH 9 showed low collectorless recovery of 34.8% and after adding the equivalent of one pseudo-monolayer of the PNBX collector, the recovery of 32.5% was obtained. Moreover, the addition of up to three pseudo-monolayers coverage of PNBX did not result in any increase in flotation recovery. A small recovery improvement was noted when synthetic plant water with the ionic strength of 0.0484 mol/L was used, but this did not hold for all collectors, with SNBDTP exhibiting higher recoveries in distilled water. Keywords: Sperrylite; flotation; recovery; adsorption energy; collectors; 2SPW (synthetic plant water)

Jan 1, 2020

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By A. O. Filmer

In the mining and metals industry, business strategy demands that leaders extract more from any set of capital assets. This improvement is achieved through a combination of continuous improvement and upgrading of the assets. Continuous Improvement involves a series of incremental changes in the workplace to stabilize the process, remove waste, and test the limits of process capability. Enhanced Technology involves the replacement of an existing as set with a different process or equipment, to achieve a similar function in a more efficient and effective manner. The paper compares and contrasts the two methodologies and outlines the key business considerations which dictate how and when to select one or other improvement method. The paper also addresses the implications for these two improvement methods for those undertaking R&D in support of the mining and metals business.

Jan 1, 2009

By G. A. Slabbert

The paper describes work undertaken to identify the influence of the matrix structure on the metal dusting rate of stainless steel alloys. Specifically, the difference in metal dusting rate between austenitic and ferritic stainless steels of similar chromium contents was investigated. The alloys were exposed to metal dusting conditions and their performance compared by weight loss, optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. The specific gas mixture used for all the tests were 18.9% CO-79.1% H2-2% H2O at 650°C. For austenitic stainless steels, Types 304, 321, 316, and 316Ti were compared to two ferritic grades, namely Types 430 and 441. The resistance of the ferritic grades was found to be significantly better than that of the austenitic grades. This was attributed to greater permeability of chromium through the matrix structure to maintain the protective oxide scale. The results will be used in the development of novel alloys to combat metal dusting.

Jan 1, 2013