Search Documents

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation's work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991

Shallow ore deposits are mined by surface methods but a depth is reached in the case of most deposits after which underground methods are applied for the extraction of the remaining ore. The determination of this depth and its analysis is the subject of this paper. In order to determine transition depth from open-pit to underground mining on the basis of the allowable and economically feasible overall stripping ratios, an economic-mathematical equation is first introduced. Using the achieved equation and an analytical procedure on a particular two-dimensional hypothetical tabulate deposit, an effective formula is then established. The formula introduced here, together with the procedure adopted, could be used in all similar mining situations by the mining design engineer.

Jan 1, 2010

By P. R. Taylor

Three refractory gold concentrates have been tested to evaluate the effect of roasting with hydrated lime followed by cyanidation. The results indicate that it may be possible to roast in such a manner as to contain nearly all of the sulfur, arsenic and antimony in the roaster calcine. Cyanidation results indicate that the gold recoveries are greater than 80% for all three concentrates.

Jan 1, 1993

By K. J. Ma, L. Ma, J. Stankus

The paper’s intent is to evaluate pumpable foamed cementitious mine seal material by determining the shear strength of a generic foamed cement in the laboratory. The tests were conducted on three scales: small-size specimens, consisting of cylinders 4 in. in diameter or 3-in. prisms; double shear medium- size specimens, measuring 13 in. by 10 in.; and large-size specimens, measuring 6 ft by 4 ft by 4 ft. The small-specimen shear tests resulted in average peak and residual shear strengths of 128 psi and 56 psi, respectively. These values are fairly consistent with published shear strengths of foamed cementitious material. However, the other two types of shear tests did not achieve the shear strength of a typical pumpable foamed cementitous mine seal material. Based on the test results, the paper concluded that the structural analysis of cement foam seals should be based on their residual shear strengths, approximately 20 psi, determined from small laboratory-scale tests of the cement foam/concrete or rock interface, and not be based on their peak strengths.

Jan 1, 2015

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By R. F. Merwin

Advancement in automation intensifies the need to remove tramp iron from bulk materials being processed and carried on belt conveyors. Although magnets have long been employed for this purpose, it becomes increasingly necessary that magnetic equipment of appropriate types and sizes be selected and advantageously installed -- if maximum benefits are to be derived Tramp iron present in bulk materials consists of ferrous trash, such as wire, bolts, nails, equipment parts, tools, and machine cuttings. The results, if the iron is not removed, are damaging to equipment having close clearances, explosions, or fire, En the case of flammable materials, production downtime losses, and contaminated products.

Jan 1, 1966

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By Darrell E. Young

This presentation will define what talc is, how it is mined and processed, and how talc is used in the paper industry. It will also give you some idea about who Luzenac America is and from where it came. Luzenac America was formed in July, 1992 as a result of the acquisition of the talc assets of Cyprus Minerals by RTZ of the United Kingdom. Cyprus Industrial Minerals was then merged with the other RTZ talc interests under the Luzenac name. Luzenac is a town in the Pyrenees of Southern France -and the home of Talc de Luzenac, RTZ's first talc acquisition. The Luzenac Group is the largest talc producer in the world.

Jan 1, 1993

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By R. Fernando

"The National Institute for Occupational Safety and Health (NIOSH) National Personal Protective Technology Laboratory (NPPTL) is leading an effort to develop the next generation of self-escape breathing apparatus for egress from confined spaces in emergency scenarios. A backpack style closed-circuit mine escape respirator design was one configuration explored as part of the research imperative directed by the 2006 MINER Act. Stakeholder feedback from MSHA and at the NIOSH Breathing Air Supply Partnership Meeting indicated a smaller belt worn unit that does not sacrifice performance is desirable. This paper outlines some further technology advancements that may be investigated toward developing such a small-sized respirator. Technologies being considered are novel chemicals for improved carbon dioxide (CO2) absorption and oxygen (O2) production, eliminating a dedicated CO2 scrubber by incorporating its function in the spaces of the respirator’s breathing loop and storing O2 in a liquid form with long standby capabilities. When these technologies are applied to a future design, there is the possibility of having an escape respirator that can be belt worn and capable of being certified to 42 Code of Federal Regulations (CFR) Part 84 standards, including sub-part O for escape purposes including mine escape. BACKGROUND NIOSH NPPTL has a Research and Development effort to provide mine workers with state-of-the-art breathing air technologies to comprehensively support initial and continued self-escape, refuge alternatives, and rescue needs, resulting from mine emergencies. As part of this R&D effort, NIOSH invested in the development of a next-generation closed-circuit mine escape respirator (CCMER) which would be compliant with NIOSH’s respirator standard requirements, 42 Code of Federal Regulations Part 84, including sub-part O. The design features of the CCMER also address the MINER Act’s requirements for transitioning between devices without the need for doffing the initially donned device. It would also allow for improved protection when using voice communications with a donned device ."

Jan 1, 2018

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Irvine G. Reilly

Results of a preliminary study of the ammoniacal leaching of covellite (CuS) in an aqueous oxidizing system in the presence of a non-miscible organic sulfur solvent are described. Up to 60% of the sulfur can be recovered from the solvent as elemental sulfur 1 while achieving high degrees of solubilization of the mineral. The effects of temperature, particle size, oxygen pressure, ammonia concentration and ammonium ion concentration on the degree of sulfur recovery were investigated. Maximum recoveries were achieved at moderate temperatures and in well-buffered systems, with a large excess ammonia concentration. Oxygen pressure and particle size were found to have little effect on fractional recovery of sulfur. A simple empirical model based on electrochemical theory correlating the effects of some of the parameters cont-rolling the degree of sulfur recovery is presented. The results of this work also confirm that in any proposed reaction mechanism for the oxidative ammoniacal leaching of copper sulfides, the primary oxidation product of the sulfide ion in elemental sulfur.

Jan 1, 1978

By Fred C. Wrobbel

Two counties in Illinois, Ope and Hardin, and three counties in Kentucky, Crittenden, Livingston and Caldwell comprise the entire Kentucky-Illinois fluorspar district. The output from these five counties, however, makes up over 60 percent of our domestic fluorspar production, amounting to some 175,000 tons of finished product in 1956, The area is rough and hilly. It is bisected by the Ohio River, and has numerous smaller rivers and creeks. Add to this a generous average annual rainfall, in excess of forty inches, and it is understandable that the-area-can boast of an ample water supply. An abundance of water, however, is unfortunately not always conducive to ideal mining conditions. The faulted structure of the area and the soluble Mississippian limestones make the subsurface sediments' willing hosts to the surface water. Limestone cavers and sinkhole topography also compound the occurrence of underground water. It is little wonder, then, that water frequently presents an economic problem in the area, particularly in vein-type mining.

Jan 1, 1958