Search Documents

By K. Thirumalai

The Bureau of Mines has developed and tested a new concept of combining thermal and hydraulic energy processes for hard rock cutting. The study shows that this novel combination method overcomes the fragmentation limitations of the thermal process in nonspalling rocks and the cuttability limitations of the hydraulic process in high-strength rocks. The method effectively cuts hard rocks at moderate hydraulic pressures (below 30,000 psi). Theoretical predictions of the rock damage process are made and are correlated with experimental results obtained by using both single pulse and continuous water jet hydraulic systems. Traversing point heating and line heating techniques were used for heating rocks preceding the continuous jet impingement. Heating induces structural weakness of the rock material and assists fragmentation by the water jet impingement. The thermohydraulic process is effective if the significant depth of heat penetration induced by the surface heating exceeds the cutting depth produced by the jet impingement. Hydraulic specific fragmentation energy values reduce by about an order of magnitude using the combination technique. The process efficiency and the rate of themohydraulic hard rock cutting increases significantly by increasing the intensity and duration of heating.

Jan 1, 1973

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By D. M. Lane, J. M. Berkoe

Engineers and Owners share a common desire to build reliable, efficient plants on schedule at reasonable costs. This paper describes one tool that Bechtel finds can integrate these objectives by “putting innovation into practice”. Examples of such innovative engineering practice include the use of computational fluid dynamics (CFD) to determine efficient designs. This paper outlines several examples of CFD applications on actual Mining and Metals Projects from around the world. The focus here is to highlight the modeling objectives, analysis strategy, actual benefit obtained from the work, lessons learned to improve future efforts and the common mistakes that can obscure the correct or best results, despite impressive graphics. The tools are powerful, and the results are more powerful when applied with skilled and well-directed human effort and ingenuity.

Jan 1, 2000

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By Paul L. Russell

Introduction As the US and world population increases, so does the problem of supplying expanding energy needs. Early requirements worldwide were mostly met by abundant forest vegetation. Man's large scale use of minerals-energy resources is a fairly recent development. It occurred only during the past 200 years. Coal was the first mineral fuel to be used extensively. It was not a large factor in US energy production until the beginning of the 19th century. Petroleum and natural gas use is about 125-years-old. Electricity generation by falling water is about a century old. Atomic energy is only about 30-years-old. Extensive use of it is still in the future. Solar energy is in its infancy. Other energy sources such as wind, peat, and geothermal energy are minor and primarily of local importance. There were three main features of the fuel supply picture during the past 125 years. By 1900 coal replaced wood as the principal energy source. Since 1900, oil and gas have captured many coal markets. And after the mid-1970s, there was a resurgence of coal usage. (Figs. 1 and 2). Wood Until the advent of mineral fuels for energy, the major global energy source was wood. But populations increased and became centered in towns and cities. The problem of a sufficient energy supply first developed as nearby, easily obtained wood was exhausted. This problem became more acute as industries such as shipbuilding, smelting, and pottery making, became more widespread. Results of wood use as an energy source and building material are starkly evident in areas of the world where civilization is oldest. Entire forests were consumed and have never been replaced. In the US, wood supplied 90% of all fuel requirements until about 1850; and more than 50% until after 1880. By 1900, wood still supplied 20% of all energy uses. In the mid-1970s, energy costs increased, due largely to the oil embargo. This increase resulted in an increased wood demand for domestic heating. While large quantities of wood were being used, its share of the total energy market was still less than 3%. By 1983, wood was becoming increasingly scarce and more costly near most large US cities. Wind Wind powered ocean vessels for many centuries. Sailing ships were still common in 1900. Windmills provided an early, cheap energy source and continue to be used today on farms. Design and development of windmills for electricity generation is being conducted. Interest in wind power is growing worldwide where availability of wind currents warrants the investment. Also, US regulation requires power companies to "buy back" electricity generated by windpower in excess of that used by the windmill owner. Coal By the 1600s, England was producing, 900 kt/a (1 million stpy) of coal for heating and other uses. The first coal-fired blast furnace for iron smelting was developed in 1621. Coke-making was developed in 1755, and Watt invented the steam engine in 1769. Illuminating gas made from coal was introduced in London in 1800. During this same 200-year period, France and Germany developed coal production, but on a smaller scale than England. US, bituminous coal was mined near Richmond, VA, as early as 1748. Major bituminous coal-producing states in the early period were Pennsylvania, Virginia, Ohio, Kentucky, Illinois, and Maryland. West Virginia replaced Virginia as a major producer, when that state was formed in 1863. As the US expanded west, new coal deposits were found and exploited. Indiana, Alabama, Tennessee, Iowa, Kansas, Missouri, Washington, Colorado, Wyoming, Arkansas, Oklahoma (Indian Territory), Montana, New Mexico, and Texas had significant coal mining operations by 1900. Today the eight major coal producing states are Kentucky, West Virginia, Pennsylvania, Illinois, Ohio, Virginia, Wyoming, and Montana. These states accounted for about 80% of all coal (lignite, bituminous, and anthracite) produced in the US during the past several years.

