Search Documents

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States,2 and in addition, feldspar is produced as a by-product by firms whose major products are spodumene and mica.3 Feldspar is concentrated by hand-cobbing and flotation; the latter forms the major method of separating and concentrating feldspar. Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan and the USSR. According to the U. S. Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 tons and 2,514,000 tons respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel,-tile and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, North Carolina have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water

Jan 1, 1976

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By James R. Runkle

Studies in eastern Ohio, northern West Virginia, and southwestern Pennsylvania determined whether subsidence caused by longwall mining influences soil moisture and tree growth. Soil moisture was measured both over new longwall panels and over an unmined control area throughout the growing seasons of 1990, a wet year when the panels were excavated, and 1991, a dry year. No significant effects of mining could be detected. Tree growth was studied in two pairs of woodlots. In each pair, one woodlot was located over a longwall panel excavated about 1980 and the other over an unmined area. Differences in tree growth between mined and unmined areas were neither significant (for most species) nor consistent in direction. The above results imply that if mining does have impacts they are likely to be highly site-specific and localized such as by disruptions of springs or soil slippage.

Jan 1, 1986

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By M. Hodgson

The redox reactions that occur on pyrrhotite and pentlandite in contact with oxygenated deionized water were examined using voltammetry. Reactions were put forward in which both minerals were progressively hydroxylated to form thermodynamically metastable surface intermediate products. These intermediates were modelled as metal deficient sulphides where a sulphurous layer was coordinated onto the remaining metal sites via polysulphides. Prior to hydroxylation pentlandite exhibited changes in the surface stoichiometry which were not related to pH effects. The formation of polysuiphide-sulphur intermediates were believed to promote collectorless; flotability for the two minerals. Microflotation tests (0.3 g samples) verified that the surface potential and particle size affected the flotation response, excessive oxidation inhibiting the minerals' flotability. Larger scale tests using ore samples (30 g) confirmed that the extent of pulp oxidation, particle size distribution and the presence of frothers affected the flotation response, the findings being in accordance with the postulated model for the hydrophobic species generated on the pentlandite and pyrrhotite surfaces.

Jan 1, 1985

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970

By J. D. Miller

On the basis of nonequilibrium zeta potential measurements by laser-Doppler electrophoresis, the sign of the surface charge of alkali halides in their saturated brines has been established. The results are generally as expected from simplified lattice ion hydration theory. This recent electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble-salt flotation systems suggests that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation results confirm this surface-charge/collector-colloid adsorption model and are presented herein.

Jan 1, 1992

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By A. G. Royle

Although these exhibit similar structures overall, there are more acute valuation problems in alluvials. Most of this description will therefore be about alluvials with comments on bedded vis-a- vis alluvial deposits where necessary. Although geological comments refer mainly to lateritic deposits the method of valuation described applies to all bedded deposits, e. g. coal, limestone, phosphate. In general, the more a deposit suffers alteration during or after its formation and the more the sampling process disturbs its material, the greater the difficulties of valuation. Emphasis is laid on structure, as in any kind of deposit valuation cannot proceed until its structures are understood. Not all the structures found in alluvials will occur in bedded deposits, of course.

Jan 1, 1982

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003

By Eddie Woods, Jon Hurt, Roger May, Paul Watson

The Channel Tunnel Rail Link (CTRL) will be Britain’s first major new railway for over a century—a high-speed line running for 109km (68 miles) between St. Pancras station in London and the Channel Tunnel. The new line has been under construction since October 1998 and the first phase will open in October 2003. The project includes22km of twin 7.15m ID TBM bored tunnels under London and the River Thames, and the 3km North Downs Tunnel, the first major NATM tunnel to be constructed in the United Kingdom since the collapse of the Heathrow Express Tunnels in 1994. This paper will discuss the design of these tunnels and describe the construction progress to date. The discussion will include details of segmental lining design, TBM specification, and sprayed concrete lining design.

Jan 1, 2003

By G. R. Goldak

All of Canada's older uranium mining areas have been intensively prospected and known outcrops have been repeatedly examined. The only ground in these areas which has not been explored is that which is covered by water or other overburden. The discovery of new mines in these areas will, in the author's opinion, depend on the development of new geophysical or geochemical tools capable of locating uranium deposits which are-buried beneath tens to hundred of feet of overburden. Such tools would be extremely useful in Saskatchewan's Cluff Lake and Wollaston Lake areas. Uranium has recently been discovered in significant quantities in these regions but exploration is made extremely difficult and expensive by an almost uniform overburden cover. The author's experience has been confined to Canada but apparently a subsurface uranium prospecting method could be widely exployed in the western United States and Australia as well. Radon-222 measurements have been used for more than a decade on practically a worldwide basis in an attempt to obtain a useful method for subsurface uranium prospecting. It is well known that ha-222 produced by buried uranium deposits can diffuse through an overburden cover so that it can sometimes be detected at surface. An advantage of this method of prospecting is that Rn-222 can be detected with a simple scintillation, ionization or semiconductor detector. One of the essential weaknesses of the method is that the mean diffusion path length of Rn-222 is limited by its very short (3.8 days) half life. For a deeply buried deposit, vitually all of the Rn-222 atoms will decay before reaching surface and, therefore, such deposits cannot be expected to produce a detectable radon anomaly. Thus, except in unusual cases where groundwater or ground air flow assists the movement of radon towards surface, the depth of exploration is probably limited to ten or twenty feet of overburden cover. The high solubility of Rn-222 in water is also a source of difficulty. In an area where overburden covers bedrock with water saturation of the lower overburden levels, the radon will simply dissolve in the groundwater, and soil gas readings at surface will indicate falsely low

Jan 1, 1974

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993