Search Documents

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By Steve Rogers

Nautilus Minerals was listed on the Toronto Stock Exchange in May 2006. The company now has major mining companies Anglo America (5.7%), Teck Cominco (7.2%) and Epion Holdings (22.4%) as significant shareholders, and has raised approximately $US346 million dollars to develop the world's first deep-water mine. The company is currently targeting high-grade copper and gold in seafloor massive sulphide mineralization, located near plate boundaries in back-arch basins of the Western Pacific. The first mine scheduled to be developed by the company is located in 1,600 meters of water at Solwara 1, in the relatively quite waters of the Bismarck Sea approximately 50 km from the port of Rabaul, within the Territorial Waters of Papua New Guinea. During 2006 and 2007 the company completed detailed environmental and geological studies, culminating in a number of world firsts, including the world?s first NI 43-101 compliant resource statement and environmental impact study for a seafloor massive sulphide system. Permitting is well advanced for the project, with initial production scheduled for late 2010, subject to timely grant of the permits. Extensive government and stakeholder liaison and engagement has been undertaken throughout the projects life, and is a core feature of Nautilus' desire to "do it right" in all aspects of this new industry.

Jan 1, 2008

By D. L. Misterek, E. J. Slebir, G. W. Ring, M. A. Laird

INTRODUCTION In 1973, the Federal Highway Administration (FHWA) initiated a 10-year program of research on tunneling technology for future highways as a part of a larger Department of Transportation effort on tunnels. The objectives of the FHWA program are to: improve tunnel design technology, reduce costs, minimize adverse environmental impact due to construction, increase the rate of construction, and assure the maintenance of a safe and attractive tunnel environment. The program is divided into four research tasks designed to solve tunneling problems identified by the engineering and field offices of the FHWA. These tasks are as follows: 1. Cut-and-Cover Tunneling 2. Site Investigations 3. Ground Movements - Prediction and Control 4. Highway Environmental Criteria for Tunnels In order to provide input into Tasks 2 and 3, the FHWA is sponsoring an investigation and testing program by the U.S. Bureau of Reclamation to instrument and monitor two sites in the second bore of the Eisenhower Memorial Tunnel located on Interstate Highway 70 at Loveland Pass approximately 97 km (60 miles) west of Denver, Colorado. The tunnel will be approximately 14.0 m (46 ft) in diameter when excavated. The study is designed to generate data on: (1) changes in the state of stress, and movements during and after tunneling, (2) tunnel lining design requirements, (3) developing a

Jan 1, 1976

Energy Developments Ltd. (EDL) has developed power plants at two Australian coal mines that featuring 94 gas-fueled Caterpillar G3516 engine/generator sets. They will convert to electricity 145 kt/a (160,000 stpy) of coal-seam methane gas for sale to a local utility. The $100-million project will cut the sites' methane emissions in half, provide a low-cost energy source and offset mine operating costs. The project began in May 1995. It is located at the Appin and Tower longwall underground mines, 80 km (50 miles) south of Sydney in New South Wales. The installation is one of the first to capture coal-seam gas from mine ventilation air and gas drainage systems. Coal- seam gas contains 40% to 60% methane, which fluctuates constantly. The system is expected to convert 578,000 m3/d (20.4 million cu ft/d) of coal-seam gas to 94 MW. It will also reduce greenhouse gas emissions by 3.5 Mt/a (3.8 million stpy) of CO, equivalent emissions. The Appin and Tower mines each produce 2 Mtla (2.2 million stpy) of clean coking coal. They operate around the clock with about 400 workers per site. The mines are owned by BHP Steel, Collieries Division, which will share the revenues from energy sales. The Appin Power Partnership consists of EDL and Lend Lease Development Corp.

Jan 1, 1997

By G. Sanders

The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominant-lithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below.

