Search Documents

By D. L. Boreck

With increasing land development, the potential of fatalities from abandoned mine shafts increases. To minimize potential liability, shaft closure should be a critical part of mined land reclamation. The Bureau of Mines is conducting research into using lightweight foam concrete in sealing abandoned coal mine shafts. A demonstration seal consisted of a 3m thick foam concrete plug to provide lateral stability inside the shaft. A high density concrete cap provided load-bearing capacity for a 100-year service life. The USBM has also completed research into changes in foam concrete when it is pumped or dropped from different heights. It is concluded from the research that foam concrete can undergo significant air loss with pumping or dropping. This foretells significant changes in the characteristics of the concrete as well as an increase in the weight and cost of the in-place concrete seal. When using foam concrete to seal abandoned mine shafts, care must be taken to minimize air loss during placement.

Jan 1, 1994

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By W. B. Weston

To mining people who have experienced the tremendous expansion of existing operations and the development of new properties over the last several years we do not have to point out the difficulties in hiring skilled equipment operators. To those of you who have opened operations in some of the more remote places in the world this is not just a difficulty. It is an impossibility. Your only recourse has been to try and train whatever manpower has been available. Depending upon your success in training, the next problem has been to keep them. On todays modern equipment, the skill of the operator remains as the greatest single variable affecting the performance of the machine. On a blast hole drill, for example, a skilled operator will get good production footage, acceptable bit life and minimal machine downtime The unskilled operator will not only fail to get the acceptable production footage but all too frequently this failure is coupled with low bit life, high repair costs and excessive machine downtime. Even between experienced operators, on identical machines, in the same kind of material we find significant variations in performance. It is, therefore, the skill of the operator, not just his experience, which makes the difference. The problem, as presented to us by our customers, has been to find a way for the unskilled man, with minimal training, to match the performance of the most skilled and experienced operator. The obvious answer is automation.

Jan 1, 1970

By Yuting Xue, Gamal Rashed, Zoheir Khademian, Morgan Sears

Mining has been recognized among the most hazardous industries in the United States, despite the significant reduction in injury and fatality rates over the past century. This study focuses on the ground-fall incidents classified in the Mine Safety and Health Administration (MSHA) database as “fall of roof, back, or brow from in-place” and “fall of face, rib, pillar, side, or highwall.” The main objective of this study is to conduct a comprehensive statistical analysis of the reported ground-fall incidents from 2010 through 2019 including both coal and metal/non-metal mines. Since most of the ground-fall injuries and fatalities occurred in underground coal mines and were attributed to falls of roof and rib, an additional analysis was directed to evaluate roof- and rib-fall incident trends in underground coal mines associated with the mining method, coal-seam thickness, mine size, and the seasonal effects.

By Gordon J. Hughes

The ldaho Cobalt Belt represents a unique geologic environment containing some of the largest known reserves of cobalt in the United States. Stratabound cobalt-copper-gold deposits formed within a sedimentary basin that was generated by the rifting of an Archean cratonic block. Host rocks for these deposits are the Early to Middle Proterozoic Yellowjacket Formation comprising a suite of clastic sediments, volcaniclastics, and mafic tuffs that accumulated in the intracratonic rift basin about 1.7 b.y. ago. Rifting was probably initiated during a regional heating and doming event that may date back to 1.8 b.y. ago. During this time, other rift basins were likely to have formed in the region. They probably represent the precursors of a much larger depositional environment having characteristics of an Atlantic- type or passive continental margin where younger formations of the Belt Supergroup were deposited. The Yellowjacket Formation has been subdivided in the Idaho Cobalt Belt into three genetic units representing various subenvironments of a deepwater clastic fan complex. A northwest- trending deep-basin structural trough accumulated fine-grained muddy sediments that were periodically interrupted by distal turbidites of the subaqueous fans. Subsequent progradation caused the deposition of coarser-grained clastics of the more proximal portions of the fan complexes. Submarine fan lobes were built across northwest-trending tectonically active basin growth faults. These in-basin structures caused a great deal of penecontemporaneous deformation within the Yellowjacket sequence. Northeast-trending fault zones formed an orthogonal set of fractures that controlled the shape and size of sub-basins, and were also an influence on lateral migration of dominantly fine-grained clastic material. The eruption of mafic tuffs at about 1.7 b.y. ago added a new component to the Yellowjacket sedimentary sequence. Around the Blackbird mine area these tuffs commonly occur either near the base or within some of the sandier sequences. Since most of the sand influxes were largely controlled by basinal tectonism, the tuffs were probably erupted during tectonically active periods of basin development. The dynamic nature of the sedimentary environment probably caused much of the tuffaceous component to be mixed with other clastics and even resedimented as volcaniclastic material. In time, the change to a higher energy sedimentation regime resulted in such a dramatic clastic dilution of the tuffs that they could not survive in the areas of the vents, and, if present, they must have been distributed elsewhere in the basin.

