Search Documents

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

ITEC Environmental Colorado has begun reprocessing the tailings from old mining sites near Boulder, CO. And if the technology behind ITEC's pilot project at Gold Hill proves successful and profitable, the company plans to launch similar reprocessing operations in other parts of the state. The pilot project is under the watchful eye of state and federal authorities. They hope the technology becomes the answer to cleaning up old mining sites throughout the West. Remining and environmental cleanup on an economic basis, then, are ITEC's hopes in one the most environmentally conscious counties in the state. Clean up the mine dump sites and recycle the land, for a profit. In June 1998, ITEC Mineral Inc., ITEC Environmental Colorado's Canadian parent, acquired the Gold [ ] Hill Mill facility in Boulder County. Included in the acquisition was 4.4 hm2 (11 acres) containing the Gold Hill Mill and 283 hm2 (700 acres) of additional properties adjacent to the facility. ITEC estimates that there are about 910 kt (1 million st) of dump rock in the area. That is enough to make the operation viable. ITEC will sell the metals recovered through its reprocessing operations. However, due to low metals prices, ITEC is not expecting to make much money on the recovery of precious and base metals. Instead, the company plans to resell the reclaimed land for residential and commercial development or open space. The Gold Hill Mill site is the first of 17 sites in Colorado that ITEC Mineral hopes to clean up and recycle the land. Most notable among the sites is the historic Central City/Black Hawk mining district, which ITEC believes holds considerable potential. The Gold Hill Mill is located 14 km (9 miles) west of the city of Boulder and less than a half mile from the small town of Gold Hill. The mill was. last operated in 1992. The operation was forced to close that year due to environmental and cash flow problems. Gold Hill is in the middle of a region with more than 32 Mt (35 million st) of mine tailings. Independent geologists have' established the average grade of the Gold Hill mine tailings to be 4.5 to 5.3 g/t (0.13 to 0.155 oz/st) of gold and 28 to 44 g/t (0.83 to 1.29 oz/st) of silver. According to these studies, the Gold Hill mine tailings are five times richer in precious metals than the tailings of the Norebec Manitou property in Canada that ITEC is also remining, reclaiming and restoring. Upon acquiring the mill, ITEC undertook a refurbishing program that included adding a second ball mill. This increased the Gold Hill Mill's capacity to 180 t/d (200 stpd). The operation employs 15 people. "The Gold Hill Mill site will demonstrate the efficiency of our integrated remining, reclaiming and restoration process," said Maxine Stewart, president of Denver, CO -based ITEC Environmental. "The abundance of similar mine sites in Colorado presents a number of opportunities to bring the benefits of the ITEC system to other communities around the state." Holly Huyck is technical advisor to the Clear Creek Watershed Advisory Group. She said: "ITEC is cleaning up an orphan mine site that otherwise would continue to contaminate the Boulder Creek watershed with acid and excess metals. This is a win-win situation: ITEC gains marketable minerals while it reclaims mined land and helps to improve the watershed."