Jan 1, 1993

By Yuuichi Umeki, Yuusaku Tominaga

In order to keep good air condition in any specific branch such as coal face and/or heading in an underground coal mine, effective factors of all the branches with respect to the specified branch have been investigated, using computer simulation. Main results of the paper are as follows; 1) A branch in a network is classified to one of three classes of effectiveness to increase, to decrease and not to change airflow rate in the specific branch by altering aerodynamic resistance in the branch. 2) Distribution of position of branches, belonging to each class, related to a specific branch is one of the macroscopic characteristic of a network which is the inherent property of every network. 3) A relation of the aerodynamic resistances of any two branches to keep a constant airflow rate in the specified branch is shown as a monotonous curve. 4) Ventilation transition diagram with the rate of airflow in the two branches as coordinates, and for different rates of airflow in the specific branch as the parameter, is found to be straight lines. 5) Existing range of airflow rates In the specified branch is given as a parameter in the enclosed area in the ventilation transition diagram. Moreover, an expert system to assist ventilation control using a transition diagram of airflow rate is introduced in this paper.

Jan 1, 1991

By John A. DesLauriers, Hans J. Broennimann

INTRODUCTION The early record of tunnel excavating machines in hard rock tunneling has not been one to particularly brag about. We have all heard the stories of major difficulties when trying to break hard rock with machines at promised advance rates of several times that of conventional drill and blast. Unfortunately, sometimes this has not happened. It has been through this trial of the past generations disappointments that today's TBM's have evolved to their present high level of performance in a wide range of ground conditions. Today's machines offer much increased reliability and durability. This translates into high availability to the tunnel contractor. Although there still are occasional disappointments being reported, the state of the art is that reliable and predictable machine excavation of rock now is both a reality and well founded expectation. The most recent editions of Atlas Copco's MINI/MIDI Fullfacer, we feel, make a strong contribution to the reliable performance of todays TBM's---especially in small-size rock tunnels. This report will, 1.) explain the equipment and effect of rock both on the cutting technique and machine performance; 2.) list advantages of the non-circular shape, during and after construction; 3.) list applications in civil and mining industries; 4.) discuss North American experiences, performance and costs; 5.) list advantages over drill and blast and; 6.) discuss briefly lease arrangements.

Jan 1, 1979

By Harry M. Edenborn, Richard W. Hammack

Experiments were done to determine if a mushroom compost-based sulfate reduction system could be used to treat nickel-contaminated mine waters. Sulfate reduction systems were established in columns containing acid-washed mushroom compost. Simulated mine waters containing 2000 mg/L sulfate and 50 to 1000 mg/L nickel were adjusted to pH 4.5 and pumped through the columns at flow rates between 15 and 25 mL/hr. During the first nine days of operation, virtually all influent nickel was removed in the columns by sorption and ion exchange mechanisms. The nickel removal rate then dropped to 18 to 30 mg Ni/day (7.8 to 12.8 nmol/ g-substrate/day), probably due to low sulfate reduction rates. When sodium lactate was added to the inflow, a sustained and seven-fold increase in the nickel removal rate was observed. Bacterial sulfate reduction rates measured in mushroom compost-based wetlands exposed to coal mine drainage are 2 to 20 times faster than the rates observed in this study. Low sulfate reduction rates in the columns may have been due to the inhibition of microbial activity by high nickel concentrations and the removal of labile organic compounds from the mushroom compost substrate during acid-washing. Results of this study indicate that bacterial sulfate reduction can effectively treat nickel concentrations up to 500 mg/L if labile carbon is nonlimiting.

Jan 1, 1992

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By Walter Hoecker

The dissolution of gold in cyanide_ leaching has been we11 published with the genera1 acceptance that gold is oxidised by oxygen and stabilized by complexation with cyanide [1]. The dissolution of gold is essentially an electrochemical process. The rate of the anodic gold dissolution is controlled by the cyanide concentration. - (2) While the cathode reduction of oxygen is controlled by dissolved oxygen concentration - (3) There are a number of factors influencing the concentration of oxygen, and if 1owered substanth.lly will effect the efficiency of the leaching plant. These include: "' salinity "' temperature "'partial pressure "'oxygen consumption rate The use of pure oxygen for· cyanidation is only beneficial if oxygen is rate limiting, Conversely a slurry saturated with air (typically 5 - 8 ppm) may not be enough for maximum leach rate. The diagram below shows the maximum dissolved oxygen levels obtainable with pure oxygen and air. DISSOLVED OXYGEN (MAXIMUM) IN WATER At steady state, the rate of the cathodic reaction must equal the rate of the anodic reaction. Thus the rate of gold dissolution is dependent on both the· cyanide and oxygen concentrations. - (4) Using an average of Do/Den =· 1.5 [2] (where Do and Den are the oxygen and cyanide diffusion coefficients) the table below illustrates the maximum effective oxygen concentrations for given cyanide levels in clean water [3].