Jan 1, 2013

By W. Clark Ashby

Trees are an essential ingredient of sound reclamation in nearly all surface mining regions. There are, however, possible problems in current reclamation regulations and practices which need to be evaluated and remedied. Recognition and accomodation of growth requirements for trees and other plants will greatly increase reclamation success. Surface mining encompasses a series of processes from a pre-mining baseline study to bond release following revegetation. Land owners, and society, have a great interest in subsequent plant growth on reclaimed areas and in future land values.

Jan 1, 1981

With unprecedented worldwide growth and increasing global demand for energy expected to swell by 60 per-cent in the next two decades, mining matters as much now, if not more, than it ever has. This was the consensus at the 110th Annual National Western Mining Conference presented by the Colorado Mining Association, Feb. 12-14 at the Westin Hotel in Denver, CO. The role of coal ? America?s most abundant energy source ? the future of uranium and its possible resurgence in the energy marketplace, the skyrocketing value of gold as well as the issues of health, safety, climate change, legislation and government?s role in mining were all discussed during the three-day conference that operated under the banner of ?Mining Matters.? Barbara Filas, chairperson of the 110th National Western Mining Conference, president of Knight Piesold Co. and former SME president, welcomed the record crowd with an inspiring speech in which she pointed out that although ?most normal folks don?t know what role mining plays in their everyday life, mining does matter. ?Our industry,? she said, ?matters to Colorado. It matters to Colorado because it is a $3-billion industry. It matters to the 13,000 people who are employed directly or indirectly by the industry and it matters to schools that receive more than half of the royalties that are generated by mining.? During discussions of mining?s place in Colorado, the western United States and the world, special attention was paid to coal, uranium and the future of energy. ?It is time to rethink our perceptions about coal,? said Mark A. Smith, president and chief executive officer of Chevron Mining Inc. He spoke during the opening reception in a presentation titled, ?Coal to Liquids: Bridging America?s Energy Gap.? Although coal is America?s most abundant, and cheapest energy source, it is also one of the most scrutinized because of the pollution it causes and recent, and heavily publicized, tragedies that have claimed the lives of some who mine it.

Jan 1, 2008

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983

By I. E. Odom

The physiocemical properties and industrial uses of the clay mineral montmorillonite are reviewed. Montmorillonite is the most abundant species of the smectite clay mineral group and is the predominant mineral composing bentonite deposits. The crystal structure, chemical composition, exchangeable ion type, and small crystal size are responsible for several unique properties, including a large chemically active surface area, a high cation exchange capacity and interlamellar surfaces having unsual hydration characteristics. The type of exchangeable ion Na, Ca and/or Mg has a major influence on industrial and chemical uses of montmorillonite because of their hydration characteristcs. Natural occurrences of Na montmorillonite in commercial quantities are geographically limited, but Ca-Mg montmorillonite deposits are known world wide. Foundry, well drilling, pelletizing and civil engineering constitute the major uses of montmorillonite, but the total array of uses of montmorillonite exceeds that of any other mineral.

Jan 1, 1986

By V. F. Hollister

Computer programs developed as part of the PROSPECTOR project at SRI International can indicate where the highest grade hypogene copper occurs in porphyry copper prospects. The programs are useful in selecting drilling targets in untested porphyry deposits. Because of mineralogic, structural and lithologic variations in porphyry-type deposits, three distinct computer programs have been constructed; however, this paper considers only the stockwork type in homogeneous rock (similar to the Lowell and Guilbert model). The programs represent models in the form of inference networks that utilize the mineralogic, alteration, lithologic, structural, geochemical and geophysical data normally collected prior to a drilling decision. One example of an application of the PROSPECTOR program for a stockwork-homogeneous porphyry is given: Island Cooper in British Columbia. Computations based on the surface geologic, geochemical and geophysical data for Island Copper clearly disclose the best hypogene grade of the deposit. Other deposits were tested in the programs as well, and in each case PROSPECTOR programs indicate the region with the highest hypogene grade.

