Search Documents

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By A. R. Barnes, A. F. Newall

Keywords: Pyrometallurgy, furnace, smelting, spinel, PGM, phase diagrams As Merensky reef ores are replaced by UG2 ores, chromium levels in PGM smelting furnace feeds have steadily increased. Increased chromium levels lead to operating problems. Attempts to increase the chromium solubility in the slag by a variety of techniques create other difficulties. The authors have developed a technique for removal of the chromium spinel interface along with the matte for subsequent separation outside the smelting furnace by utilising differential solidification in the ladle. The process has been patented internationally with support from the Innovation Fund.

Jan 1, 2006

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

If you have problems or questions relating to the installation of this disc, please either telephone Document Transformation Technologies at (+27 12) 667 2074, or e-mail: nigel@doctech.co.za Si vous avez des problèmes relatifs àl?installation de ce disque, veuillez appeler Document Transformation Technologies au (+27 12) 667 2074, ou nous écrire par courrier électronique: nigel@doctech.co.za Produced by: / Produitpar:Document Transformation TechnologiesP O Box 560 ?Irene ?0062 ?South Africa.Tel: (012) 667 2074; Fax: (012) 667 2766; International Code (+27 12) e-mail: doctech@doctech.com website: http://www.doctech.co.za

Jan 1, 2004

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

The Fourth Industrial Revolution has driven significant advancements in autonomous robotic systems, particularly in subsea exploration and offshore mineral dredging. This review examines the latest developments in electrically powered quadrotor-track subsea robotic crawlers, highlighting their potential to enhance efficiency, mobility, and adaptability in challenging underwater environments. The integration of advanced automation, artificial intelligence, and real-time control systems has paved the way for more effective robotic solutions in offshore mining. This study explores the dynamic performance of hydraulic crawlers to quadrotortrack robotic dredgers, focusing on their propulsion, navigation, and stability under high hydrodynamic conditions. By leveraging state-of-the-art technologies such as lithium-ion battery power systems, intelligent microprocessors, and sensor-based control mechanisms, these robotic crawlers offer a promising alternative to conventional subsea excavation methods. Furthermore, the review analyses recent experimental and simulation-based studies that assess the feasibility and performance of these systems in real-world applications. The findings of this review provide valuable insights into the role of 4IR in transforming subsea robotics for offshore mineral dredging. By addressing existing limitations and identifying key technological advancements, this study contributes to the ongoing development of nextgeneration robotic systems capable of operating efficiently in extreme underwater conditions

Jan 30, 2026

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

"Investment in diamond exploration has been declining over the past decade, in spite of positive long-term industry fundamentals and a growing interest in diamonds as an investment category. The lack of new significant discoveries in recent years has eroded investor confidence, yet no new discoveries are possible without investment in exploration. Junior ‘mine finders’ have been the hardest hit. Their agility, tenacity, and appetite for risk are not sufficient to attract the funding required, even at the greenfield stage. Developing new discoveries into mineral resources can be crippling without solid financial support. Junior incubators could play a crucial role, especially at the project evaluation stage – but where are they? Alternatives to traditional funding mechanisms have become available, many still untested in the junior diamond exploration space. Valuable lessons can be drawn from the past and used to inform emerging new strategies. IntroductionDiamonds are the ultimate expression of love. Their ancient and timeless allure continues to influence consumer emotions and behaviours across continents, cultures and age groups. Analysts are predicting a sustained supplydemand shortfall in the years ahead which will trend diamond prices generally upwards. With positive long-term industry fundamentals, one cannot help but wonder why funding for diamond exploration and development projects is so scarce.Investment in exploration across commodities – including diamonds – has been declining for a number of years, reaching a historic eleven-year low early in 2017. The lack of major diamond discoveries in recent years has done little to strengthen the case for investing in diamond projects, yet no new discoveries can be made without investment in exploration.Global estimates of known carats in the ground stand currently at 2.5 billion carats, which equates to around 18 years of production at current levels of 140 million carats (mct) per annum. Sustainable replenishment of depleting diamond resources is possible only through the development of new discoveries. This is what junior explorers are best at – but they need investors to fund their evaluation activities from early in the project development continuum."

Feb 1, 2019

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

By R. J. Hundermark, L. R. Nelson

The critical importance of tap-hole design and management to furnace performance and longevity is explored through examining some of the specific matte, metal and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloys smelting and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally core aspects of tap-hole equipment and maintenance are identified that are considered important to securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance.

Jan 1, 2014

By N. Theron, R. F. Meeser

The global emphasis on conserving energy resources has led to the adoption of hybrid power systems in vehicles. Optimally applied, hybrid systems can save up to 40% on fuel costs. To optimally manage a hybrid vehicle's energy flow it is necessary to know, in real time, all the energy requirements to complete a given route. The energy consumption depends mainly on the vehicle mass, speed profile, and route topography. Of these, the topographic profile is the one factor that is only route-dependent and not influenced by the vehicle or driving styles. The heading vs. distance profile is also an example of a route characteristic not influenced by the vehicle or driving style. In this study the topographic and heading profiles are used to identify routes, and are easily measured by means of digital barometric pressure and compass sensors. Correlations between the current route and previously travelled/stored routes are performed based on their topographic and heading profiles in a point-by-point manner. Above-ground tests were first performed using a road vehicle and six routes to evaluate the system. The system consistently and correctly identified a 20 km route within the first 4 km. It also proved to function correctly in underground tests through the implementation of an instrumented hand-held surveyor's wheel. This system finds direct practical application in optimizing the energy management of an underground hybrid locomotive used by the mining industry in South Africa, but can also be of benefit in applications where route identification is required and using GPS is not feasible.