Jan 8, 1984

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By Rick Bearce, Minsu Cha, Mike Mooney, Yuanli Wu, Lisa Mori

"Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. Chamber pressures can reach 3-5 bar yet the vast majority of testing is performed under atmospheric conditions. This paper illustrates how pressure influences foam stability and conditioned soil behavior, and how atmospheric test results must be viewed in the context of expected chamber pressures. Torsional shear strength, compressibility and abrasivity of foam conditioned sand were found to be ideal when the void ratio was above the ASTM-determined maximum void ratio, achieved by sufficiently expanding the soil grain structure with foam, herein when the foam injection ratio at pressure exceeded 45%. Otherwise, the engineering properties of foam conditioned sand were not ideal, i.e., appreciable torque and abrasivity, low compressibility. INTRODUCTION Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. The formation soil at the cutterhead must be transformed into a highly compressible, low shear strength and low permeability medium within the excavation chamber to allow effective EPB performance. This behavior must be maintained for a certain residency time while the soil is in the chamber and screw conveyor. The vast majority of published studies on conditioned soil behavior have been performed under atmospheric conditions (Quebaud et al., 1998; Bezuijen et al., 1999; Psomas and Houlsby, 2002; Vinai et al. 2008; Thewes et al., 2012; Peila, 2014); however, the desired soil behavior must occur under chamber pressures that can reach 5-7 bar. The influence of pressure on conditioned soil is significant and is dramatically different than behavior under atmospheric pressure (Williamson et al., 1999; Mori et al., 2015). This paper illustrates how pressure influences conditioned soil behavior and how atmospheric test results must be viewed in the context of expected chamber pressures. The influence of pressure on foam bubble size (including with time) is shown through digital image analysis. The influence of pressure on foam half-life is also investigated. The compressibility, shear strength, and abrasivity of conditioned soil under pressure is presented and explained in terms of density, soil and air compressibility and porosity."

Jan 1, 2016

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By E. J. Owen, A. Appah, I. C. Sanchez, K. T. Stafford, N. Hurtig, R. Otoo, N. A. Iverson, S. A. Moses, V. T. McLemore

New Mexico lies at the eastern edge of one of the world’s great metal-bearing provinces hosting numerous Laramide and Paleogene mineral deposits. Southwestern New Mexico contains Laramide porphyry Cu (±Mo, Au) and Paleogene Mo-W deposits. Porphyry deposits are generally large, low-grade deposits containing Cu, Fe, Mo, Au sulfides (and other metal sulfides) associated with porphyritic intrusions and exhibit characteristic alteration styles. Porphyry deposits can also be spatially and temporally associated with skarn deposits and polymetallic veins. All of these deposits have the potential to host various critical minerals, including Cu, Zn, Bi, Co, Ni, rare earth elements (REE), Te, and W. Critical minerals may be found as substitutions within ore minerals or as separate mineral phases. These deposits are constrained using 40Ar/39Ar dating into three ore-producing magmatic pulses: 1) ~78–71 Ma Laramide pulse, 2) ~59–50 Ma, Laramide pulse, and 3) ~40–30 Ma Paleogene pulse. New and historic whole-rock geochemical data have highlighted areas with critical minerals potential that require further study.

Feb 1, 2025

By Kendrick C. Hardcastle

Although the basic techniques employed in hydraulic pumping in open pit mining have been practiced throughout the better part of this century, only relatively recently have studies of' sufficient depth and scope been conducted to improve these techniques. This paper will point out the basic techniques involved and some of the more recently discovered data concerning hydraulic pumping, Inherent in all hydraulic transportation systems apart from the consideration of transportation cast, is the outstanding advantage of slurrying the matrix at the mining pit so as to provide a lengthy and thorough soaking and washing of the material while in the pipe line and thereby reduce the necessity for washing, scrubbing and other treatment in the beneficiation plant. This is quite important in view of the constant increase in demand for a cleaner product.