Jan 1, 1983

By J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Company to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the Company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received substantial attention in recent years. A Company guideline that no coal shipment shall exceed any contract or company-imposed coal quality specification has been successfully implemented. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed. Background Surface coal mining of subbituminous C rank coal in the Cillette. (Campbell County) Wyoming area has become increasingly competitive during recent years. Prior to 1974, one small surface mine produced coal for local consumption. During the last ten years, 13 new surface coal mines have been constructed. Coal production from Campbell County, Wyoming totalled 88 million short tons (79.8 million metric tons) in 1983, the majority being shipped to electric utilities in the central and southern United States via unit trains having a capacity of 10,000 short tons (9,072 metric tons).

Jan 1, 1984

By Terry R. Guilinger

A minitest of the new potassium chloride-potassium carbonate two-stage in situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing carion-exchange reactions. The test a1 so indicates permeability anisotropy and the existence of disturbed flow fields. The research was partially funded by the U.S. Bureau of Mines.

Jan 1, 1984

By Lorraine B. Burgin

The extensive lead time to develop most Arizona copper deposits commenced with initial production efforts before the turn of the century, when the first attempts were made to recover gold and silver and later copper from the high-grade vein deposits of the territory. Each of these discoveries, prospects, and early operations had its own lead time and life cycle as economic production was attempted. Because prices of the metals fluctuated and the higher grade material was depleted, economics forced operations to close and companies to fail. Renewed interest in the property because of improved conditions, different interpretation of the geologic structure, or new promotional ability frequently resulted in the formation of yet another company to finance the exploration and, hopefully, the development of the property. This cycle of renewed activity and subsequent abandonment was and is common, accounting for many lead times and for the long period of time from the initial location of claims to large-scale production. In order to gain a perspective on the lead-time interval necessary to achieve development of a large-scale operation, the histories of several major Arizona mines were examined, rather than a simple listing of discovery and production dates of many mines to arrive at a statistical average. The Miami, Castle Dome, Copper Cities, San Manuel, and Twin Buttes properties were studied, and as much data as possible obtained on the Pinto Valley, Esperanza, Sierrita, Pima, and Mineral Park-Ithaca Peak properties.

Jan 1, 1974

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By Eugene C. Robertson

The exchange of heat from wall rock to ventilating air was studied in a cross-cut driven through fresh rock on the 4600 level of the Kelley Mine, Six- teen thermocouple probes, 10 inches long, twenty-three probes, 7 feet long, and five probes, 50 feet long, were emplaced in the walls soon after blasting and wall -rock temperatures were monitored intermittently over a two-year period to determine heat loss from the wall rock. Temperatures, humidity, and velocity measurements were made of the air at the same times to determine heat gain. An important but less well-defined variable was the heat transfer by water entering the crosscut from fractures and leaving in the ditch. The balance of heat in and heat out at each probe station is within an acceptable range. Theoretical and empirical models for heat flux into a cylindrical opening fit the data reasonably well, also.

Jan 1, 1970

By Jan M. Andersson

This paper will discuss the background information about rock cutting tools used for soft ground excavation, their history and evolution. A brief review of the current state of the art manufacturing technology will be presented and some parameters related to the material used in the drag and conical type pick cutters and their impact on their life and performance will be explained In addition, the selection procedures for choosing the right bit for excavation of a particular geological formation will be reviewed A set of guidelines will be provided for initial selection of the tools for various machines and rock formations. The methods for estimation of the tool life in various materials and the influencing parameters along with limitations of the rock cutting tools will be discussed as well.

Jan 1, 1998

By H. J. Bickel

This paper is concerned with general concepts and statistical devices used in projecting overall energy requirements. Particular emphasis is given to the use of individual end- use markets as an approach to developing future overall energy requirements, and translating these requirements into fuel consumption.

Jan 1, 1962

By J. R. Goode

The first part of this paper comprises a general discussion on refractory gold ores and their mineralogy processing methods now in use are reviewed and test procedures for the important methods are discussed. Factors determining the selection of a process are outlined. The paper includes a survey of production plants using pressure oxidation, roasting and biological oxidation to process refractory ore. The status of processes under development is briefly reviewed.

Jan 1, 1993

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985