Search Documents

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By E.C. Jong

Resumen ¦ Un sistema de comunicaciones “a través del suelo” (TTE) comercial y disponible fue evaluado en una mina de carbón subterránea en la zona Este del Estado de Kentucky. Este estudio de campo fue realizado como parte de una evaluación multisitio mayor de sistemas TTE disponibles. La mina detallada en este estudio se encontraba paralizada al momento de la evaluación, lo que proporcionó la representación más cercana a la realidad del medio ambiente en una mina luego de una operación de cierre. Para este estudio se probaron las comunicaciones superficie a subterráneo y subterráneo a superficie. El despliegue estándar del sistema TTE usando los procedimientos recomendados por el fabricante logró obtener comunicaciones claras y nítidas entre el socavón y la superficie. Otras disposiciones de las unidades arrojaron resultados mixtos. Existen planes para examinar más los fenómenos observados en esta mina.

Apr 1, 2016

By S. E. Phillipson

During the course of evaluations by the Mine Safety and Health Administration’s Roof Control Division, the controls on ground instability were investigated at surface and underground limestone mines throughout the eastern and southern United States. Structural geologic features, including joints and faults, were identified by basic geologic mapping as primary controls on highwall and back instability in surface and underground limestone mines. By comparing the spatial orientation of discontinuities and internal angle of friction with the orientation of highwalls on a stereonet, the potential for sliding, toppling, and raveling failures was evaluated in a semi-quantitative fashion. Structural geologic mapping identified faults and joints, which dismembered the back and were associated with ground instability, in underground mines. This paper documents the importance of recognizing structural geologic controls on ground stability in limestone mines, advocates basic geologic mapping as a critical component of ground control programs at surface and underground limestone mines, and provides examples of simple stability evaluations using the stereonet method.

Jan 1, 2006

By Joseph J. Yancik

An exchange of coal mine specialists was made with the USSR under an "Agreement on Exchanges and Cooperation in Scientific, Technical, Cultural, and other Fields for 1972-73," which was signed by President Nixon and Chairman Breshnev on April 11, 1972.* This exchange, in the field of coal mine safety and scientific research in hazard control technologies, was one of 16 technical exchanges covered under the above agreement. A six-man USA delegation visited the Soviet Union from September 9 to September 21, 1973. The delegation visited four deep mines, three in the Donets Basin and one in the Moscow Basin, a State Safety Research Institute, a Mine Research Station and associated Research and Design Institute, two Research and Design mining equipment institutes, and a Trade Union-sponsored health sanitarium. In Moscow, the delegation received a briefing on the Soviet coal industry from First Deputy Minister Vladimir Fedanov. A similar briefing was given to us on the Donets coal basin by the Deputy Minister S. Saratikyanz of the Ukrainian Coal Ministry. Lengthy technical discussions were held with the mines staff and research personnel at the institutes we visited. In addition, we had detailed discussions with key staff members of two combinats "Donetskugol" and "Tulaugol." In all these meetings, principal topics were matters of safety related to hazards associated with face mechanization, coal transport, methane gas control measures, gas outbursts, coal and rock outbursts, fire fighting add control, explosion suppression and control measures and other related hazard factors. There was also much discussion on miner training, miner's attitudes toward safety and accident prevention practices, and preparation and enforcement of safety rules and regulations. The delegation was very warmly received and constant attention was given to our needs. Our numerous questions were answered with candor although quite often in not as much detail as we would have liked.

Jan 1, 1974

By B. Whisner, A. Smith, J. Carr

"Electromagnetic based proximity detection systems (PDSs) are utilized on mining machinery to protect workers from being pinned or struck. These systems generate magnetic fields covering the space around a machine, and a miner-wearable component (MWC) detects the field. The PDS determines the distance of miners relative to the machine based on the detected magnetic flux density in the magnetic field. This information is used to establish warning and shutdown zones around the machine. Maintaining a stable magnetic field is essential for system accuracy. However, components used to generate magnetic fields can be influenced by temperature changes. Depending on ventilation conditions and seasonal alternation, a PDS can be subject to significant temperature fluctuation. To better understand and quantify this phenomenon, researchers from the National Institute for Occupational Safety and Health (NIOSH) developed an experimental apparatus to study the influence of temperature on magnetic field generator circuits used in PDSs. Results from the study show that the electric current through a generator can be influenced by both ambient and internal temperatures, modifying the magnetic field that is produced. These findings show that temperature can significantly influence the ability of PDSs, used in underground coal mines, to accurately determine a worker’s position in relation to mining machine. INTRODUCTION Electromagnetic based proximity detection systems have been developed to reduce machine-related accidents in underground coal mines. The first proximity detection systems installed in underground coal mines were developed for continuous mining machines (CMMs). There are five of such proximity detection systems that are approved for use in U.S. mines by the Mine Safety and Health Administration (MSHA) (Mine Safety and Health Administration, 2013; Mine Safety and Health Administration, 2015). There are several basic components that interact within an electromagnetic proximity detection system (PDS). A PDS includes two main elements: a set of generators to create magnetic fields around a CMM and a set of magnetic probes to detect the fields. These systems can determine if a miner is located at a safe distance from the machine based on the detected magnetic flux density. Stability of the magnetic fields is essential for system accuracy."

