Search Documents

By Frank W. Bowdish

Studies of sulfidization and flotation of chrysocolla involving the use of pH and sulfide ion instruments, a Zeta meter, microflotation techniques, and sensitive determinations of adsorbed sulfur have given new insight into the mechanism of the process. Factors that affect the recovery of sulfidized chrysocolla by flotation appear to be the pH at which it is sulfidized, and certain alterations of the surface that occur during aging after sulfidization. Such aging results in increased recoveries. The surface charge, as measured by electrophoretic mobility, of chrysocolla shows an unexpected negative increase as pH values are changed from 6.0 to about 4.5, and this appears to be correlated with increasing sulfur adsorption and flotation recovery over the same or even wider pH ranges.

Jan 1, 1970

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

By J. McCreedy

The Ontario Division of The International Nickel Company of Canada, Limited, operates five underground mines and one open pit on the rim of the Sudbury Basin located in the Province of Ontario, 230 miles northwest of Toronto. Four of the mines, Frood-Stobie, Creighton, Murray and Garson, lie on the South range of the Basin within a 10-mile radius of the City of Sudbury; the fifth mine, Levack, is on the North range, about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, the principal minerals being pentlandite and chalcopyrite. Other elements recovered from the ores in varying quantities are platinum, palladium, ruthenium, iridium, rhodium, cobalt, selenium, tellurium, iron, sulphur, gold and silver. In 1962, the total underground ore production was over 10,800,000 tons which was mined mainly by blasthole and caving methods with the remainder by cut-and-fill, square set, and undercut-and-fill techniques.

Jan 1, 1964

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By E. M. Williams

The U.S. Bureau of Mines recently conducted a limited-scope study on the use of lineament analysis and electromagnetic geophysics to better identify the surface expressions of faults at the Cimmaron Mine near Raton, NM, an operating longwall mine in the York Canyon mine complex. Two normal faults were encountered by the mine, one during gate road development and drilling and another only through drilling. The potential ground control problems and offsets associated with these faults will severely impact long-range development plans, so it is essential to know the lateral extent of these faults within the coal reserves. The surface topography at the site is fairly rugged, yet outcrop exposure is poor. There is no obvious visible geologic evidence to indicate that the faults identified at depth extend to the surface. Both the geophysical and remote sensing techniques provided information on the presence and extent of important geologic structures which could not be gained just from drilling and surface outcrops. The geophysical surveys also were invaluable in confirming the presence of subsurface geologic structures in the vicinity of the lineaments assumed to be associated with the faulting.

Jan 1, 1995

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Richard Minnitt, Philippe Renard, Christina Dohm, Winfred Assibey-Bonsu, Matthew Aboagye, Julien Straubhaar, Mahlomola I. Mabala

The application of multiple point statistics (MPS) in oil studies has gained traction over the years; however, the use of MPS in mineral resource estimation and classification is still limited. This is despite MPS’ ability to deal with complex and heterogeneous geology better than the commonly applied two-point based methods. The availability and choice of a representative training image (TI) are often cited as the main challenge holding back MPS’ application in mining geostatistical studies. On the other hand, the general approach used in mining whereby early focus is on higher grade areas and lower grades are planned to be mined later presents a massive opportunity for the development of representative TIs. Mined-out areas provide large amounts of historical data that can be used to develop training images or training datasets that can be used to estimate in mining extension areas (often lower in grade), provided low grade areas are underpinned by similar geology analogue. This approach will enable more robust estimates in mine/pit extension areas for both high- and low-grade extensions than with traditional two-point geostatistical methods.

Jun 25, 2023

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By R. J. Sweigard

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on the evaluation process. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mine. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1983

By Rami Abousleiman, Gabriel Walton, Sankhaneel Sinha

"Although conventional coal mine designs are conservative regarding pillar strength, local failures such as roof-falls and pillar bursts still affect mine safety and operations. Previous studies have identified that discontinuous, layered roof materials have some self-supporting capacity. This research is a preliminary step towards understanding these mechanics in coal-measure rocks. Although others have considered broad conceptual models and simplified analogs for mine roof behavior, this study presents a unique numerical model that more completely represents in-situ roof conditions. The discrete element method (DEM) is utilized to conduct a parametric analysis considering a range of in-situ stress ratios, material properties, and joint networks to determine the parameters controlling the stability of single-entries modeled in two-dimensions. Model results are compared to empirical observations of roof-support effectiveness (ARBS) in the context of the coal mine roof rating (CMRR) system. Results such as immediate roof displacement, overall stability, and statistical relationships between model parameters and outcomes are presented herein. Potential practical applications of this line of research include: (1) roof-support optimization for a range of coal-measure rocks, (2) establishment of a relationship between roof stability and pillar stress, and (3) determination of which parameters are most critical to roof stability and therefore require concentrated evaluation.INTRODUCTIONRecent studies on pillar design have suggested that the assumptions utilized in traditional methods such as tributary area theory (TAT) (i.e. overburden has no self-supporting capacity, infinite pillar array, and CHILE material properties) are invalid in many geo-mining conditions (Esterhuizen, Mark, and Murphy, 2010; Frith and Reed, 2017). Although TAT is conservative with respect to pillar loading, and mine fatalities have steadily decreased since 1990, roof-falls and pillar bursts still occur and injure hundreds of miners per year (Mark, Pappas, and Barczak, 2011). Even though large-scale global mine failure has not occurred in a US coal mine since 2007, the mechanics of global and local stability as governed by the relationship between geologic parameters, mine geometry, and engineering design are still not well-constrained.Numerical methods are a highly effective tool that can be used to gain further insight into these relationships. When using such an approach, calibration to existing empirical relationships is imperative to ensure that numerical model results are realistic. In this study, we utilize the discrete element method (DEM) approach in Itasca’s Universal Distinct Element Code (UDEC v. 6.0) (Itasca, 2010).DEM accounts for explicit separation and contact of individual deformable blocks (Jing, 2003) and captures how discontinuities can affect system behavior. Discontinuous and anisotropic rockmass properties are typical features in coal-measure rock which contain various horizontal (bedding) and sub-vertical (joints) fractures depending on their depositional environment, diagenesis, and historic and current stress states."

