Search Documents

By O. Olajide, E. H. Cho

A laboratory study of the jigging process with Pittsburgh seam coal has been conducted. The laboratory-scale Baum jig used in this study was a McNally-Norton LO30X Right Hand Model Baum jig with an effective screen area of 0.186 m2 Feed material was prepared by selecting a size range from 6 mesh to 1.91 cm. Solid feed rates were 27.2 kg/min and 32.7 kg/min. Water flow rates were varied from 37.9 to 94.6 L/min. It has been found that smaller particles give higher values of density of separation and lower efficiency of separation. Increasing water flow rate increases the discharge rate of clean coal at a constant solid feed rate. It appears that the efficiency of separation increases by increasing water flow rate up to a certain value, and then levels off upon increasing the flow rate further.

Jan 1, 1988

By M. G. Ayat

Engineers in the field of coal preparation are continually striving to increase the efficiency of various circuits used in preparation plants. Undoubtedly, one of the important factors concerning the processing efficiency of a coal preparation plant is improved analyses and control of the processing equipment. The necessary link between the performance criteria of a circuit may be provided through on-line determination of various parameters. Currently, there are a certain number of on-line instruments developed for measurement of ash content of coal (Watt and Sowerby, 1983; Kawatra, 1976; Fauth et al., 1984; Lyman and Chester, 1980), moisture content (Hall et al., 1969), and sulfur content (Stewart et al., 1974). In the case of coal separatory units, these parameters are often directly related to the quality of the product. In other words, the extent of misplacement of refuse in the product, or vice versa, would indicate the performance characteristics of any particular coal washing equipment. Partition curves are therefore established to predict the performance of coal cleaning operations. Conventional sampling and testing is currently the major tool with which partition curves are produced and the performance efficiency of the operation is assessed. While conventional analysis techniques are accurate, they are slow and time-consuming.

Jan 1, 1987

By B. K. Mishra, S. P. Mehrotra, Anand Katti

Particle-size monitoring has become routine plant prac¬tice, and on-line measurement techniques have facilitated the proper control and monitoring of particle size. In this paper, the progress on an on-line size measurement technique using a y-ray source is discussed. The tray is emitted from a nucleonic density gauge (NDG) that serves as a slurry den¬sity-measurement device. This unit is calibrated and tested to predict the slurry density. Batch experiments were conducted to study the variation in slurry density of different types of ores, namely, quartz, bauxite and hematite. This data, in turn, is used to predict the size distribution of the solid particulate material making up the slurry. To calculate this size distribu¬tion from the slurry density, the theory of incremental sedi¬mentation is used. Experimental results show that the pre¬dicted size distribution compares well with the actual size distribution, as measured by the Andreasen pipette technique. Finally, a simplified scheme is proposed to monitor on-line size distribution using the nucleonic density gauge

Jan 1, 2000

By H. K. Lin

Cyclic voltammetric and potential step chronoamperometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic peaks and one cathodic peak appear on the voltammogram between -0.50 and 0.80 V vs. SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH and cyanide on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2002

By Derek G. Cieplinski

Regenerative conveyors with complex conveyor profiles place unusually stringent demands on the starting drive control. Depending on the nature of the conveyor loading, the drive must either provide a positive driving force to overcome conveyor friction and gravitational forces if the belt is empty or the inclined sections are loaded, or it must provide a retarding force to resist the gravitational load of decline sections to control the acceleration rate. This paper discusses the requirements of regenerative conveyors, reviews the working principals of fluid couplings, and examines their interaction by means of a case study of a 1700 m long regenerative conveyor utilizing a fluid coupling with a proportional brake control to provide controlled starting and stopping under all load conditions.

Jan 1, 1993

By A. F. Klebanov, K. N. Trubetskoy, M. Yu Khoudine, V. L. Postnikov

The information system of monitoring of mine receive layouts is being created In the "ROSUGOL" Company for the prompt analysis of the state-of-the-art of mining operations at under- ground and open cast mines of the Company, rapid and effective decision-making and elaboration of recommendations on the basic directions of enterprise development. The data bank storing the digital mapping and attributive information describing the actual background of mining operations at the enterprises of the Company is the core of the system. The Oracle database management system and the ARC1 INFO geographic information system have been chosen as basic software packages for the Project realisation. The updating of the information will be performed on a regular basis via the transmission of actual digital data on under- ground and open cast mine layouts In ARCIINFO conversion to the central office of the "ROSUGOL" in Moscow. Centralised storage of digital mapping and attributive data, database administration and navigation is effected with the Oracle software package. Access to the data in the operation mode with an interactive display map will be effected with the use of the local computer net of the "ROSUGOL."