Jan 1, 1998

By Tim Neil, O&apos

Large is the applicable adjective here. The largest hydraulic shovel in the world, the largest copper mine in the world, the largest copper producing company in the world. The O&K RH 300 hydraulic excavator has been put into service to move overburden and mine ore at the Chuquicamata open pit mine of the Chilean state copper mining company, Corporation Nacional de Corbre de Chile (Codelco). A large shovel: Equipped with a 26-m3 (34-yd') rock shovel, the RH 300 is able to fill a 170-t (187-st) truck in three passes with cycle times of 30 seconds. A large mine: At present, the Chuquicamata pit is 4 km (2.5 miles) long, 2 km (1.2 miles) wide, and 520 m (1700 ft) deep from rim to bottom bench. The current 450 kt/d (496,000 stpd) of material mined will increase to 600 kt/d (661,000 stpd) when the expanded production rate is reached in 1989. (Chuqui Expansion details, p. 20). A large mining company: Codelco's total output from its two open pit and three underground copper mines is more than 1.1 Mt/a (1.2 million stpy) of copper. This makes Codelco by far the largest copper producer in the world. It accounts for about 15% of the Western World's copper requirements. Chuquicamata is located in the hot and arid Atacama desert of northern Chile. The mine is located 240 km (150 miles) northeast of the port city of Antofagasta. Mine elevation is 2700 m (8850 ft). Chuquicamata's known reserves of oxide and sulfide ores amount to more than 450 Mt (496 million st) of contained copper. There are also reserves of more then 1.4 Mt (1.5 million st) of contained molybdenum. Originally, Chuquicamata was a rail pit. The shovels loaded rail cars hauled by locis on tracks along the benches. During the 1970s, the rail transport was replaced by truck haulage. Crushing and conveying rock waste in the pit is the latest step in the continuing evolution of more productive and economical methods of materials movement. In 1990, the in-pit crushing plant will be in operation. The waste will be mainly transported out of the pit on belt conveyors rather than trucks. The system will incorporate a 9.6-kt/h (10,600-stph) semi-portable crushing station, a 14-km (8.7-mile) conveyor using 1.8 m (6 ft) wide heavy duty belts, and a tripper-spreader to stack the waste dumps. Since Chuqui went into production in 1915, more than 2.5 Gt (2.8 billion st) of material has been excavated. This includes nearly 1.7 Gt (1.9 billion st) of ore from which some 16.4 Mt (18 million st) of copper has been recovered. The Chuquicamata porphyry type ore body is an altered and fractured intrusive granodiorite or quartz-monzonite porphyry that carries the mineralization. The action of ground water on primary sulfide minerals in geo¬logic time has created oxide ores and a zone of secondary enrich¬ment. The oxides occur above the sulfide zone and are also mixed with the upper parts of the latter. At Chuquicamata, the current grade of 1.5% copper is expected to decline to about 1% by 1995. To maintain metal production at cur¬rent levels, it will be necessary to increase ore production rates by about 50%, as mentioned, to 153

Jan 1, 1988

BP Minerals America (BPMA) has completed its $400 million modernization of Kennecott Utah Copper's Bingham Canyon mine. Modernized facilities include the in-pit crusher, conveyor, ore storage area, concentrator, ore pipe-line, and tailings pipeline. With modernization, Kennecott will achieve substantial cost reductions. Bingham Canyon is now one of the lowest cost copper producers in the world. And the mine will continue to provide jobs and income in Utah for another 30 years or more. The Modernization Project began in February 1986. The work took 33 months. In late 1987, the construction force peaked at 1100 workers. Kennecott Utah Copper now employs a permanent work force of 2100 employees. Less equipment and more efficiency The modernization work has increased the scale of the facilities that transport and process copper ore. A large, continuous transport system has replaced multiple haulage units. Fewer but larger pieces of equipment have replaced many crushing, grinding, and flotation units. The result is less maintenance, fewer employees, and improved metal recoveries. About one-third of the $400 million modernization project is directed at improving ore movement by eliminating rail transport. The new concentrator accounts for the remaining two-thirds of the modernization investment. The modernized plant was started up in stages. In February, ore was fed to the crusher. By the end of March, the three grinding lines were operating and the flotation circuit was producing copper concentrate. In July, the design through-put rate of 70 kt/d (77,000 stpd) was reached. October saw the achievement of targeted metal recoveries that corresponded to the fully modernized operation. It is estimated that Bingham Canyon will annually produce 181 kt (200,000 st) of refined copper, 9.3 t (300,000 oz) of gold, 71 t (2.3 million oz) of silver, and 5.4 kt (12 million lb) of molybdenite. Current Bingham Canyon production is about 97 kt/d (107,000 stpd) and a similar amount of overburden. Some 70 kt/d (77,000 stpd) of ore are processed through the in-pit crusher and 27 kt/d (30,000 stpd) of ore are transported by rail. The Bingham Canyon mine has yielded more than 11 Mt (12 million st) of refined copper. In 1863, precious metals - silver-bearing lead - were first discovered in Bingham Canyon. What was once a mountain is now a huge open pit. In fact, the mine is the world's largest man made excavation. The pit is some 4 km (2.5 miles) wide and 0.8 km (0.5 miles) deep. Since the pit began operating in 1906, more than 4.5 Gt (5 billion st) of material have been removed. Modernized facilities Electric 21 m3 (27 cu yd) or 23 m3 (30 cu yd) shovels are used to load the haulage trucks. Both 154 t (170 st) and 181 t (200 st) trucks are used to haul the ore to a mobile, in-pit crusher. The crusher replaces three crushers located at the old concentrators. There are two dumping locations at the new crusher, which can handle two trucks a minute. The 1.5 x 2.7 m (60 x 109 in.), 745 kW (1000 hp) Allis-Chalmers gyratory crusher reduces the ore to 254 mm (10 in.) size or less and delivers it to the conveyor. The crusher and conveyor systems are capable of handling 9 kt/h (10,000 stph) of ore.

