Search Documents

By J. J. Dekker

Controlling noise has proven difficult in mining, and noise-induced hearing loss (NIHL) remains common. In 2008, a South African Mine Health and Safety Council study focused on small- to medium-sized mines in relation to the milestones set by the industry to prevent NIHL. An evaluation of the compliance of ten diamond, sand, aggregate and Ready mix concrete mines and production sites with standards, legislation and best practice guidelines relating to NIHL prevention was conducted, using a noise compliance audit tool. The findings indicated that all mines surveyed had poor compliance with the international standards, compliance with International Standards Organization standards being the poorest. There was a clear distinction between the small and the medium-sized mines in their compliance with local standards and legislation (ranging from 14 per cent to 66 per cent). The areas of best compliance were audiology and medical examinations. The lower-than-expected compliance was largely attributable to shortcomings in hearing conservation programmes for occupational noise. Initiation of remedial practices in the small- to medium-scale mining sector to facilitate improvements in NIHL prevention and compliance with standards and legislation is recommended. Keywords Hearing conservation, small-to-medium mines.

Jan 1, 2011

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009

By M. Dworzanowski

The beneficiation of fine iron ore will increase in importance in the future because most new iron ore resources will be in the form of lower grade ore deposits that will require liberation of iron ore minerals at finer sizes. Generally this fine iron ore will be beneficiated to produce a pelletizing concentrate with very strict chemical and physical specifications. In addition, because of the increasing demand for iron ore there are now more opportunities to produce by-product iron ore from mining operations producing other commodities. In the past the associated iron ore minerals would report to final tailings but now there is potential value to be realised from by-product revenue. These by-product iron ore opportunities are almost all centred on producing pelletizing concentrate. Currently pelletizing concentrates are produced mainly by various combinations of flotation and magnetic separation. The selection of the beneficiation route will depend on ore mineralogy and considerations around plant capacity and final concentrate quality. The main economic iron minerals are magnetic, haematite being paramagnetic and magnetite being ferromagnetic. This, therefore, means that magnetic separation can be applied, in principle, to all fine iron-ore beneficiation plants. While flotation has a considerable capacity advantage over magnetic separation, the real advantage of magnetic separation over flotation in fine iron-ore beneficiation is that treatment of -10 µm iron ore is possible-in flotation, the feed is deslimed at 10 µm and the -10 µm stream is considered to be final tailings, even though there is often a significant amount of contained iron ore. This paper describes a study around the recovery of fine magnetite in the form of a pelletizing concentrate. The study is based on an evaluation of an iron ore by-product opportunity from an iron oxide copper-gold (IOCG) deposit. Experiments were conducted to quantify the differences in magnetic separation performance with decrease in particle size treated. A mineralogical evaluation of all the test work products was undertaken to facilitate the interpretation of the test work results. These results were then used to propose an economically viable flowsheet for maximizing fine magnetite recovery using magnetic separation.

Jan 1, 2012

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022

By A. K. Raji, M. O. Ojumu

Robotic subsea dredging crawlers are dynamically and remotely controlled vehicles that are used for deep sea mining and recovery operations. These exploration machines are released from a mother ship and move around on the ocean floor using tracks. Current ocean crawlers such as the MK3 ROST are hydraulically powered. In this paper we develop a scaled-down model for simulating and performing static loading analysis of an electrically powered robotic subsea dredging crawler (EPRSDC). The modeling, simulation, and analysis were carried out using modelling software from Solidworks. The structural frame was assembled using the Tetrix max robotics kit. The kit’s structural components were produced from 1050 aircraft-grade aluminum. The results were used in optimizing and for considering other materials, and the to identify specific areas to be reinforced in future crawler designs.

Oct 3, 2023

By J. P. Bergh

The advent of low-quality export coal demand has brought a new range of possibilities to the South African coal industry. Products that traditionally were only of value to the domestic or combustion industry sectors now have the potential to be exported, with only minor amounts of upgrading required through beneficiation. Comparatively high steam-coal export prices can be obtained for lowquality export coal, which enhances the economic feasibility of expanding low-quality thermal coal exports. There are, however, increasing concerns about the feasibility of lower quality thermal coal exports and the broader implications. These concerns relate to the environmental impact of low-quality thermal coal production for export and the inherent threat to the security of domestic thermal coal supply in South Africa. Against this background, this paper serves to explain the extended value chain in the production of export coal. The technical and economic advantages and disadvantages of low-grade exports versus coal production for domestic use are evaluated. The value chain estimation is calculated by the beneficiation modelling and characterization of two coals. Based on the value estimation, the lowgrade export production scenario, and finally the modelling of potential pollutant distribution, are described. Keywords coal beneficiation, techno-economics, thermal coal, dense medium processing, dry processing, fine coal processing, environmental impact.

Nov 1, 2013

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

By A. Tekin

In almost all branches of industry, machinery and equipment in operation cause vibration. Some sources of vibration affect only the operator’s hands, fingers, and arms, while others have adverse effects on the entire -body. Various types and numbers of machines are utilized in the mining sector, and operators with them are exposed to mechanical vibrations caused by the mining machinery they use. A field study was conducted to evaluate the vibration risks to the operators using mining machines in open pit mines. Vibration levels and whole-body vibration (WBV) measurements using various types brands, and models of construction equipment were evaluated in three different mines in the west of Turkey and compared to the the criteria specified in the EU 2002/44/EC directive and ISO 2631-1 (1997) standards. The results showed that operators using mining machinery for 8 hours were exposed to WBV levels below the EU limit (1.15 m/s2), while 44% of these operators were exposed to levels above the EU action limit (0.5 m/s2). Measurement data collected from the working environment and the recommended improvements that need to be made to reduce WBV exposures are presented.