Jan 1, 1964

Introduction Surface mining is a business, and the objective of most businesses is to make as much money as possible within certain responsible constraints. Businesses normally measure their potential to make money by estimating the discounted cash flow rate of return on new projects or the net present value for ongoing projects. These estimators of profitability are calculated using the following well-known equation: [ ] where i is the year, n is the total number of years, A, is the after tax net cash generation in year I, r is the discount rate and NPV is the net present value. In its simplest form, when the value of r makes the NPV equal to zero, the discounted cash flow-rate of return (DCF-ROR) is defined. The maximum economically recoverable reserve is identified at the point where the NPV or DCF-ROR is at a maximum. Depending on the measure used (DCF-ROR or discount rate) for calculating the NPV, the definition of recoverable reserve will be different for exactly the same deposit. Maximization of the measure of profitability and the economically recoverable reserves should not be separated from the mining method and sequence of exploiting the reserve. The surface mining methods may involve multiple-pass development of the resource, mining to the ultimate limit in one pass or a combination of the two methods with backfill. Multiple-pass development When planning a multiple-pass mining operation, it is important to determine the width of pit expansions that are appropriate for a specific situation. Production personnel typically want wide, open work areas where operations can be set up to run at peak efficiency. While this is understandable, the trade-off between highly efficient production operations and an overinvestment in stripping should be carefully weighed. As long as safety is not compromised, a few cents per bank cubic yard increase in operating cost due to lower productivity by working in more confined spaces may well be offset by a decrease in the overall short-term stripping requirements. A mini study on productivity and cost should help quantify this cost before deciding on minimum phasing requirements. The bigger challenge associated with establishing smaller work areas is securing operations and management buy-in to marginally lower productivity when reporting results. When cost reduction is the important management goal and everyone is focusing on unit costs, one sometimes loses sight of the goal of total cost management and, even more importantly, maximum profitability. The first pit should be defined by the first grouping of recoverable mineral that has the highest after-tax unit value and forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. 1 is constructed for a rate of production, R, and a quality management strategy, Q, by calculating the NPV for a series of sequences, with each sequence assuming that the operations are terminated on successively lower profit pits. These values are plotted to form the curve in Fig. 1. If the operation ceases on a pit that has too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have made more money invested at the discount rate than by mining the next pit expansion. Therefore, the maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV. There may be an opportunity to refine the definition of the "ultimate pit" around the maximum-value point. The precise definition of the ultimate pit early in the mine life may or may not be important today, depending on how far off in the future these limits will be reached. By the time an operation must decide on its last increment of economically recoverable reserve. much of the

Jan 1, 2000

By A. B. Cecala

Enclosed cabs have been used on surface mining equipment for many years to protect equipment operators from health and safety hazards. The surface mining and quarrying process is a highly mechanized process that generates large quantities of respirable dust. Due to economic factors, more older mining equipment is being used today than in years past. With this older equipment, it is common to observe deterioration of many components on the enclosed cabs which greatly reduce their protection effectiveness. NIOSH has performed a number of different field studies, as well as a comprehensive laboratory study evaluating various factors and parameters regarding enclosed cabs. NIOSH has recently completed a cooperative research effort with Sy-Klone International and Vulcan Materials Company to evaluate the effectiveness of a newly designed uni-directional filtration and pressurization system that brings all the clean filtered air in at the roof of the cab and extracts all recirculated air near the floor. This design provides the highest air quality to the equipment operator. Testing on this new system showed an almost 10-fold reduction in respirable dust inside the enclosed cab. The uni-directional design is easy to incorporate and should be considered for all new and retrofit systems in surface mining equipment.

Jan 1, 2009

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By Douglas N. Kendall

There are three definite steps in the making of a mining industry in any country. These are as follows: Step A - Geological Mapping This step covers the basic geological mapping of the country at scales of 1/250, 000 up to l/50, 000. This step eliminates territory and directs the exploration teams to the areas of potential interest. Step B Prospecting This step includes all phases from detailed geology through geophysics and drilling up to the point of proving that an economic ore body exists. Step C - Mine Development This is the expensive step, involving the creation of the mine, including shaft-sinking, ore treatment plant, etc.

Jan 1, 1963

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By H. Wesley Peirce

Arizona embraces portions of two major western-U.S. physiographic-geologic provinces and a smaller, local one. These exert fundamental control over the geologic framework and associated earth-material resources and potential. The Mogollon Rim diagonally crosses the State and separates the Colorado Plateau Province to the northeast from the Transition Zone and Basin and Range Province to the southwest. More than 90 percent of the population, production of nonfuel minerals, agricultural land, and water resources are in the Basin and Range part of the State. In 1981 Arizona was ranked number one in the Nation with respect to the value ($2.56 billion) of nonfuel-mineral production. About 8.2 percent of this amount ($212.9 million) can be attributed to nonmetallic (industrial) materials. Although a diversity of nonmetallic substances is produced and some are exported, the bulk is utilized within the State and is directly related to market growth. Since 1950 there has been a fourfold increase in Arizona's population, a concomitant twelvefold jump in sand-gravel production (tons), and a twentyfold increase in "stone" production. New industries developed during this time include cement, salt (and storage of liquid petroleum gas products in solution cavities in salt), zeolite, hydrofrac sand, vitrified clay pipe, crushed marble products (teed additive, pool sand, roofing granules, etc.), and "rock" wool. Most of these newer industries serve out-of-State as well as in-State markets. In 1981 at least 225 industrial mineral or rock deposits were being worked to produce about 10 tons of material per Arizona resident per year. In 1980 the relative values of basic industrial minerals produced in the State, by major group, were cement and lime (51.6 percent); gravel (26.5 percent); sand (11.8 percent); stone (4.6 percent); and others (5.5 percent). Detailed knowledge of the nonmetallic rock-and-mineral content of most Arizona ranges and basins is lacking. Exploration opportunities in this sun-belt growth region appear encouraging.

Jan 1, 1987