Jan 11, 1988

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Robert Mermelstein, Robert W. Kilpper

In a long term toxicology study SPF, F-344 rats were exposed 6 hours/day, 5 days/week for up to 24-months to a special test toner at 0, 1 (low), 4 (medium), and 16 (high) mg/m3, or Ti02 at 5 mg/m3, or Si02 at 1 mg/m3 by the inhalation route. The test toner was composed of about 90% random, high molecular weight acrylic copolymer and 10% high purity, medium color, furnace type, carbon black. It was enriched in fine particles such that the respirable aerosol concentrations (ACGIH) were to 0, 0.35, 1.4 and 5.6 mg/m3. There were no effects of exposure on survival, causes of death, body weight, food consumption or clinical chemistry and hematology parameters. There was no evidence for systemic or upper respiratory system toxicity as all of the changes were restricted to the lungs and associated lymph nodes. The lung tumor frequencies in the control (air and Ti02) and toner exposed groups were comparable. There were no changes at the low exposure level, which is the most relevant in regard to potential human exposures. The lung changes at the high exposure level consisted of decreased alveolar clearance, increased toner retention, increased lung weight, chronic inflammation, decreased pulmonary function and a moderate degree of focal fibrosis in all animals. The changes in the middle exposure level were smaller in magnitude than at the high level, and a very slight degree of fibrosis was found in 20% of the animals. In a follow-up investigation, female F-344 rats were exposed to one of three toner concentrations; control, low (10 mg/m3) or high (40 mg/m3) for 13 weeks followed by five, 13 week observation intervals. At the low exposure level, slight clearance retardation and modest inflammatory changes were observed at the end of exposure. They returned to normal values within six months post-exposure. In contrast, at the high exposure level, increased lung weight, decreased alveolar clearance and a disproportionate increase in toner retention, as well as an inflammatory response, were noted, which persisted throughout the post-exposure interval. While no significant histopathological changes were noted at the end of exposure, a very slight degree of fibrosis was observed in all of the animals in the high exposure group, after 65 weeks of observation. All of the above alterations are ascribable to "lung overloading", a generic response to excessive amounts of any dust retained in the lungs for a prolonged time interval. Published accounts in the toxicology literature document that long-term inhalation of large quantities of even innocuous particles such as Ti02, carbon black, petroleum coke, toner, and other polymeric and insoluble materials has resulted in a spectrum of generically similar pulmonary changes. Scaling of the rat-data, using 1 mg dust/g of lung as a threshold for "lung overloading", normal ventilatory parameters and 300-500 day human retention halftimes project "lung overloading" upon long-term exposure to insoluble respirable dust above 0.2-0.33 mg/m3. Other types of information are consistent with an exposure limit in the range of 0.4-1.0 mg/m3 for respirable dust. The absence of definitive toxicology data in support of the current OSHA respirable nuisance dust limit, coupled with the lack of sound epidemiology data, indicate the need to reexamine the validity of the current nuisance dust health standard.

Jan 1, 1991

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By Frederick McNeill, John Harper, Mahmood Khwaja, Shawn Lavoie, Timothy Cloughert, David Polcari

City of Manchester, NH, is implementing a 20-year plan to control and significantly reduce overflow of its sewer system. The long-term control plan had called for large scale box culvert installation through downtown Manchester. The City and the project team evaluated, and eventually selected, tunneling as an alternative to mitigate construction related impacts for open trench approach. This paper provides an overview of the alternative evaluation process; discusses the development of the preliminary design for the 12,000 feet long, 12-ft internal diameter tunnel, including plan and profile selection, subsurface conditions, drop shafts and the anticipated packaging of the separation areas.

Dec 1, 2022

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By Xinming Chen, Huazhe Jiao, Qi Zhang, Yunfei Wang, Liuhua Yang

The effect of initial damage generated by weakly cemented interlayer surfaces on the physico-mechanical properties of layered cemented tailings backfill (LCTB) is considered for the interlayer inclination structure generated by multiple layered backfills in large-scale mining voids. Utilizing the theory of damage mechanics, the damage evolution and constitutive model of LCTB with interlayer inclination is constructed by considering the coupling of interlayer inclination effect and loading. Based on Mitchell’s mechanical model, we analyze the damage mechanism of the inclined cementation surface of LCTB, and derive the expression for the strength of LCTB considering interlayer inclination. The mechanical properties test of LCTB with different inclinations was carried out, and the results showed that the damage model of LCTB established was highly consistent with the experimental curves, which verified the correctness of the model. The initial inclination damage leads to the decrease of adhesive cohesion of cemented surface, and with the increase of inclination, the separation of layered surface, aggravation of misalignment, layered cemented surface is more prone to shear damage, and the mechanical properties of cemented tailings backfill in the lower part of layered surface are not effectively played, which reduces the overall performance of the material.