Jan 26, 2023

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By R. Kuyvenhoven, A. Parbhakar-Fox, X. Prieto, J. Quevedo, L. V. Danyushevsky

This paper presents the results of a study focussed on determining the distribution of cobalt in different types of pyrite of the La Estrella IOCG deposit in Chile. In the IOCG mineral deposits, where copper is the main product, the quantification and distribution of cobalt is required to correctly define the technical and economic viability of recovering cobalt as a by-product. In the La Estrella mineral deposit, seven alteration and mineralisation events were recognised through both optical and automated electronic mineralogical analysis. Of these seven events, five different types of pyrites were identified, each with unique characteristics of the pyrite crystals. Through advanced elemental analysis of these five types of pyrites, it was determined that the concentration and distribution of cobalt within the pyrite crystal is dependent on the mineralisation event. The results indicate high cobalt concentrations in the early pyrite mineralisation events, associated with relatively fine pyrite grains, and cobalt generally occurring in a solid form in the pyrite core. The late pyrite mineralisation event exhibits the lowest concentrations of cobalt, with cobalt predominantly present along the outer periphery of the pyrite. These results are relevant from a metallurgical point of view because the preferential location of cobalt within the pyrite crystal will influence the maximum metallurgical recovery of cobalt. For this, a cobaltiferous pyrite concentrate must be formed which, according to the characteristics of pyrite, must be processed with the optimal solubilisation method. The overall objective is to ensure both good cobalt recovery and a high concentration of cobalt in the leach solution resulting from pyrite leaching. Keywords: Cobalt, pyrite, IOCG, copper, metallurgical recovery, solubilisation, Chile

Jan 1, 2020

By P. W. J. van Rensburg

The Institute was privileged to receive an invitation from the Armaments Corporation of South Africa (Armscor) for members to visit one of their plants. As these are factories, the number of visitors who could be accommodated was limited. As the opportunity seldom arises to learn something of this very large industry, there was great interest among members and many were disappointed in not being able to go. Underwater mining The 16th Annual Underwater Mining Institute will be held at Halifax, Nova Scotia, Canada, from 20th to 23rd October, 1985.

Jan 1, 1985

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By C. Dauber

Implementing new technologies in industrial operations entails the challenge of measuring the improvements gained by the applied technology. Nevertheless, it is absolutely essential to assess the technical and economic benefits in objective and comprehensible numbers to create a platform for further management decisions. Underground coal mines are characterized by numerous, quite complex procedures which make it difficult to determine the specific economic benefit of a new machine, technique, or method. In the OPTI-MINE Project funded by the European Union?s RFCS programme, five underground coal mines applied the latest information and communication technologies (ICTs) to improve efficiency, mine safety, occupational health, and environmental im-pacts. An integral part of the project is the assessment of these technologies by using key performance indicators (KPIs). The paper will describe some examples of the selected KPIs and the preliminary findings.

Jan 1, 2014

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By J. Uys, P. J. Mokganya, J. Olwagen, R. C. W. Webber-Youngman

This article discusses the critical role of leadership in the technology adoption process within organizations, particularly in industries like mining, where innovation is essential for maintaining competitiveness and operational efficiency. It highlights the limitations of traditional technology adoption models, such as the Technology Acceptance Model (TAM), Diffusion of Innovations (DOI), and Unified Theory of Acceptance and Use of Technology (UTAUT), which focus on individual factors and overlook the strategic and organizational roles of leadership. The study proposes the Ambidextrous Leadership-Technology Adoption (ALTA) model, which integrates leadership styles such as transformational, transactional, adaptive, and ambidextrous leadership into the technology adoption process. The model emphasizes the balance between exploration (fostering innovation) and exploitation (ensuring operational efficiency). The findings suggest that transformational leadership fosters innovation by encouraging risk-taking and creativity, while transactional leadership ensures efficient technology integration. The article also identifies key barriers to technology adoption, such as organizational resistance to change, which can be mitigated through adaptive leadership that addresses employee concerns. The research emphasizes the importance of a supportive organizational culture and cross-functional collaboration, which are essential for successful technology adoption. The study concludes by offering practical recommendations for leaders to foster a culture of innovation, manage resistance, and balance short-term efficiency with long-term technological advancement.

Nov 27, 2024

By P. L. Ngwenyama, W. W. deGraaf

South Africa is one of the leading producers and exporters of coal globally. A significant amount of the country’s production is obtained from previously mined underground bord and pillar workings. This coal is in the form of pillars and remnants on the roof and floor of the old workings. The good quality coal pillars were left behind as primary support during underground bord and pillar mining operations. Due to the depletion of virgin coal reserves, the pillars and remnant coal are now removed using opencast mining rather than underground methods. However, the secondary extraction of pillars and remnant coal from the old workings using opencast methods entails some serious challenges that have a negative impact on the safety and productivity of the operations, affecting both personnel and machinery. If these risk factors and challenges are managed properly, then the opencast mining operations could remove the pillars safely at recoveries competitive with those of virgin coal operations. In this study we review the recurring challenges affecting opencast pillar mining by means of field investigations and consultations with experts at five opencast pillar mining operations, and evaluate the best practices used to combat these challenges. It was found that each mine has its own unique conditions and challenges.

Dec 1, 2021

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003