May 2, 2022

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By N. C. Steenkamp

Lightning has been observed in dust clouds following open-pit blasting. It is proposed that the occurrence of this phenomenon is related to the physical composition and characterization of the mineral fines that comprise the bulk of the dust cloud. Silicate minerals, which are susceptible to fine fracturing during blasting, generate the initial charge. This is further enhanced by collisions and friction during the turbulent upcast in the post-blast dust cloud. Varying size fractions result in different rates at which these particles drop out of suspension and create a secondary temperature gradient. This results in the creation of two charged zones and increases the potential of developing a discharge in the form of lightning. The ideal prevailing meteorological conditions need to be windless to minimize the effect of particle dissipation and have sufficient moisture toenhance the potential of generating lightning.

Apr 14, 2024

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By M. Mpofu, B. Maphalala, S. Khan, S. Ngobese, D. Roberts

This paper details an assessment of stemming practices at a South African opencast coal mine and their influence on ground vibration and air blast. Quantitative and qualitative analysis methods were used for the study. The parameters assessed for the quantitative analyses included stemming length, stemming material type, blast-hole depth, burden, and spacing. Pre-blast data from the mine was analysed to determine the deviation between actual and mine design stemming parameters. Mine design stemming length was also compared to the rule-of-thumb stemming lengths. Peak particle velocity (ground vibration) and air blast data from seismograph stations around the mine was analysed to determine the correlation between stemming length and excessive ground vibration and air blast. The qualitative analysis involved observations of blasting procedures at the mine to determine compliance with mine procedures. Some level of non-compliance of actual stemming parameters to design stemming parameters was found, which initially suggested that non-compliance may have contributed to excessive air blast. However, further analysis of the seismograph results indicated no direct correlation between stemming length and excessive air blast and ground vibration. Since stemming parameters are interrelated, it is crucial that all blasting procedures, including stemming, are executed in accordance with best practice, and recorded accurately. There is a need for digital systems for capturing on-bench blasting parameters, as the currently used manual data recording and reporting systems are inefficient and prone to error. Improvements to blast designs are possible through efficient and accurate data recording and reporting systems.

Jan 1, 2021

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

By Z. Zhang

The author recently has reviewed the publications on the slag-related research in China since the Sixth International Conference on Molten Slags, Fluxes and Salts in June, 2000. In fundamental aspects, the physical property predictions and measurements, slag-metal reactions, slag-refractory reactions have received close attention, and are briefly described here in this report. More than half of slag-related publications deal with plant investigations due to the requirement of technological improvements and environmental protection. In the present paper, the research on slags in various treatments related to clean steel production and the utilization of the waste slags is briefly reviewed.

Jan 1, 2004

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By M. Reuter, U. Boin

The target of the current metallurgical industry is to recycle and utilize all their by-products, so as to close the sustainable production loop. Slags are the important wastes and by-products of metallurgical industry, which have been treated, recycled and used worldwide. The present paper summarizes the current status of utilization of the various slags from ferrous and non-ferrous metal production, as well as waste incineration, and recycling of salt fluxes in secondary metal production. In addition, the environmental issues of the metallurgical slags are addressed. The metallurgical oxide slags have stone-like properties and, thus, their major applications are in civil engineering field. The slags should be recycled, modified and processed in a proper way, by taking the environmental impact into consideration. With the treatment of salt slags for melting aluminium scraps, as an example, the recycling and elution properties of the salt slags are discussed. Our research indicates that the viscosity of the salt flux is increased with addition of non-metallic components, that a certain percentage of fines remain in suspension, which determines the viscosity, affecting the settling of heavier materials. High slag viscosity will lead to more fine aluminium metal entrapped in the salt slag (may also be seen as a high temperature slurry), and thus increase the load of salt slag recycling. Keywords: recycling, environment, metallurgy, slags, fluxes, salts.

Jan 1, 2004

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By B. McFadzean, M. Tadie, T. Dzingai, M. Becker

Ores from a single deposit may exhibit extensive variability in their mineralogy and texture. The ability to quantify this variability and link it to mineral processing performance is one of the primary goals of process mineralogy. This study focuses on the effect of alteration in three platinum group element ore samples from the Great Dyke in Zimbabwe – two of which were more pristine compared to the third, which was locally classified as ‘oxidized’ ore. These ores are known to be characterized by varying degrees of alteration, resulting in numerous challenges in flotation and affecting both grade and recovery. Alteration, by near-surface oxidation, of the valuable base metal sulphides and platinum group minerals resulted in lower flotation recoveries of Cu, Ni, Pt, and Pd. Evidence of incipient oxidation was more readily observed in the base metal sulphide assemblage than the platinum group mineral assemblage, even though the loss in recovery (because of oxidation) was most significant for Pd. Alteration through hydration resulted in a significant increase in mass pull and dilution of concentrate grade through the inadvertent recovery of naturally floating gangue comprising composite orthopyroxene and talc particles. In this study, the amount of naturally floating gangue was more strongly correlated with the talc grain size distribution than the grade of talc in the flotation feed. The oxidation and hydration alteration reactions are not necessarily mutually exclusive, although one may be more dominant than the other, giving rise to ore variability.

Sep 1, 2021

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012