Nov 23, 2023

By Matthew Burdick, Andrew Rule, Erica Bailey

The Second Narrows Water Supply Tunnel, Burrard Inlet Crossing project for the Greater Vancouver Water District entails deep shaft construction, subway sized pressurized face tunneling through highly variable ground conditions, installation of three permanent steel water mains and construction of elaborate valve chambers adjacent to either shaft. The paper discusses key elements of the planning and implementation of 6.69 m Ø slurry mixshield tunnel boring machine (TBM) assembly in a small diameter deep shaft including incorporation of a fully pressurized launch lock, preparations for saturation diving, surface support infrastructure and initial mining sequence.

Jun 13, 2021

By Onuralp Yücel, Kağan Benzeşik, Ömür Can Odabaş, Selçuk Kan

Extraction and processing constitute an important area in the metallurgy of molybdenum. Molybdenum trioxide (MoO3) production is one of the most important stages in molybdenum production. In this study, the effects of different furnace types on MoO3 production were investigated by using molybdenum concentrate as a raw material obtained during the enrichment of copper ores. Preliminary experiments have been made using a chamber type furnace, and a transition to a pilot-scale has been carried out with rotary kiln experiments. The effects of a different time and atmospheric conditions on MoO3 roasting kinetics were investigated by experimental studies conducted in the temperature range of 500–650°C. It was determined that the optimum temperature and time for sulfur (S) removal was 625°C and 180 min in the studies carried out in the rotary kiln, and it was determined that 0.61%S content was reached with an average removal efficiency of 98%. The activation energy in these sets was calculated as 89.519 kJ/mol.

May 3, 2021

By Dennis E. Peterson

Land subsidence had been observed in recent years throughout the Southwest. Particular examples of this phenomenon that have gained wide publicity axe in the Long Beach and Central Valley areas of California and, the Houston area of Texas. Less well known is the fact that the land surface Is subsiding in many parts of Arizona, including the Phoenix area. The causes of this problem vary from place to place, as do also the rates of subsidence. In Houston it has been related to pumping water from artesian aquifers; in Long Beach to the development of oil fields; and in the Central Valley to both the lowering of artesian pressures in deep aquifers and the wetting of poorly consolidated surficial deposits. The mechanism by which subsidence occurs in southern Arizona, even though it can be correlated with the continued lowering of ground water levels, is not as apparent as in these other cases. It is the purpose of this paper to examine both the causes and affects of land subsidence in southern and central Arizona.

Jan 1, 1965

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

The oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bi, Pb, Sb, As, and Cu contents in the speiss by two-step simulation differed from the industrial data by 0.6 wt.%, 0.8 wt.%, 2.6 wt.%, 7.2 wt.%, and 8.6 wt.%, respectively. Twostep simulation results indicated that the speiss partitioning of Sb, As, and Cu increased from 60.1%, 32.3%, and 27.5%to 81.6%, 67.8%, and 47.2%, respectively, with the smelting temperature increasing from 1050 °C to 1250 °C. While the metal partitioning of Sb and Cu increased from 0% and 2.7% to 15.2% and 13.3%, respectively, with the separation temperature increasing from 400 °C to 700 °C.

Oct 19, 2020

By S. Klein, M. McLeod, S. Gambino, K. Johnson, E. O’Hara

The Mokelumne Aqueducts Resiliency Project (MARP) involves construction of a 16.5-mile tunnel across the Sacramento-San Joaquin Delta (Delta) to replace the existing surface aqueduct pipelines with more resilient conveyance. The tunnel will be bored in Pleistocene-age alluvium at elevations between 100 to 10 feet below mean sea level. At this depth ground conditions are signicantly stiffer and denser than surcial soils and will mitigate potential seismic harards related to liquefaction ground shaking and cooding that could arise from potentially damaged levees. The heterogeneous soil deposits at tunnel depth consist of interbedded layers of stiff to very stiff clay and silt, and dense to very dense clean sand and silty sand.

Jun 23, 2024

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985