Search Documents

By Michael J. Martinson

A powerful methane explosion in the mid-shaft pump station of a main service and ventilation shaft killed several persons on the station; more workers were killed when a mancage travelling down the shaft fell to the shaft bottom under a pile of broken concrete slabs from a brattice wall destroyed by the explosion venting into the shaft and a tangled mass of twisted steelwork from the equipped compartment. The newly-commissioned shaft serves a recent extension of an established mine on the Orange Free State (OFS) goldfield in South Africa. After outlining the circumstances in which the paper was written, and reviewing the nature and extent of the methane hazard in OFS mines, the paper describes the physical layout of the shaft and summarises evidence given by witnesses at the official inquiry concerning events prior to the explosion. No attempt is made to apportion blame for the incident.

Jan 1, 1989

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

Tables

Jan 1, 1973

By Terry S. Maley

With some exceptions, minerals may be acquired on the unappropriated public lands by one of three methods: (1) mining claim location under the General Mining Law of 1872; (2) mineral lease under the Mineral Leasing Act of 1920; and (3) sale contract under the Mineral Materials Act of 1947. Leasable minerals such as oil, gas, coal and phosphate are specifically designated as leasable in the Mineral Leasing Act so the method of acquisition is clear. As a general rule, metallic minerals are acquired by mining claim location. However the nonmetallic minerals, most of which are industrial minerals or gemstones, present a more difficult problem. These minerals are acquired either by mining claim or a sale contract depending on their chemical composition, physical properties and the use to which they are put. The Act of July 23, 1955 (30 U.S.C. 61 1) provided that uncommon varieties of sand, stone, gravel, pumice, pumicite or cinders are locatable; whereas, common varieties of such minerals may only be acquired by a contract of sale. The widespread location of mining claims to appropriate such deposits has caused many land management problems. Federal court and Interior decisions offer the most useful guidelines in determining the most appropriate method of acquisition.

Jan 1, 1991

By Joseph M. Tarantino, Eric F. Perry, Keith B. C. Brady, Michael W. Smith

The Pennsylvania Department of Environmental Protection in 1998 reviewed its permitting process to determine how effective its program has been in preventing pollution and to identify here it could be improved. Of the 1,699 bituminous mine permits issued from 1987 to 1 996, 50 were identified to have current or past postmining discharges with water quality problems. The remaining 1,649 sites had no known current or past postmining discharges problems. The 50 sites were selected for further review. On closer examination, 33 of these permits no longer had water quality problems or the problem had not actually resulted from the permitted mining activity. Only 17 permits, or one percent of the total permits issued, were found to have caused long-term postmining discharges serious enough to require treatment and prevent bond release. Analysis of these 17 sites using current knowledge of mine drainage prediction, revealed that the most common cause of error was inadequate information in the permit application. Errors in interpretation of the application data and in implementing the permit were less common. A very small percentage of all permits issued resulted in postmining discharges for no clearly identifiable reason. Trends over the 10-year study period indicated a decreasing incidence of permits resulting in postmining discharges. Further, with the exception of the first few years of data, most of the postmining discharges were of mildly acidic or alkaline quality and amenable to passive treatment.

Jan 1, 2000

By C. Orf. Chukabarah

Acoustic pollution (noise) is a significant mine environmental system problem. The U.S. Bureau of Mines (USBM), Environmental Protection Agency (EPA), Department of Labor (DOL) and other researchers have all performed contributory research on noise in mining environments. The present study addressed the problem of unavailability of a computerized, practical, routine, user-friendly, and user-editable, prose-styled application program with which one can determine (a) the noise exposure indices among mine workers, (b) mine system noise exposure level on time-weighted average basis, and (c) predictive relationships among mine workers' age, prior exposure to abnormal noise levels, prior auditory pathologies and the risk/degree of mining-induced hearing impairment. Results showed that such a program ("NEIL") is accomplishable. Additional results revealed that most U.S. mines operate within the statutory noise exposure levels. Furthermore, the mine worker's age was statistically confirmed to be the main predictive risk factor for mining-induced occupational hearing impairment.

Jan 1, 1992

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME) Inc., the president of SME formed Working Party No. 79, Ore Reserve Definition. Its mission was to develop guidelines for the public reporting of exploration information, resources and reserves. These guidelines were published in the April 1991 issue of Mining Engineering,(pp. 379-384), and as a document entitled "A Guide for Reporting Exploration Information, continued on an ad-hoc basis until 1996. Working Party No. 79 was then renamed the SME Committee on Re¬sources and Reserves and became a standing committee. Since 1994, the Council of Mining and Metallurgical

Jan 1, 1999

By Osvaldo A. Bascur

The implementation of continuous quality improvement is the confluence of Total Quality Management, People Empowerment, Performance Indicators and Information Engineering. The supporting information technologies allow a mineral processor to narrow the gap between management business objectives and the process control level. One of the most important contributors is the user friendliness and flexibility of the personal computer in a client/server environment. This synergistic combination when used for real time performance monitoring translates into production cost savings, improved communications and enhanced decision support. Other savings come from reduced time to collect data and perform tedious calculations, act quickly with fresh new data, generate and validate data to be used by others. This paper presents an integrated view of plant management. The selection of the proper tools for continuous quality improvement are described. The process of selecting critical performance monitoring indices for improved plant performance are discussed. The importance of a well balanced technological improvement, personnel empowerment, total quality management and organizational assets are stressed.