Jan 1, 1996

By Richard D. Doepker, Cathy A. Summers

Part 1: Physical Characteristics The physical and mineralogical characteristics of samples from five sources in the Western United States were determined using size analyses, microscopic studies, and point counts. These results were combined with leachability assays and the chemistry of leachates obtained during slurry tests to predict sample dissolution characteristics during column leaching tests. Part 2: Dissolution Characteristics Two columns of each sample were leached over a period of 3 years with synthetic rain. Residence times were between 2 and 11 weeks. The samples were subjected to daily and seasonal temperature fluctuations and wet-dry and freeze-thaw cycles. During the latter part of this study, a biocide leachant (sodium benzoate) was substituted for synthetic rain to assess the degree of dissolution caused by biological oxidation. It was found that the presence or absence of barite or carbonate minerals can be used to predict the leaching behavior of the column material.

Jan 1, 1995

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By David Sugden

Intense, tropical weathering of Cretaceous-Tertiary sediments has developed similar laterites in distant areas of the Amazon Basin. In two areas, Trombetas and Paragomina s, bauxites of commercial potential arc found. The bauxite comes mostly from the lower horizon of the three component laterite. The laterite is overlain by a clay cover, possibly an integral part of the weathered profile. The laterites are found on almost flat plateaus with individual areas of up to 80km2. There is a close relationship between the morphology and the ldterites. The process of lateritization is allegedly Pliocence but probably continues today.

Jan 1, 1984

By J. L. Fuentes

The so called 'SISCOM' is a General Purpose, microprocessor-based Monitoring and Control System, developed by AITEMIN to meet the requirements of Spanish Mining Industry in - the field of automation and data -transmission. Typical applications -are automatic control of pumps, compressors, fans and conveyors, as well as environmental monitoring and production monitoring. In relation with the last, the - System has been succesfully installed in a full section roadheader and in a mechanised steep coal face. In both cases, the main objective is to get information about running times, down times and causes, -and monitoring of other important parameters such as ventilation, methane content, power consumption..etc. Measurements concerning the face behaviour from a geomechanical point of view are also monitored. These are different pressures and stresses. All data is transmitted to the - surface and on-line analysed by a -desk-top microcomputer. The paper shows the system structure and the requirements that have - been considered on its design. Attention is given to the mechanical data acquisition problem, involving special development of some transducers. The information provided by the surface microcomputer is shown and its utility discussed.

Jan 1, 1986

By Peter J. Suardini

Over the last few years, researcher have been working on improving procedures for fine-coal (minus 150 microns) washability analyses. The effort was stimulated by past difficulties in obtaining accurate and reproducible results from the various commercial laboratories providing fined washability services. This paper contains the results from fine-coal washability testing, performed by Process Technology, Inc. (PTI), as part of a U.S. Department of Energy (DOE)-sponsored project. The testing focused on comparing the performance of a number of media options (i.e., aqueous solutions and organic solvents), as well as evaluating the impact of a number of procedural steps on separation performance. The paper summarizes PTI's recommended washability procedures for various size fractions and ranks of coal, and makes recommendations for future studies of certain phenomenon, such as void penetration and particle density changes, which are not well understood.

Jan 1, 1995

By L. G. Austin, R. C. Klimpel

Batch breakage kinetic tests were performed in a mill of 0.3 m diameter for a range of mill conditions. Accurate simulation required the measurement and use of factors which accelerated the specific rates of breakage of the top sizes as finer material accumulated in the slurry. These factors depended on the size distribution expressed relative to the top size, not the absolute size, suggesting that they are due to a packing effect not a rheological effect. The data simulated correctly a series of steady-state continuous tests in a mill of the same diameter providing values were corrected to the hold-up, ball load, slurry density, and size distribution measured in the continuous mill tests.