Jan 1, 2018

By Smart Chika Obiora, Anthony Chukwu

Mining and processing of raw materials is one of the earliest activities of man for survival and development. The products are used for making jewelleries, metal tools, and for exchange of goods and services. However, despite the benefits of mine recoveries, it’s negative and long term effects on the environment and lives remain the point of discussion throughout the world. This study summarizes findings of researches in active/abandoned lead–zinc mines in Enyigba and Ishiagu mining districts including social surveys in the localities surrounding the mines in order to ascertain the effects on the inhabitants. Lead–zinc mining in Enyigba and Ishiagu, southeastern Nigeria has lasted for decades and has affected the socio-economic well-being of the host communities. There are evidences of soil, water, and plants contamination by Pb, Zn, Cd, and Mn in these mining communities. The mining activities also affect the overall social development of the host communities. These effects include retardation in educational development, health care provision, unemployment, and access to potable water supply. Others are rise in poverty level, social amenities, sanitary/hygiene level, high cost of living, and fertility rate. Possible mitigation strategies such as to liaising with relevant government agencies in collaboration with mine owner, mine workers, and host communities can ameliorate these negative effects and promote environmental sustainability.

Feb 24, 2023

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017

By S. Amirshenava, S. Nadimi

"Premature and unplanned mine closure can result in significant adverse impacts on the environment and community and need to be managed appropriately. Risk management techniques can reduce the negative impacts and risks of early mine closure. Risk Assessment 3D Model, is an efficient tool to quantify risk. The aim of this paper is to identify the mine closure risks in Choghart iron ore mine, and calculate the overall mine closure risk level. The result shows that 51.4% of assessed risks have low risk level and the overall risk level of early mine closure is low. Keywords: mine closure, risk assessment 3D model, Choghart iron ore mine INTRODUCTION The modern mining life-cycle can be divided into three main stages; exploration, mining (opening and production) and post mining (mine closure, and reclamation). Mine closure is the critical component of the modern mining life-cycle and it refers to the period of time when the operational stage of a mine has permanently ceases (Heikkinen et al, 2008). Planned closure occurs due to the depletion of ore reserves, but sometimes it is premature. Laurance (2006) shows that only 25% of mine closure in the past 30 years was due to resource depletion and in 75% of the cases the mines were closed for the other reasons. Ghanbari et al (2010) demonstrated that 48.6 % of copper mine closure in the past 100 years was due to resource depletion and 51.4 % of copper mines have been closed due to other reasons. The main reasons of premature mine closure are as follow (Laurance, 2006; Ghanbari et al, 2010; Maiti, 2013): • Economic, (low commodity prices or high costs) • Geological, (over-estimation of grade and tonnage) • Geotechnical (adverse geotechnical conditions) • Technical (equipment failure) • Regulatory, due to safety or environmental breaches • Social or community pressures • Closure of downstream industry or markets • Flooding or inrush Minaei Mobtaker and Osanloo (2013) developed a mine closure prediction model based on the data collected from closed iron ore mines in the past 100 years. They showed that economic factors, exhaustion of ore reserve and geological conditions are the main reasons of iron ore mine closure. They treated mine closure as a decision making problem in order to predict the causes of mine closure, including the uncertainties of some mine plan parameter such as iron ore price, production and consumption."

Jan 1, 2016

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By Fabio Mielli

The mining industry is a multifaceted industry with special characteristics that make efficient and intelligent operations uniquely challenging, and subsequently call for distinctive and tailored solutions. Not only does mining call for processes that are complicated and energy intensive, but complex material movements and an intricate logistical chain add to the industry?s obstacles in achieving sustainability and performance. This article explores three major challenges and the resulting issues currently being faced in the industry, as well as potential solutions to these impediments by use of energy management, automation and control strategies.

Jan 1, 2011

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017