Search Documents

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By Y. FUJII, E. CHANDA, J. KODAMA, D. FUKUDA, M. NISHIHARA, Y. NAKAYAMA, P. SINKALA

This paper describes a creep damage model that was proposed to clarify the rockburst mechanism for the Mufulira underground copper mine in Zambia. Cumulative rock damage was evaluated for the edge elements of each sidewall of the mining drives based on normal stresses by the 3-D displacement discontinuity method (DDM) (Crouch and Fairhurst, 1973). The rockburst occurrences were well hindcasted.

Jan 1, 2023

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By Pawan Bharadwaj, Wim Mulder, Thomas Tscharner, Guy Drijkoningen, Rob Jenneskens

"The Earth’s properties, composition and structure ahead of a tunnel boring machine (TBM) should be mapped for hazard assessment during excavation. We study the use of seismic-exploration techniques for this purpose. We focus on a seismic system for soft soils, where shear waves are better and easier to interpret than compressional waves, as has been shown over the last decade. The system is intended to be deployed on the machine’s cutter head, with a few seismic sources and sufficiently many seismic sensors to tackle spatial variability and noise characteristics. An important property of the newly developed system is its ability to process data with very little human interaction. Images need to be available in near real time, without human interactions slowing down the imaging process. This can be achieved by employing Full Waveform Inversion, which minimizes the difference between modeled and observed data. Because this method may suffer from local minima in the cost function if the data lack low-frequency information, we employ a dedicated seismic source that can generate sufficiently low frequencies for the relevant length scales. With data acquired in a number of field settings that mimic realistic TBM configurations, we show that the designed seismic system can successfully look ahead of the TBM and offers a valuable capability to support decision-making during tunnel excavation. INTRODUCTION While excavating a tunnel with a Tunnel Boring Machine (TBM), the geology and the ground conditions along the planned tunnel trajectory need to be investigated in order to safely and efficiently carry out the underground operations. This entails detecting the occurrence of boulders, foundations, pipes and faults, necessary to prevent hazards and time-consuming delays in the tunnel boring operations. In order to facilitate ground prediction ahead of a TBM, techniques as used in seismic exploration can be deployed. Two components common to seismic-exploration techniques are data acquisition and processing, the latter including inversion. We will discuss each of these for the application to tunnel excavation with TBM, in particular for soft soils."

Jan 1, 2016

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Occasionally, standing supports are used to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for standing supports to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. The Mine Roof Simulator (MRS) was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. Prop models were used to study the effect of a range of roof and floor materials — gray shale, shale and claystone — on the critical buckling loads of the steel props.

Dec 1, 2022

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By C. E. "Sam" Lovewell

In approaching a discussion of production of cement, I hope I won't be like the porter in the bank who was asked if he could give some details on the rediscount rate. He replied, "Boss, when I said hello, I told you all I know." Need for change every so often is illustrated by the story of the little boy four years old who had not spoken a word in those four years. One morning he said, "This damned oat meal is burned'." His Dad was amazed and said, "Son, how come you haven't said a word for four years and now out of a clear, blue sky you say, "The oat meal is burned." Johnny said, "Well, up to now everything has been all right." Not being a mining engineer myself, and my subject not dealing with mining engineering directly, I can only hope that you will agree that the subject has current relevancy by the feet that it can materially improve our environment by putting to good use a potential environmental polluter; namely, fly ash. The profitable utilization of fly ash can reduce cost of use of coal as an energy source. Therefore, it behooves us all to explore to the greatest depth, the pluses and minuses occasioned by its use wherever possible. My particular subject and my particular interest lie in its utilization as a blend in the production of Type IP Portland-Pozzolan Cement meeting requirements of ASTM C-595, Type IP.