Jan 1, 1992

By Barry A. Hillman

The rapid evolution of computer and field sensor technology is now providing the ability to integrate mine and office opera­tions. Digital maps and mine plans as well as CAD and GIS can be transferred to ruggcdized field computers for development of real-time mine surveys and real-time GPS machine navigation and monitoring. Surveyors can insure that their surveys arc accu­rate before returning to the office. Engineers and surveyors are also able to upload field computer-based surveys to mine plan­ning software and directly to mine equipment including shovels, drills, and dozers providing the operator of the equipment with a real-time view of their work space. Production information can be transmitted through dispatch and/or centralized mine servers to update mine plans with mining progress and production data. Static mine models then become a dynamic element of opera­tions, providing greater use of information that emphasizes the spatial aspects of the mine by providing real-time maps, produc­tivity charts, and graphs. This information can be disseminated through various mine communication systems to provide opera­tors and management with real-time feedback as well as daily and weekly reports. Integrated systems now being used in exten­sive trials arc reporting productivity increases of 4 - 7% or more thereby providing rapid payback to the mine.

Jan 1, 1998

By S. Healey, P. Jean, G. Deschenes, M. Fulton

Three years ago, the New Britannia Mine started a project to improve productivity of its cyanidation plant. Results indicated that gold dissolution was strongly influenced by sulphide minerals and that the slower gold dissolution rate had a detrimental effect on overall gold recovery. The leaching strategy had to be modified to address this issue. Changes to the leaching circuit proved to be very successful. The first action was to introduce lead nitrate in the leaching circuit. The strategy of addition of lead nitrate was upgraded in three steps. An on-line free cyanide analyser was installed and the strategy of cyanide addition automated. The enhancement of the leaching kinetics have resulted: an 4% increase of gold recovery, from 87.8% in 1996 to 91.9% in 1999, which represents a reduction of 0.17 git Au in the leach residue; an average of 1330 additional extracted gold ounces per year from 1997 to 1999; a 21 % reduction in the cyanide consumption; the shut down of the cyanide destruction plant; and finally a contribution to the 27% reduction in the overall production cost per tonne of ore.($ 3 per ton). The significant increase of the throughput was instrumental in the reduction of the processing cost. In 1999, the improvement of gold recovery represented an additional gross revenue of $c""l.9 Million. The project is discussed in details in this paper.

Jan 1, 2000

By A. J. Getz

Major precious metals projects are underway in Australia, Papua New Guinea, Indonesia, the Philippines and New Zealand. This article reviews the status of those projects. Included in this review are project location, reserves, method of resource exploitation, anticipated production, and other unique conditions. The article is limited to major precious metals projects in the Western Pacific region. This is not meant to negate the attractiveness or importance of the many other projects in that area. The geographical setting of these five countries are shown in [Fig. 1]. The gold output of the countries has increased dramatically during the 1980s. [Table 1] compares 1980 and 1988 production figures. The compound growth rate is 120%. That reflects the attractiveness of the region’s resource base as well as the impact of price increases, new exploration models and processing technologies, and changes in government policies. If the 10 projects discussed here are all brought onstream, their combined output - at about 130 t (4.17 million oz) - would amount to an increase of greater than 50% over 1988 production from this region. Table 2 shows indicative production levels for each of the 10 projects. Dollar amounts are in US currency unless otherwise specified. Australian dollars have been converted to US dollars at the rate of 1.28: 1.00.

Jan 1, 1990

By Robert S. Mayo

The haulage of muck from mines was first illustrated by Georg Agricola in De Re Metallica in the year 1556. In many of his ancient wood cuts he showed a crude car running on wooden rails. These wheels had no flanges. There were four pins sticking down from the car to guide it along the rails. Eventually they made the wheels of cast iron with flanges on them. In England, coal was hauled from the pit mouth to the nearest river or canal in "wains", or wagons, running on the common highways. These wains carried one chaldron of coal, weighing 2500 lbs and it took six horses to haul these wains over the atrocious roads of that day. Somebody, about 1760, invented a cast iron rail. These were cast iron troughs, 4 ft long laid on wooden sleepers. With these iron rails they found that one horse could do the work of six. But this U-shaped groove trapped all the dirt and grit. Somebody had the brilliant idea of attaching a flange to the inside of the wheel and from then on the rails were of timber protected against wear by a strap of iron. Rolled rails, of wrought iron, were first used in England in 1820. I am sure that many of you people have wondered why the British and American railroads standardized