Jan 1, 1995

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By G. T. Lineberry, B. R. Yama

Artificial intelligence research has produced several tools for commercial application. Some of the techniques that are widely used today include neural networks, fuzzy logic and expert systems. Artificial neural networks (ANNs) are excellent predictive, pattern recognition and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process-control applications. Modeling of spatial data, ore-reserve estimation, tunnel design, long wall-stability prediction and geologic roof classification are additional applications in which neural networks have been applied successfully. In this study, a standard back propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, the performance of the network is measured on an independent validation set. Results indicate a mean error of less than 1 % between the actual and predicted values. A neural network model was developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values for given coordinates. The neural network not only performed satisfactorily, but in some cases performed even better than the kriging model.

Jan 1, 2000

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997

By S. C. Lamey, P. A. Hesbach

This study evaluated the use of regionally produced coal combustion products to neutralize and remove metals from acid mine drainage (AMD). Synthetic AMD mixtures were treated with a number of fly ashes and fluidized bed combustion (FBC) ashes. All of the ashes reduced the volume of the sludge produced and gave a faster settling rate than the sludge produced by treatment with lime. Faster settling allows greater throughput rates. In addition, the FBC ashes, which generally contain alkaline components used for sulfur capture, completely neutralized the acidity and, if desired, raised the pH above 10. The fly ashes, on the other hand, reduced the final volume of sludge but required additional neutralizing agents to attain a pH >5. The pH of the AMD can be taken to above 10 to insure complete removal of manganese, or it can be taken to a more neutral pH of 7 or 8 to allow for the safe introduction of the aqueous phase into ponds or streams. The process combines two industrial waste products to reduce the disposal volume of one of the waste products and to produce an environmentally safe aqueous discharge.

Jan 1, 2002

By Ken J. Fair, Vicken H. Aprahamian, Gus Van Weert

A consortium of Canadian mining companies, engineering firms and the Ontario Government has supported Hydrochem's efforts in the last year to design and cost a 10 tpd NITROX PROCESS® demonstration plant. A 5 kg per hour mini plant was installed at the Hydrochem facilities in Brampton, Ontario. This paper describes design testwork on Dickenson Mines arsenopyrite concentrate and application of the findings to the demonstration plant flowsheet. The control of nitrates in discard solids and stack gases is discussed in detail. Nitric acid oxidation of arsenopyrite results in significant ele- mental sulphur formation, enough for it to be detrimental to sub- sequent cyanidation. Flowsheet variations aimed at dealing with this process characteristic are discussed and testwork results on one option (hot liming) are described.

Jan 1, 1988

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

Bigger is indeed better in today's surface mining operations. That is especially true regarding haul trucks. Building larger, "supersize" trucks, however, means designing more powerful engines and drive systems that are also more efficient and environmentally friendly. And miners are demanding that these trucks have longer service lives with minimum maintenance. So truck makers are teaming with engine manufacturers and mining customers to design these larger trucks that will ultimately lead to reduced mining costs. About 180 of those truck makers, engine designers and miners gathered in Tucson, AZ in September to discuss the state of haul trucks in today's mining environment. Haulage 2000 was sponsored by World Mining Equipment and attracted attendees from around the world. Manufacturers described the latest in haul truck advancements. These included the design of more powerful engines, improvements to mechanical and ac and dc drive systems and suggestions on how to reduce maintenance spending. Technology improvements in tires for larger struck was discussed as was the cost efficiency of new, lighter-weight bed liners. The following is a summary of a handful of the presentations.

Jan 1, 1997

By R. Hiebert, M. Canty, S. Beckman

An innovative biological process is described for the treatment of cyanide-, metals- and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and to immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process-waste stream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), funded by the US Environmental Protection Agency (EPA) and jointly administered by the US De¬partment of Energy's (DOE) Western Environmental Technology Office (WETO) under Interagency Agree¬ment Number DW89938513-01-0. The Superfund Innovative Technology Evaluation (SITE) demonstration program was also involved in the project. MSE Technology Applications Inc. (MSE), Butte, MT, was the contractor responsible for conducting the project, and Pintail Systems Inc., Aurora, CO, was the technology provider. The pilot-scale unit was field-tested at Echo Bay's McCoy/Cove Mine southwest of Battle Mountain, NV. The biotreatment process was considered successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed from the mine process water. From the results of these pilot-scale tests, it was concluded that the biotreatment process potentially of¬fers an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 2000

By Ning Liu, Xuming Wang, Yongqiang Lu, Jan D. Miller

Bench-scale flotation experiments have been conducted to study the effect of nonionic polyethylene oxide (PEO) polymer surfactants on the flotation of Florida phosphate rock. It has been found that PEOs having a molecular weight from 1,200 to 8,000 are effective. Flotation results demonstrate that the addition of nonionic PEO has a favorable effect on phosphate flotation, especially on the flotation of coarse phosphate feed. At about the same collector level, phosphate recovery can be improved by 10-30% with PEO addition. The surface chemistry of phosphate flotation using the fatty acid/fuel oil/PEO system has also been studied to better understand the phenomena involved. The increase in phosphate recovery with PEO addition has been attributed to improved dispersion of fatty acid, which leads to better froth stability and a more hydrophobic surface state.

Jan 1, 1999