Jan 1, 1974

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

By M. M. Veras, C. H. Sampaio, A. S. Young, D. Neto, C. O. Petter

"Due to new technological developments, automatic sensor based sorting has made progress within industrial minerals, precious metals, diamond, and coal mining in recent years (Lessard et. al. 2016). In order to re-introduce the technology to other mining sectors, this research discusses its application to iron, manganese, and zinc ores through test works performed by the authors. These test works were performed using Dual Energy X-ray Transmission (DE-XRT) sensor technology. In each case, pre-concentrations of the ore were created demonstrating the possibility to reduce waste material, energy costs, and water consumption while improving product quality of the ores. INTRODUCTION Sorting of mining ores is as old as mining itself (Salter, 1991). Sensor based sorting applications in coal mining began as early as the late 19th century (Louis 1928). New sensor technologies were developed and implemented sequentially for uranium, nickel, coal, and gold mining (Refining, 1949, Rose et al, 1950, Bloomfield et al, 1966, Clayton et al, 1987, Robben and Mosser, 2014). While these sensor technologies were developed decades ago, computational capacity to keep pace with the vast amount of information required utilizing the sensor technology did not arrive until recently (Lessard et. al., 2016). The sensor based sorting (SBS) process was effectively described by Salter and Wyatt in Minerals Engineering in 1991, and Wotruba and Harbeck in 2010 in the Ullmann’s Encyclopedia of Industrial Chemistry under Sensor Based Sorting. Both descriptions include the following key steps: 1. Presentation of the material or particles. 2. Examination or detection of the material or particles. 3. Processing or analysis of the data generated. 4. Physical separation of the material or particles by external means. Effective presentation of the material or particles is achieved when the sensor is capable of identifying each particle individually. This step requires that each fragment of the material be isolated, and it often involves acceleration of the material fragments by chute or mechanical means, as well as the spreading of particles by vibratory feeders (Salter and Wyatt, 1991, and Wotruba and Harbeck, 2010). The isolated particles typically are conveyed into an area wherein they are subjected to electromagnetic irradiation (except in cases of some radioactive ores), either in the form of x-ray, visible light, infrared, or other energies. A wide range of applications for sensor based sorting exists in the literature. The majority of applications fall into one of two camps, (1) pre-concentration of mineral ores, or (2) characterization of the material during processing (Buxton and Benndorf 2013). While there is much to be gained from in-line material characterization and the resulting control both of quality and processing, this article focuses primarily on the camp of pre-concentration of mineral ores."

Jan 1, 2017

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

Coalbed methane development is an important way to effectively realize a source of clean energy and reduce emissions of carbon dioxide and other gases. However, due to the low permeability of coal seams, the development of coalbed methane in China has encountered substantial barriers. Protective layer mining can efficiently minimize in situ stress and increase coal seam permeability, thus improving gas drainage and avoiding gas disasters. This study analyzed the characteristics of gas migration and the change in permeability during the in situ stress releasing process through experiments and numerical simulation to study the gas drainage effect of a coal mine in an unloaded coal seam under specific geological conditions. First, a stress–strain-seepage coupled test of coal was carried out, and the evolution features of coal permeability during stress loading and unloading processes were investigated. Second, experimental results were used to develop a mathematical model of coal seepage under mining unloading conditions. Finally, a numerical model was developed based on the real geological conditions of the Wulan coal mine to explore the characteristics of in situ stress release and permeability evolution, as well as the gas drainage process in an unloaded coal seam. By combining protective layer mining and gas drainage technology, the risk of gas outburst is significantly reduced.

Oct 1, 2022

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By Jacques Nantel

Mechanization has been at the core of productivity improvements since the industrial revolution. During the past 20 years, mining has derived spectacular progress from mechanization. In the future, however, mechanization alone will not be enough. In the next few decades, automation will bring about new generations of highly productive and safe machines, with low operating costs. Increased use of new and better technology is generally accepted as the prime factor capable of closing the productivity gap. The productivity gap is the difference between inflation and metal prices. The three S-curves in Fig. I represent the evolution of technology in general, and mining in particular. TI represents incremental changes. the dominant sort of technology changes in the mining industry: - Better drills, electric hydraulic drills vs. pneumatic drills, the drilling rate is twice as fast. - Better steel and bits, to accommodate the higher performance drills. - Improved chemical explosives. - Bigger trucks in open pits.

Jan 1, 1993

By J. T. Kline

This paper will present a review of the underground leaching of remnant copper mineralization left as a result of the block cave mining operation at the Lakeshore Mine in Casa Grande, Arizona.

Jan 1, 1985

Never known as a conference to shy away from its share of off-color jokes, the Colorado Mineral Processing Division?s Annual Meeting returned to the Broadmoor Hotel in Colorado Springs, CO April 26-28 for its 62nd edition, this one held under the theme ?Does size matter (is bigger always better).? With the predictable jokes sprinkled in here and there, and a few unpredictable ones as well, the three-day conference featured a healthy mix of talks about some of the latest technical developments in the field of mineral processing, as well as insightful looks at some new operations in the western United States. This year, the Colorado MPD also launched the Wagner Equipment Student Scholarship program.

Jan 1, 2012