Search Documents

By Hemendra N. Kalia

The target to double the coal production by 1995 presents a formidable challenge to the coal mining industry. The mines of future, probably will be located in relatively difficult geological environment because of the exhaustion of the well defined bedded and easily minable deposits. To compound the problems of mining industry will be the reliance of power plants need for coal. The coal must reach the power plants on schedule to avoid expensive blackouts and brown¬outs. It will be imperative that the mines operate without interruptions and at designed capacities. The parameters which have been traditionally responsible for the interrup¬tions of production are: breakdown of production machinery, labor management relations and geological anomalies. Of these three problems, solutions for the first two can be arrived at by developing procedures to correct the situation. A planned maintenance and preventive maintenance program will go a long way in minimizing the equipment breakdowns. Labor relations will eventually improve as the miners begin to enjoy long-term employment. However, with the geological problems, the situation will probably continue to deteriorate and would require careful planning to minimize the impact of geological problems on production and safety. Some of the geological aspects which interfere with production are: faults, washouts, slips and slickensides, water bearing overlying strata, impuri¬ties in the coal seam, and presence of expansive clays in the coal floor. The design of large capacity mines will have to incorporate the geological distur¬bances and mine through them it may become very uneconomical to abandon producing sections because of the presence of the geological anomalies. This paper discus¬ses the geological aspects of coal mining which should receive consideration from the inception of the mining ventures. Pertinent geological aspects are discussed to develop the data base which will aid in evolving safe and efficient mine layouts.

Jan 1, 1976

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By Theodore H. Eyde

In the southwest porphyry copper province, the virgin prospect with good copper mineralization cropping out has disappeared. Future discoveries will require an increasingly sophisticated arsenal of exploration techniques and concepts. One of the latter, stratigraphic analysis, is a technique which is often overlooked. A surprising number of exploration geologists still think of porphyry copper deposits as occurring wholly within intrusive bodies such as quartz monzonite or granodiorite. Disseminated copper mineralization, though genetically related to intrusive rocks, can occur within both the intrusive and the intruded rocks. At present, as much as 30% of the total copper produced from disseminated copper deposits in the Southwest originate from the intruded rocks rather than the intrusive. George M. Schwartz, in "Geology of the Porphyry Copper Deposits of Southwestern North America" points out that the host rocks at porphyry copper deposits include such diverse rock types as diabase, granite, limestone, dolomite, quartzite, skern, sericite schista, and others in addition to the more common monzonite, quartz-monzonite, and diorite porphyrys. Therefore, a porphyry copper can be defined as a disseminated copper deposit occurring either in or adjacent to a granitic-monzonitic-dioritic intrusive which can be exploited using bulk. mining techniques. The original definition of porphyry was originally applied to the early producers, such as Inspiration, Bingham, and Ajo, in which the copper mineralization occurred principally within the intrusive. A review of the geologic literature describing the porphyry geologic

Jan 1, 1971

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By A. R. Rule

As part of the Federal effort to help maintain an adequate supply of fertilizer minerals, the Bureau of Mines is conducting research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate. The rock varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current beneficiation by sizing, a flotation procedure was devised that included depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Application of the procedure to several different ores resulted in phosphate concentrates that ranged from 28 to 31 pct P20S in grade and from 60 to 70 pct in phosphate recovery.

Jan 1, 1977

By Kevin B. Doyle

Virtually all industries use sulphur in some form. About half of the world's production is used in the production of fertilizers. Sulphur is produced in one form or another in over sixty countries in the world. The major producing countries, in order of importance, are: U.S.A., Canada, U.S.S.R., Poland, Japan, France, Mexico, and Spain. Canada is the largest exporter of sulphur presently supplying about 30% of the world elemental sulphur export trade. It has held this position since 1968. World sulphur resources are virtually unlimited. Future world competition will come from Iraq and other Middle East countries as well as Central and South America.

