Search Documents

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

By R. Sellaro, E. Sarver

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While many efforts have been made with the aim of understanding the mass-based concentrations and silica contents of respirable dusts under a variety of mining conditions, little research has been completed in characterizing dust at the individual particle level (by composition, size and shape). This study employed scanning electron microscopy with energy dispersive x-ray (SEM-EDX) to analyze dust samples collected from an underground coal mine in Central Appalachia. The results indicated that particle characteristics can vary widely between locations, though many trends might be explained based on knowledge of mining conditions. A continuous personal dust monitor (CPDM) was also used during the collection of some samples to determine respirable dust concentrations, which were compared against estimated concentrations based on the particle-level analysis.

Jan 1, 2014

In 1991, US mine production of barite decreased 3.4%. Barite consumption, sold or used by grinding plants, decreased by 11.7%. Imports also decreased by 15.4% over 1990. World mine production increased I%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, increased 3.3% according to the Bureau. The declared value c.i.f. US port of all imported crude barite during 1991 increased from $40.61/t ($36.84/st) in 1990 to $42.35/t ($38.42/st), the Bureau stated. Nevada was the leading producer of barite with 78% of the total, followed by Georgia and Missouri. It is estimated that 75% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 93% was used in drilling fluids. The remaining 7% was in the non-oilfield sector, including barium chemicals and fillers in paper, plastics and glass. Tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1990. The average number of rotary rigs operating was 860. That was 14.9% less than the 1990 average of 1010 in the US. Crude barite imports were 138 kt (152,000 st) less than 1990 or 15.4%. Imports accounted for 70% of the (ap¬parent) barite consumed in the US. During 1991, China continued to be the leading exporter of crude barite ore to the US with 85.1 %. India followed with 14.8%. About 97.5% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 56.7 to 46.2 kt (62,500 to 51,000 st) 1991. Mexico was a major exporter to the US, accounting for 75.3% of the total ground barite imports. Canada shipped 23.7%, while other countries accounted for less than 1 %, primarily for the nonoilfield market. During 1991, the number of grinding plants supplying the drilling fluids market along the Gulf Coast was reduced from 12 to 10. Baroid Drilling Fluids completed its mining program at the Rossi Mine near Dunphy, NV.

Jan 1, 1992

By Bernard E. Weichman

The oil shales in the Piceance Creek Basin of northwest Colorado occur in the Parachute Creek member of the Green River formation. The oil shales were deposited in a unique environment of deposition which caused the mineral nahcolite (NaHC03) to be precipitated within the oil shales. Post-depositional tectonics resulted in extensive fracturing of the Middle Zone of the Parachute Creek member, and to a lesser degree portions of the Lower Zone, which allowed percolating ground waters to dissolve the nahcolite in the fractured portion of the oil shale beds which is characterized by broken porous oil shale, certain beds of which have collapsed into rubble and debris. The extent and porosity of the Leach Zone aquifer is dependent upon the percentage of kerogen and nahcolite originally deposited in the oil shale. Any oil shale development program in the Piceance Creek Basin of northwest Colorado will need to be preceeded by an extensive study of the Leach Zone in order to determine the effects on a mining program.

Jan 1, 1973

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By Joseph Cervik

Common methods of controlling gob gas in U.S. nines are by means of ventilation of gob areas and gas drainage through surf ace boreholes. Costs of drilling surface gob holes increase as deeper coalbeds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States, This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1979

By David D. Lambert

REE analyses of cumulate plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma can- not be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data is more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE bearing sulfides of the J-M Reef are associated with such a re- appearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultramafic zone of the complex.

Jan 1, 1981

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By P. Dhar, H. R. Kota, M. Thornhill

A very high-grade calcite deposit located in northern Norway consists of CaCO3 ore with minor silicate and sulphide impurities. Cationic (Tallow-1,3-diaminopropane, Duomeen T) collector has been used in the purification of calcite by flotation with an aim of achieving calcite concentrate for its use in value-added products in a variety of industries. The feasibility of sulphide flotation from calcite by this cationic collector has been initially judged from Hallimond flotation and zeta potential on pure mineral systems and the results illustrate the removal of sulphide from calcite ore at neutral pH region. The adsorption mechanism of diamine on both the sulphide minerals was found to be the same by zeta potential studies. The variations in zeta potential are in good agreement with the adsorption of diamine molecular and ionic species as a function of pH. FTIR studies also showed the adsorption of diamine species in agreement with the zeta potential and Hallimond flotation results. Furthermore, the removal of sulphide impurities with selective flotation by diamine collector was performed in bench-scale flotation with the calcite ore and the results indeed showed that the calcite concentrate could meet the quality requirements for its use in the paper industry for coating and filler purposes.

By Sam S. Arentz

Storm King Mines began with the concept that the resource potential of thick and steeply pitching seams of the Grand Hogback region of Colorado could be mined profitably. Two large tracts of private land (fee coal) were acquired; approximately 23.8 km2 near Glenwood and 16.2 km2 near Meeker. Figure 1. Although both properties have substantial coal reserves, one has several distinct advantages in developing a competitive mining operation. Table 1 illustrates these advantages. Among the most important considerations from an economical point of view are proximity to railroad, highway, labor force, quality of coal, seam thickness, and source of water. As can be seen, Storm King Mines' property is adjacent to the main line of the D & RGW Railroad, 1-70, and the Colorado River. The cities of New Castle, Glenwood Springs, Silt, Rifle, Carbondale, and Parachute are within short commuting distances and have available skilled labor.

Jan 1, 1983

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By K. W. Harris, K. A. Perry

Reserve depletion in Central Appalachia is continuously creating unique ground conditions for underground coal mines with many of these difficult environments directly attributable to multiple seam mining and/or deeper overburdens. While many empirical studies have been performed in an effort to improve understanding of these problems along with potentially improving safety and extraction, many of the difficulties encountered lie outside of the normal realm of expected behavior. This is often the case when mining in bump prone ground, where additional concerns are introduced and design buffers are warranted. The boundary element software LaModel was used to study three bump events in a deep-cover, multiple-seam reserve located in Harlan county in the Kentucky region of Central Appalachia. This region is notoriously bump prone due to significant areas of deep cover, the presence of strong to massive lithology (such as sandstone), and an extensive history of underground mining that increases the probability of multiple seam interactions. Multiple seam interactions are best understood with respect to site-specific parameters, including both the geological and geometrical components of interburden, overburden and mine workings. Initially, empirical-based approaches (ARMPS/AMSS) were used when attempting to back-analyze the bump events. However, it was recognized that a more detailed investigation was necessary to understand the fundamental causes/conditions associated with the bump events. Consequently, the LaModel study resulted in a mine-specific calibration method for the reserve. With this method in place, enhanced bump prediction throughout the reserve is expected, such that the stability, recovery and safety of future mining may be improved.

Jan 1, 2014

By Yvon H. Poirier

Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976. Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen percent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March '80, Sidbec-Normines use coke addition as a current operation. This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port-Cartier pellet plant.

Jan 1, 1982