Search Documents

By P. Roghanchi

The Rock Mass Rating (RMR) system is an internationally recognized classification system that can be used for preliminary ground control design. The RMR system assigns quantifiable values to predefined classified parameters of a rock mass. Assigning a single value rather than a range to each parameter is a source of uncertainty, however, assigning a single value can be useful for further studies related to RMR ratings. Fuzzy systems are being used in an increasing number of application areas where linguistic rules are used to describe the system. In past decades, fuzzy systems have been successfully used in geotechnical and mining engineering problems to cope with uncertain data as well as with vagueness. In such scenarios, linguistic rules and rating-based classification of rock masses have always been questionable. The objective of this study is to apply fuzzy set theory to the RMR classification system. The fuzzy system proposed in this study is specified for weak and very weak rock masses (RMR<50) based on data collected from Nevada gold mines where 68% of RMR data is in the ?poor? and ?very poor? classes. In this approach, a Mamdani fuzzy algorithm has been constructed to evaluate basic RMR89 rating for the ?wet condition.? Comparison between basic RMR89 and fuzzy RMR shows the fuzzy RMR system is valid to predict RMR from the discrete rating of each input parameter.

Feb 27, 2013

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp&apos;s Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011

By G. V. Krishnan, L. Adler

A rock classification for drilling and boring is presented covering most equipment types and providing an estimation of the key parameters for operation, such as thrust and speed, and of performance such as penetration rate and bit life. Drilling and boring are significant and integral aspects of both the mining and heavy construction industries. Together these constitute over 20% of the G.N.P. Drilling and boring represent the most arduous mechanical processes performed in industry. Their misapplication quickly leads to equipment destruction, hazards, and to major delays. The classification is unified in two ways: 1) for a particular rock class several parameters can be estimated, 2) the classification integrates most excavating activities (i.e. digging, ripping and even blasting), and is derived from ground control. The rock classification provides a job property, based on fundamental and index properties, which yields quick and rough estimates of vital information. However it does not obviate the need for a more thorough analysis, and maintaining field records. BACKGROUND In order to adequately describe a drilling operation the conditions, activity, and equipment must be characterized. Of these the major independent variables are the conditions. Conditions focus on the geologic mass and also consider whether the site is surface or underground. The primary component of the geologic mass is the rock type, detailed below in Rock Characteristics. The other components

Jan 1, 1983

By K. G. Correia

The replacement of the dry mining method at Guajú Mine by the dredging method was a means of ensuring its feasibility by maintaining the production levels. Dry mining increased the cost of the deposit with the distance and presented a limited mined volume, while the decreasing grade of the deposit led to a production drop. With the new methodology, there was a considerable reduction in unit cost of the mine and an increase in the production level of a deposit with low heavy minerals content.

Jan 1, 2005

By T. R. Ellis

The vast majority of valuations produced for mineral properties using the net present value method provide an estimate of Investment Value or Use Value. Such an estimate can be a long way from the price that the property would sell at if placed on the market. Indicators from the market need to be used to validate or modify the net present value calculation. The comparable sales and replacement cost approaches used in the appraisal of urban buildings generally fail us in the appraisal of mineral properties. Other methods of sales analysis are introduced. Guidelines for what a minerals appraisal report should contain are presented.

Jan 1, 2000

By C. F. de Mendonca, T. Kater, R. P. de Souza

The authors are to be commended for finding a material for pellets binding that we were unable to uncover during the investigations that led to US Patent No. 3,748,116, “Method for producing metallic iron powder from iron ore concentrate, ” July 24, 1973, by G.G. Reed, Jr., J.M. Karpinski, and S.V. Fox. This patent concerns a method of processing “super’ ‘-concentrates prepared from magnetite or “blue dust” into molding-grade metallic iron powder for use as a bulk commodity, in contrast to current methods which produce small batches that are custom-blended with additives and/or alloye to customer specifications. The one thing we had not found at that time was an organic binder (mineral-matter-free ) that would allow induration to produce hardened pellets that would survive SL/RN Direct Reduction. Peridur appears to provide this missing link needed for large scale (200 t/a, or 220,460 stpy) single line plant capacity consistent with a low market price to ensure greatly broadened use of metallic iron powder. I hope that industry will adopt this combination so that metallic iron powder usage can fulfill its potential

Jan 9, 1985

Caterpillar said it will produce a Cat line of ac electric drive mining trucks. The world’s largest manufacturer of mining and construction equipment said the addition of an AC electric drive truck line will provide its customers with products to fit key applications. “We are very proud of the strong leadership position that Caterpillar has attained with its mechanical drive trucks, and we will continue to invest in strengthening that position,” said Chris Curfman, president of Caterpillar’s Global Mining Division and Caterpillar Inc. vice president. “We also recognize that there are unique applications that would make the addition of ac electric drive an important and attractive complement to our current truck line.” This is the largest investment Caterpillar has made in mining trucks in its history.