Jan 1, 1990

By M. W. Ryan

The US Bureau of Mines investigated cold-cutting alternatives to oxyacetylene torch cutting of metal. The alternatives examined were a pneumatic circular saw with an abrasive cutting wheel, a handheld abrasive water-jet cutting tool, an ultrathermic-cutting system, hydraulic punches and cutters, and a pneumatic reciprocating hacksaw. Sparks generated with the pneumatic circular saw or ultrathermic-cutting system were not completely eliminated with the use of water sprays. The water sprays also reduced the cutting rate of the pneumatic circular saw by 70%. The safety and performance of a handheld abrasive water jet cutting system requires additional research. The hydraulic cutters and punches are readily available and do not introduce any hazards. However, they are not comparable in price to the oxyacetylene gas torch and many different attachments would be needed to replace the torch. The pneumatic reciprocating hacksaw, which did not produce any sparks, is an acceptable alternative in terms of cutting rates. However, the price of the saw and blades is not comparable to that of the oxyacetylene gas torch. The results of this study will further the advancement of safe, efficient alternatives to oxyacetylene gas torches, which will improve miner safety.

Jan 1, 1996

By B. C. Flintoff

In general, process control systems in solid-solid separation have not evolved to the same level as in flotation circuit control. Perhaps one of the more significant contributing factors in this regard is the lack of suitable on-line analytical instrumentation. In spite of the obstacles, some interesting work has been done. This paper presents a review of current industrial control strategies in ore sorting, dense media separation, gravity separation and electrical and magnetic separation.

Jan 1, 1986

By Mark J. Schultz, William J. Francart, Gary J. Wirth

Atmospheric Monitoring Systems (AMS) utilizing carbon monoxide sensors have demonstrated their superiority over thermal type fire sensors for early fire detection in underground coal mines. After proving their capability and dependability throughout the 1980's, systems are now evolving and applying new technologies to enhance their effectiveness and reliability. The use of AMS in coal mines which utilize diesel equipment presents unique obstacles. Exhaust gases from diesel equipment not only raise mine ambient CO readings, but also cause numerous nuisance alarms. Both of these conditions reduce the effectiveness of the AMS. New technologies, such as discriminating devices, smoke detectors, and time delays, as well as administrative controls, have been developed and are being utilized to help reduce nuisance alarms produced by the diesel exhaust. This paper will discuss these technologies and administrative controls which are being utilized in coal mines to enhance the effectiveness of the Atmospheric Monitoring Systems. Reference to specific products does not imply endorsement by the Mine Safety and Health Administration.

Jan 1, 1995

By C. Patrick, D. Puckett

The feasibility of monitoring the locations and vital statistics of equipment and personnel in surface and underground mining operations has increased with advancements in radio frequency identification (RFID) technology. This paper addresses the use of RFID technology, which is relatively new to the mining industry, to track surface equipment in mine pits, loading points and processing facilities. Specific applications are discussed, including both simplified and complex truck tracking systems and an automatic pit ticket system. This paper concludes with a discussion of the future possibilities of using RFID technology in mining, including monitoring heart and respiration rates, body temperatures and exertion levels; monitoring repetitious movements for the study of work habits; and logging air quality via personnel sensors.

Jan 1, 1999

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By B. J. Arnold

A coal's size distribution clay content and moisture content can affect its handling behavior. But the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.'s (formerly EPRI's) Coal Quality Development Center (CQDC) and at Iowa State University (ISU) will answer these questions as part of a four year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of carious coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that while moisture content is the most important variable, the amount of -44 µm (-325 mesh) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1992

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By B. K. Baird, P. C. Satchwell

The application of cutoffs during and after pit optimization is examined for a lower-grade multi-metallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block, incorporating parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which of these parameters have a significant effect on the total contained resource tonnage and total contained non-discounted revenue in the optimized pit. The cumulative effect of changing several of the more significant parameters is investigated. Application of a copper cutoff grade to a block inside the optimized pit could result in the less than optimal extraction of the resource. A block with copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher copper grade block may be sub-economic. The relative merits of applying a copper grade cutoff, “equivalent grade” cutoff and dollar value per ton cutoff to blocks inside the optimum pit are discussed.

Jan 1, 1999