Jan 1, 1974

By Weston Bourret

The need for wartime supplies of uranium for the Manhattan Project prompted a 1944 study of uranium in South Africa. Uraninite had been reported by R.A. Cooper in 1923 in a Witwatersrand heavy- mineral concentrate, and the search for uranium, therefore, included the district's 30 operating mills. The method of investigation was simple: take bulk concentrate samples from the Wifley tables and determine their mineralogy. Samples were taken on a daily basis, although weekly composites also were taken of some mills. In 1944, most mills had simple gravity circuits and produced (I) a gravity concentrate, and (2) an all-slime [-75 pm (-200 mesh)] product. The tonnage throughput was known, and from that, head assays could be calculated. Concentrate samples were sent to the United States for chemical analyses. A Geiger counter set up in a Johannesburg hotel room provided preliminary data. The early data showed uraninite to be widespread. Microscopic, mineragraphic, and siezing tests were all under- taken in Johannesburg. Ultimately, tests led to a high grade (+90%) uraninite concentrate. Platinum and other heavies were the impurities. In seven months, the investigations had reached the stage where it was possible to forecast an annual production of 5.4 to 7.3 kt (6,000 to 8,000 st) of U3O8. The estimate is still realistic. Additional details are found in Bourret (1981).

Jan 1, 1991

By A. Iordanidis

Ieropigi Fe-Ni deposit is located in northern Greece, in Kastoria?s prefecture near Albania?s borders. A laterite profile exposed by opencast mining and placed near the basement of the mine was chosen for sampling. Ten samples, representing ?pure? Fe-Ni ore, ophiolite-bedrock, ?red? ophiolite and ?enriched? ophiolite were collected, based on macroscopic observation. The samples were analysed by X-Ray powder Diffraction (XRD) for the determination of the mineral phases. Iron and Nickel concentrations of the same samples were also determined by X-Ray Fluorescence (XRF) methodology. The Fe-Ni ore samples consists predomi-nantly of hematite, goethite, chrysotile (serpentine), saponite and quartz. ?Red? ophiolite samples consists mainly of chrysotile, hematite, quartz, calcite and small amounts of paragonite and goethite. Bedrock and ?enriched ophiolite samples are comprised of chrysotile, hematite, calcite, quartz, nontronite, paragonite and sepiolite. The Fe content ranges between 13% and 49% in Fe-Ni ore samples and between 7% and 10% in ophiolite samples. The Ni content ranges between 1% and 3% in Fe-Ni ore samples and between 0.3% and 4.5% in ophiolite samples (the higher content is observed in the so-called ?enriched? ophiolite). A correlation between Fe-Ni concentrations and mineral assemblages is being attempted in order to evaluate the nickel-rich mineral phases. It is shown that the nickeliferous minerals are serpentine, hematite, goethite and saponite.

Jan 1, 2006

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993

By S. N. Groudev

Acid mine drainage waters generated in the uranium deposit Curilo, Bulgaria, were treated by means of a pilot-scale passive system consisting of an alkalizing limestone drain, a permeable multibarrier for microbial dissimilatory sulphate reduction, biosorption and chemical neutralization, and a natural wetland, connected in a series. The waters had pH in the range of about 2.5 ? 4.1 and contained radionuclides (uranium, radium), heavy metals (copper, zinc, cadmium, lead, nickel, cobalt, iron, manganese), arsenic and sulphates in concentrations usually much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The water flow rate through the passive system varied in the range of about 5 ? 15 m3/24 h, reflecting water residence times of about 60 to 20 hours. An efficient removal of pollutants was achieved by this system during the different climatic seasons, even during the cold winter days at external air and water temperatures close to 0°C. The removal was connected with different mechanisms but the microbial sulphate reduction played the main role during the warmer months of the year. However, during the cold winter days the removal of pollutants was due mainly to their sorption by the solid dead plant biomass (cow manure, plant compost, straw) present in the multibarrier as well as to their precipitation as a result of chemical neutralization caused by crushed limestone.

Jan 1, 2006

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987