Jan 1, 2006

By Robert R. Beebe

At first glance, mineral processing on an industrial scale might seem entirely in the realm of macro-engineering, with large machines operating on minerals and rocks to achieve size reduction, classification, chemical treatment, separation and dewatering. These operations must be conducted on a large scale to be of practical interest. But the machines and processes may not be designed and operated to take fullest advantage of micro-engineering factors. At the same time, idealized designs based solely on micro-engineering research may require adjustments to gain the desired results in the larger scale, operational context. Using micro-engineering research in this way allows the design and implementation of more efficient versions of the machines and processes currently used, while aiding the revolutionary developments unlikely to come from macro-engineered, trial-and-error solutions. Thus, from an industrial viewpoint, micro- and macro-engineering are complementary functions.

Jan 1, 1992

By K. S. Gritton

The implementation of advance control systems brings with it the expectation of improvements in process performance and controllability. Specifically, expectations include a shift in the mean value of the gross measure of process performance, and/or a decrease in process variability. When determining statistically-defensible measures of these benefits care must be taken to preclude process parameters from biasing the determination. Specifically, the effects of ore type, shift personnel, water availability, etc., must all be separated from the effect on performance of the advanced control system. Methods are presented for separating the effects of process control from other process parameters. Examples of the required data analyses are also presented.

Jan 1, 2001

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By Jan L. Reichelderfer, Thomas L. Richardson

Completion of the H-3 Highway Tunnel Project was a critical element in opening this award winning project. The exploratory tunnel was completed as a maintenance tunnel and included difficult shafts extending into the main tunnel cross passages. The project also involved a major addition to the traffic operations center including a deep excavation in close proximity to the tunnel portal structures. The projects also included various completions and improvements to the main tunnels, such as paving, drainage, maintenance, and a variety of critical life-safety issues, such as radio systems, telephones, etc. The highway opened in December 1997.

Jan 1, 2001

By S. G. Hardcastle, C. K. Kocsis

Ventilation is an expensive prerequisite for underground mining. Current mining trends, including increasing depth and mechanization and more stringent health regulations would generally dictate that more air volume is required in order to provide good working conditions underground. However, any increase in the mine’s intake airflow can produce a disproportionate increase in power consumption and hence operating costs due to the cubic relationship between the sup-plied air power and the airflow (Power a Flow3). Furthermore, forecasts of significant increase in energy prices and new commitments with regard to reductions of greenhouse gas(GHG) emissions, determined the mining industry to look into developing new concepts, design tools and incorporate the latest mining technologies in order to lower capital and operating costs while meeting commitments regarding GHG emissions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. A developing trend is to design and plan the mine by means of orebody modelling software, followed by using discrete-event simulation techniques to predict production rates and evaluate various operating scenarios throughout the life of the mine. The authors are currently evaluating how such process simulators could be adapted in order to forecast the need for materials or a specific resource, and one of these would be the mine’s “life-cycle” airflow demand as a function of scheduled production rates and mine operating characteristics. Further to this, based upon the mine’s life-cycle airflow demand schedule, the ventilation system could then be designed using a mine ventilation simulator. This new design approach would integrate in parallel the development of the ventilation system with the current mining conditions, therefore, heading towards “develop-as-you-go” as opposed to developing the system for final requirements with high upfront costs. This new ventilation system design criteria would also incorporate the use of the “ventilation-on-demand” technology, which will further lower development and production costs and implicitly, the mines’ GHG emissions.

Jan 1, 2004

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By J. B. Hedrick

In 2004, rare earths were not mined in the United States. The major supplier, Molycorp, continued to maintain a large stockpile of rare-earth concentrates and compounds. Major uses for these commodities were in automotive catalytic converters, petroleum fluid-cracking catalysts, permanent magnets, glass-polishing compounds, ceramics, metal-alloying additives, phosphors and rechargeable batteries. Consumption of refined rare-earth products decreased. The United States was a major importer and exporter of rare earths in 2004. Yttrium was not mined or refined in the United States in 2004. Imports from China, France and Japan accounted for most of the U.S. supply of yttrium compounds for refined yttrium products.

Jan 1, 2005

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006