Search Documents

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By K. V. Raj, A. T. Weakley, A. L. Miller, D. A. Parks

Diesel particulate matter (DPM) is a common and well-known health hazard in the mining environment. The current approved method for monitoring both the organic and elemental carbon (OC, EC) portions of DPM is a laboratory method with a turnaround time of approximately one week. In order to evaluate exposure levels and take corrective action before overexposures occur, a portable real-time device capable of quantifying both OC and EC is needed. To that end, researchers from the National Institute for Occupational Safety and Health (NIOSH) designed and tested a device based on narrow bandpass optical filters that is capable of targeting infrared absorbance bands associated with DPM. Five optical bandpass filters were chosen based on previous work quantifying DPM using Fourier-transform infrared (FT-IR) spectrometry. The resulting device, referred to as a filtometer, is optimized to exclusively determine DPM and could serve as a cost-effective, field-portable alternative to laboratory-grade FT-IR analysis and instrumentation. The performance of the filtometer was investigated by calibrating FT-IR data from DPM (dependent variable) to the filtometer spectra (predictor variables) using a partial leastsquares (PLS) and ordinary least squares (OLS) approach. The square of the correlation coefficient and root-mean-square error of cross validation m

Mar 2, 2022

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By M. J. Beus

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By R. Jedrzejczak

Endako Mine is an open pit molybdenum mine located in the north central region of British Columbia, Canada, approximately 160 km. west of Prince George. Production for the latter part of 1992 is expected to average at 63,500 tonnes per day of which 27,000 tpd constitute the mill feed. This production is achieved with five 15 to 19 cu. yd. electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 121;.1 inch electric rotary drills. There are three ore zones delineated into pit areas called the Endako, Denak East and Denak West. Present mill feed source is the South East stage of the Endako Pit while the stripping is carried out in the South Wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM/BM/flotation circuits. The majority of the Molybdenum Sulphide (MoS2) is roasted on site to produce technical grade Molybdenum Oxide (MoO3) while a portion is further refined and treated to yield a 99.9% pure Molybdenum Sulphide (MoS2) "Ultrapure" product.

Jan 1, 1993

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests.

Jan 1, 2009

By F. E. Senftle

Preliminary geophysical surveys for nickel deposits are usually carried out by airborne magnetometer and surface electrical methods. Once an anomaly is discovered by these techniques, one must resort to chemistry to identify nickel and determine its concentration. Consequently, a method to determine nickel quickly and quantitatively at the exploration site could help guide detailed sampling and provide analytical data that might otherwise be delayed at distant laboratories. In addition, borehole probes capable of indicating nickel in the rock adjacent to the hole, should prove attractive to the exploration geologist. With these needs in mind, preliminary investigations have been made to demonstrate an in situ analytical technique which appears feasible for nickel exploration. The method depends on the very high energy gamma rays emitted when nickel absorbs a thermal or low energy neutron. These neutron capture gamma rays should be distinguished from the lower energy gamma rays emitted during decay of radioactive nuclides as in conventional activation analysis.

Jan 1, 1971

By C. W. Overton

The operations of Bethlehem Copper are situated in the south-central interior of British Colombia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Colombia. The minerals are chiefly chalcopyrite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies sane pyrite is present. Average grade of mill feed is 0.55% copper.

Jan 1, 1973

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By D. Diekman

Perlite is not a trade name but a generic term for naturally occurring siliceous volcanic rock. A distinguishing feature which sets perlite apart from other volcanic glasses is that when heated to a suitable point in its softening range, it expands 5 to 20 times its original volume. This expansion is due to the presence of 2% to 6% combined water in the crude perlite rock. When quickly heated above 1600°F (871°C) crude perlite pops in a manner similar to popcorn. The combined water vaporizes and creates countless tiny bubbles in the heat softened glassy particles. It is these tiny glass sealed bubbles which account for the amazing lightweight and other exceptional physical properties of expanded perlite. The bulk densities of the expanded perlite generally range from 3 pounds per cubic foot (48 Kg M3) to 10 pounds per cubic foot (160 Kg H3).

Jan 1, 1985

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By L. B. Phelps

The nation is confronted with thousands of acres of abandoned coal lands. In Pennsylvania alone, these lands have been estimated to cost $15 billion to reclaim (Pennsylvania Bulletin, 1985). One way to deal with this problem is to provide a mechanism by which the active mining industry can undertake to remine certain of these abandoned mine areas. Remining is classified as reaffecting previously mined areas in order td extract the remaining coal reserves while improving the environmental quality of these lands through land restogation and abatement of pollutional discharges. However, there currently is a disincentive for operators to plan to extract reserves on these abandoned mine lands which have preexisting pollutional discharges. Therefore, they presently avoid them. This is because of the "potentially unlimited liability of post- mining treatment for any discharges that would remain after mining? (Pennsylvania Bulletin, 1985).

Jan 1, 1987

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998