Search Documents

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By C. I. Basilio

The adsorption of dialkyl di-and mono-thio-phosphinates on gold, silver and gold-silver alloys has been studied in the present work. These reagents, which are selective collectors for sulfide flotation, have been found to improve precious metals recovery from ores. Voltammetric studies have indicated that dithiophosphinate adsorbs on gold at much higher potentials than on silver, while monothiophosphinate adsorbs only on silver. However, both adsorb on gold-silver alloys with the adsorption potential decreasing with increasing silver content. Using FTIR spectroscopic measurements, the surface species formed during the interactions of these collectors have been identified. The results of the electrochemical and spectroscopic measurements have been compared with the contact angle data obtained at controlled potential conditions.

Jan 1, 1992

By E. H. Cho

A current environmental concern is the cleanup and restoration of soil contaminated with low-level radionuclides at DOE sites including the Nevada Test Site. At the present, there is no applicable process to economically and effectively deal with the remediation of contaminated soils. This situation requires development of a selective flotation process to separate the radionuclides from contaminated soil efficiently and economically. In this study, a minus 200 mesh size fraction of pure cerium dioxide was used as a surrogate for plutonium oxide which is the major contaminant at the Nevada Test Site. A Hallimond flotation cell was utilized to examine the flotation behavior of cerium dioxide with oleic acid under various conditions of pH and collector concentration Mechanical cell tests were conducted to float the surrogate from a mixture with uncontaminated Nevada Test Site soil in the absence and presence of calcium carbonate as a carrier. Two different sizes of the carrier (minus 150 mesh and 65-150 mesh) were tested. It was found through the Hallimond cell flotation tests that the cerium dioxide could be floated well at pH&apos;s 4 and 9 with 10-3 molar oleic acid. It was also found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34 % to 65 % by adding only 0.5 % calcium carbonate (minus 150 mesh) in the feed and also increased to 95 % by adding 10 % of this carrier to the feed. The finer size fraction of calcium carbonate (minus 150 mesh) was more effective in recovering cerium dioxide than the coarser size fraction (65-150 mesh) The flotation method utilizing a carrier of calcium carbonate seems to provide a high potential to be used for the remediation of soil contaminated with radionuclides at various Department of Energy&apos;s nuclear weapon sites.

Jan 1, 1996

By J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The Sao Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in 1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000 ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE&apos;s) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years, Many sophistications of the method have been developed during this time. However, the ability to simulate mathematically still hinges on the ability to ignore unimportant details which would complicate the mathematics and make simulation impractical, Thus, with this attitude in mind, it becomes very easy to design a pseudo- simulator which will predict average conditions very well, but can not truly allow a detailed study of the system being simulated. Most simulations fall into this category, along with the case mentioned here. This paper is not intended to be a critical treatise of the simulator used to study a particular mining system. Instead, it will be used to illustrate the aspects of simulator development. The steps in the development of any simulator are described, along with same detail of the phosphate mine simulator itself.

Jan 1, 1966

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines has developed a PC based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1994

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By P. Munjal

"Usage of Supercritical CO2 in place of high pressure freshwater has proven to be a potential breakthrough in the technique of fracturing. Tapping of carbon footprints from feasible sources like industries can be used to manufacture Supercritical CO2 required for fracking. Supercritical CO2, being less viscous than water, creates complex and coherent micro-fractures which can connect many more natural fractures greatly, increasing maximally the fractures’ conductivity leading to an increment in production. The better clean-up property of Supercritical CO2 provides auxiliary benefits of immediate evaluation of fracture zones, usage of an optimized quantity of mesh proppant and elimination of the need of swabbing. Also, Coal has a stronger affinity for CO2 than for CH4. When CO2 is present, CH4 on coal is replaced by CO2. This also ensures rigorous recovery of gas from the coal beds. Use of Supercritical CO2 will obliterate many problems as the CO2 used for fracturing is either sequestered beneath the crust or is recovered at the surface and reused. Therefore, injecting CO2 into coalbeds achieves not only enhanced CBM recovery, but also greenhouse sequestration underground. INTRODUCTION Coalbed Methane At various times in the geologic past, earth had dense forests in low-lying wetland areas. Due to natural processes such as flooding, these forests were buried underneath the soil. As more and more soil deposited over them, these dead plant remains were compressed. As the process continued the plant matter was protected from biodegradation and oxidation, usually by mud or acidic water. Under high pressure and high temperature, dead vegetation was slowly converted to coal. The omnibus process of formation of coal, thus, comprises of conversion of dead plant matter into peat, followed by its conversion to lignite, then sub-bituminous coal, after that bituminous coal, and lastly anthracite. This process of enrichment of coal as it is progressively forced deeper into an ambience with higher temperature and pressure involves biological and geological processes that take place over a long period and is called coalification. During coalification, large amounts of methane-rich gas are generated and stored within the coal on internal surfaces; hence comes coalbed methane. Coalbed methane (CBM), a gas formed as part of the geological processes that are responsible for the generation of coal, is adsorbed into the solid matrix of the coal during its formation process. Coalbed methane is distinct from a typical sandstone or other conventional gas reservoirs, as the methane is adsorbed and not absorbed. The methane is in a near-liquid state, lining the inside of pores within the coal. The open fractures in the coal that result from the liberation of volatile materials (and subsequent contraction due to the liberation) from the coal due to the high temperature and pressure conditions encountered, called cleats, may also contain free gas or can be saturated with water."

Jan 1, 2015

By L. Adler

To properly analyze and apply mining equipment, a systematic, current, inclusive, and simple classification scheme is required. This paper provides such a classification for Roadheaders. This Roadheader classification is based on factors, such as the rock cutterhead, the boom type, and the chassis configuration. It first assigns Roadheaders as an equipment type within the larger group of Integrated Excavators. The Roadheader type is then delineated into the following subtypes: the standard, the extended boom, the tunnelers, and the miscellaneous. Next, these subtypes are devolved into kinds, and finally variants and attachments are considered. To resolve inconsistencies in characterizing the Roadheader, cross-referencing is employed within the classification scheme.

Jan 1, 1996

By M. Misra

The dielectric properties and flotability of different ranks of Argonne Premium Coal samples are presented. The flotability of different ranks of coal are correlated with the dielectric properties and intrinsic moisture (or bound water) content. Measured dielectric properties of as-received coals and other constituents are incorporated into a mixture equation to calculate the dielectric properties of bound water present in the different ranks of coal. The nature of bound water present in low-rank hydrophilic coals is significantly different from that present in high-rank hydrophobic coals. The water molecules present in low-rank lignite have an oriented dipole-dipole interaction and are tightly bound to the surface. For high-rank coals, the water molecules are not bound to the surface and have a randomly distributed clathrate ice-like structure. Controlled thermal treatment can modify the structural nature of bound water present in low-rank hydrophilic coals and increase their flotability.

Jan 1, 1990

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994