Jan 1, 1978

By Galymzhan Karamyrzayev, Rashid Nadirov

Zinc ferrite ( ZnFe2O4) is a by-product of non-ferrous metal production and is considered a promising source of raw zinc. The most efficient way to extract zinc from its ferrite is via acidic extraction, specifically leaching by hydrochloric acid. A comparative study of synthetic zinc ferrite hydrochloric acid leaching in isopropanol, aqueous, and the mixed solvent was performed. Zinc ferrite was obtained by sintering a zinc and iron (III) oxide mixture. Crushed samples were subjected to leaching in 1 M HCl at 323, 333, and 353 K and pulp density of 1 g/100 mL. The dissolution of zinc and iron into solution in organic media reached 77% at 353 K, while in an aqueous environment this value was 65%. The activation energy of 70.0 kJ/ mol was found for the leaching process in an isopropanol environment, which is lower than that in an aqueous solution by 15%. The more efficient leaching effect of isopropanol is attributed to the lower dielectric constant of the alcohol which increases the affinity of chloride anions for zinc and iron cations at leaching.

Jun 5, 2022

By A. S. Macfarlane

Over the last few years, and especially the last few months, issues relating to Corporate Governance in industry in general, and the Minerals industry in particular, have become increasingly topical, as a result of a number of scandals and failures. The development of International and National Codes for the reporting of Mineral Resources and Reserves began some years ago, and has been followed by more stringent Listing Rules for the Securities Exchanges, as well as more standardised formats and protocols for financial reporting of assets and activities. More recently, some countries have adopted Codes for the Valuation of Mineral Properties, which have focussed on standardisation of valuation approaches to be adopted, and the qualifications of people deemed competent to sign off such valuations. This process has not been without criticism, the main criticism being the proliferation of local standards and regulations, which are often difficult to apply and regulate, or which are too prescriptive for multinational mining companies to deal with. In South Africa, these concerns have been recognised, while at the same time a need has been identified to establish a Code which could be applied to South Africa, and the African continent as a whole. Such a development would necessitate that the Code satisfies the needs of the continent, but in a global context. This global context has already been set by the activities of the International Organisation of Securities Commissions, the International Valuations Standards Committee and the International Accounting Standards Board. This paper explains the progress and process that has been established in South Africa for this purpose, and highlights the key issues which are open to public debate, so that the process is inclusive and transparent, whilst at the same time it is consistent with international time frames, and provides a deliverable product that meets the desired objectives.

Jan 1, 2004

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By Larry A. Lien

Membrane technology has been available for about 30 years, but has been used very sparingly within the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and element cleaning techniques have improved the reliability and robustness of membrane based systems. These improvements have expanded the potential to use this "new" technology to enhance critical recoveries of gold and silver in heap leaching operations or in the extraction circuit. Another opportunity for the mining industry will be to use membrane technology in new processes like controlling organic acids or ammonium thiosul­fate to enhance gold and silver extraction during leaching opera­tions. Finally, the most common use for membrane technology is for the control of mining water balance and acid mine drainage issues. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold or silver. Recent applications have been developed for spi­ral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operated on feed streams from 200° C to 3000 centipoise. Most recently, membrane based systems have been pilot tested suc­cessfully to purify solvents, like LIX. Opportunities exist to apply membrane technology to concen­trate gold and silver cyanide solutions with thin-film composite Reverse Osmosis (RO) membranes at elevated pH values above 10. Incorporating membrane technology could allow one to increase production without incurring additional expansion of the gold extraction side of the process. Furthermore, free cyanide is not rejected by the Reverse Osmosis membranes, but other inorganic salts are rejected 98+%, thereby, allowing an essentially ion free, except for the free cyanide, to be recirculat­ed back to the heap leach operation for enhanced extraction.

Jan 1, 1998

By Robert Dunne, John Angove

The physical properties of an ore body require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects. This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibil­ity, and to a lesser extent repeatability. The properties looked at were Impact Crushing Work Index, Abrasion Index, Bond Rod Mill Work Index and Bond Ball Mill Work Index. A number of testing laboratories throughout Australia and the US were utilised in the survey. The results showed up some interesting and important features of the procedures used, all of which have become accepted industry standards, and which had varying effects on the final result. Tests such as the rod and ball mill indices would appear to have reasonably robust procedures which allowed for the determinations of the respective index without the introduction of significant variations, although there were indications that variations could occur. The other tests gave a sufficiently different picture to be able to suggest that an argument could be made for a more intensive investigation to be undertaken, with the possible outcome that a modified test procedure or an alternative test is required.

Jan 1, 1997

By A. G. Mayton, L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors' response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle's kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986 ). The action of the cable reel adjusts well to this pattern. The proposed shuttle car's motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I” pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern's importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop

Jan 1, 1991