Jan 1, 2019

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!&apos; is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By H. Kiyama

In order to further elucidate the mechanisms involved in autogenous grinding, the fracture of rock specimens in free-fall impact was studied using the theory of elasticity. Stress distributions in rock specimens under various conditions of impact were analyzed and the conditions for failure were examined in relation to the compressive and tensile strength of rock. The energy equation derived for autogenous grinding coincides basically with Lewis&apos; generalized formula or Oka and Majima&apos;s formula, and it is sufficiently general to incorporate all of the three older theories, viz; those of Rittinger, Bond and Kick.

Jan 1, 1972

By J. S. Hastings

Tertiary calc-alkalic to alkalic rocks of the Little Rocky Mountains in north-central Montana host low-grade heap-leachable gold-silver deposits being mined by Pegasus Gold Corporation. Total production from 1884 through 1985 is estimated at 22,625 kilograms (727,414 ounces) of gold. This includes 10,774 kilograms (346,400 ounces) recovered by Pegasus between 1980 to 1986 from 20,318,000 tonnes (22,396,000 tons) of ore grading 0.960 grams of gold per tonne (0.028 ounces per ton). Silver production during this latter period was 24,556 kilograms (789,500 ounces), but reliable silver statistics prior to 1980 are not available. Ore reserves as of January 1, 1986, were estimated to be 35,380,800 tonnes (39,000,000 tons) grading 0.720 grams per tonne (0.021 ounces per ton). Present ore production is 5,533,920 tonnes (6,100,000 tons) per year at a 0.45 to 1 waste to ore strip ratio. Current annual metal production is about 2,644 and 5,288 kilograms of gold and silver respectively (85,000 and 170,000 ounces of gold and silver respectively). The Little Rockies were formed by a calc-alkalic to alkalic magma penetrating through the Precambrian basement into the overlying Paleozoic and Mesozoic sedimentary rocks. This intrusive center is Dart of the Central Montana Alkalic Province, a region comprised of twelve separate intrusive centers aligned in a northeast trending belt measuring 200 by 400 kilometers (124 x 248 miles). The ore deposits are structurally controlled epithermal systems which vary from deeper narrow veins to shallow, wide, low-grade stockworks, breccias and intensely fractured "sheeted" zones. The shallow types are now being exploited. Primary mineralization consists principally of gold and silver associated with pyrite, native gold and silver, sylvanite, calaverite, and hessite. Alteration is broadly classified as weak argillic. Pyritization, kaolinization, silicification and feldspathization are the dominant forms of alteration. Fluorite is a common hydrothermal gangue mineral.

Jan 1, 1987

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By S. Chander

The effect of sample storage in argon and in air on kinetics of oxidation of pyrite from a coal source was studied using accelerated weathering test in laboratory columns. Prior to the weathering tests the samples were crushed, ground, and stored for various time periods in argon and air. The results showed a dramatic difference in the rate of oxidation of the aged samples. The differences were interpreted based on the hypothesis that the aging of pyrite led to the formation of surface coatings which changed with time. The significance of these results in pyrite/reagent interactions in flotation and in evaluating the acid mine drainage potential of pyritic waste materials is discussed.

Jan 1, 1993

By Thomas H. Ferrigno

Modern Plastics (July, 1983) reported that about 2.2 million tons of mineral fillers were expected to be consumed by the plastics industry that year, of which 7096 was limestone derived. The combination of fillers and polymers is called a composite and, in the more general sense includes continuous and discontinuous components in a matrix. The only significant technical advance in the fillers industry has been the greater general availability of surfied (Ferrigno 1959), an acronym for surface modified, fillers. The many reasons for this occurrence will be given in detail later, but the primary reason lie with differences between inorganic filler surfaces and the polymers which bind them together to form the composite. Minerals and glasses (fiberglass, fly-ash and beads) have surface tensions in excess of 200 dynes/cm, whereas organic materials have surface tensions less than 75 dynes cm. Water has a surface tension of 72 dynes/cm and is always present as an absorbed layer on high surface tension materials to reduce the surface tension. Although almost any organic liquid or polymer has a surface tension low enough to displace the water layer, the highly polar nature of filler surfaces requires highly polar agents to produce a permanent effect, and frequently the water is so tightly bonded or so much more active that the displacement is temporary. Furthermore; the water layer causes tiny particles to adhere to each other (agglomerate) to make sepaartion or dispersion of the individual particles very difficult. The solution to these problems is then to form a chemically bonded layer on the filler surface similar to that of the polymer so that immediate wetting, dispersion and uniform distribution of the filler particles is obtained.

Jan 1, 1985

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024