Search Documents

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By James R. Arnold, John O. Marsden

Introduction Metallurgical accounting practices have been revolutionized over the past 15 years by the introduction of low cost personal computers and easy- to-use spreadsheet software. The Chimney Creek metallurgical accounting system takes full advantage of these advances. Data is provided by a PLC-based process control system, IBM data logging, operator logsheets and assay results from an automatatic plant sampling system. The data is organized and stored in an IBM PS/2 system using Lotus 123 and customized accounting programs to provide a comprehensive information management system. Metallurgical accounting for gold plants should ideally provide information for the following: a) Gold production accounting b) Day-to-day process control and operation c) Metallurgical evaluation and process optimization The Chimney Creek system provides all of these while overcoming specific accounting problems presented by SAG milling a coarse feed, grinding in cyanide and dump leaching run-of-mine material. Process description Gold Fields' Chimney Creek mine is located 47 miles northeast of Winnemucca, Nevada, at the northern end of the Osgood Mountains. Ore is processed by a combination of dump leaching and milling processes. The dump leach operation treats approximately 2.0 million tons per year of low grade ore (0.030 oz/ton). Run-of-mine ore is top dumped in 40 foot high pads. The use of three solution ponds for leaching enables an intermediate solution to be recirculated to the leach pad to reduce the pregnant solution flowrate and increase gold tenor of solution to the carbon-in-column (CIC) recovery circuit. Gold recovery is approximately 65% by this method. The milling process employs a SAG mill-ball mill grinding circuit to treat 900,000 tons per year at an average grade of 0.19 oz/ton. The ore is crushed to minus 12" in a jaw crusher prior to feeding the SAG mill. Cyanide is added to the grinding circuit to start gold dissolution as early as possible. After grinding, leaching of the ore is continued in a unique two-stage counter current decantation circuit 1 with 12 hours of leaching between stages . 85% of the soluble gold is recovered from the first stage thickener overflow in carbon columns (CIC). The second stage underflow is treated in a scavenger carbon-in-pulp (CIP) plant. Ultimate gold recovery is over 95%. Loaded carbon from both the dump leaching and milling processes is pressure stripped by hot cyanide solution and gold is recovered from the resulting solution by zinc precipitation. The precipitate is retorted for mercury removal and smelted into bullion. The plant flowsheet appears in Figure 1. Data collection Data for daily metallurgical accounting is obtained from three sources: a) Plant sampling b) Process control system c) Operator logsheets All of the data collection for metallurgical accounting is based around the 12-hour shift operating schedule. Sampling All critical sampling for gold production accounting is performed by automatic samplers (Figure 2). Heath & Sherwood two-stage sampling systems are used for sampling all slurry streams (cyclone overflow, CIP feed and CIP tails). The automatic sampler consists of a pneumatically operated primary sample cutter and a continuous rotary secondary splitter. The cyclone overflow and CIP tails are the most critical samples since these are used to calculate gold into and out of the plant on a shiftly basis. The CIP feed sample gives additional information concerning intermediate dissolution and recovery

Jan 1, 1990

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By Rees D. Groves

Cement copper is ordinarily converted to marketable metal by processing in a conventional smelter and refinery. Because of rapidly increasing cement copper production and limited excess smelting capacity, other techniques were investigated for preparing marketable copper products. One route was to make copper powder for industrial use. The process scheme employed flotation for rejecting the bulk of the impurities, acid leaching to remove residual iron and aluminum, reduction sintering to eliminate oxygen, and grinding to obtain powder. Another route was to sinter the floated and leached copper into the form of anodes and electrolyze these to yield refined copper cathodes. At a current density of 30 amperes per square foot, power consumption for electrorefining was 185 kwhr per ton of copper. The feasibility of preparing commercial-size anodes by sintering is still to be assessed.

Jan 1, 1970

By Craig E. Burson

This paper discusses the relationship between frother types and coal flotation as a function of particle size. It has been found that each frother has a unique size fraction that it will float effectively. This fact is very important when it comes to selecting a reagent scheme that will provide maximum recovery of both coarse and fine particles. Improvements in recovery can be attained when the chemical relationships between frother type and particle size floated are understood. Data from plant evaluations using commercial and developmental frothers are presented to verify the importance of frother types versus size fraction floated.

Jan 1, 1987

By Joseph T. Matoney, Okley B. Bucklen, Claude A. Goode, Philip G. Meikle

INRTODUCTION Annual coal production rose to over 1.03 billion st (931 Mt) in 1990. At the same time the number of mines producing this increased tonnage has decreased over 60% in a 30-year period, from 9230 mines in 1960.1 The great increase in production made possible through continued mechanization requires greatly improved loading facilities just to get coal away from the mine. Also the trend to combine production from more than one mine and cleaning it in a single preparation plant continues. A recent census of US coal preparation plants indicated that 310 plants were in operation.2 In addition to increased loading capacity, storage and blending facilities are more necessary both at the producer and user end. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit-train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit-train movement, operators have found that storage is an economic necessity. In unit-train practice, large predetermined quantities must be loaded in relatively short periods of time, as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To load out promptly and economically. 2. To facilitate blending in order to even out chemical and physical inconsistencies and to prepare desired products or to attain maximum product uniformity. 3. To store certain sizes whose prices and market demand fluctuate with seasons and to permit shipping in good weather. Coal storage, then, is necessary and desirable, both from production and utilization standpoints. There are, however, several undesirable aspects attendant to the storage of coal, the most important of which are oxidation and spontaneous combustion, changes in properties which may affect utilization of the coal, degradation of coal due to rehandling, and the added cost of handling and storage facilities.

Jan 1, 1991

By H. K. Conn

This paper discusses briefly the evaluation of chrysotile asbestos deposits in ultramafic rocks. Such deposits are limited to serpentinized peridotite and/or dunites. The purpose of any evaluation is to determine whether a deposit contains sufficient ore mineral to justify profitable exploitation. Dimensions of a mineral zone are established by conventional methods, such as mapping, ground magnetic surveys, diamond drilling or underground exploration. The value of the contained asbestos fibre Is dependent on numerous physical properties such as fibre length, strength, flexibility, as well as the actual amount of fibre present. The determination of grade is difficult. The Quebec Standard Test (Q.S.T.) is used to grade fibre according to the proportionate lengths of fibre present. A method of visual vein counting allows calculation of an approximate percent fibre together with a simulated Q.S.T. Various drilling methods are discussed, diamond drilling is favored. Bulk sampling is required to determine fibre quality. Correlation of visual techniques and laboratory methods are often difficult. Reasons for any variance are discussed. Underground bulk sampling of most potential ore zones is strongly recommended to confirm the viability of the property. Evaluation of slip fibre deposits requires greater reliance on laboratory testing as visual methods are difficult to apply. Cross fibre has greater inherent strength.

Jan 1, 1971

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By Joseph M. Chelini

The report shows the sensitivity that nine different cash-flow factors have on the discounted rate of return calculated from feasibiliity- studies on potenital open-pit orebodies of silver, copper, and uranium. Cash-flow factors of "grade", "market value", and "recovery" are. the most sensitive. This verifies the need of reliable estimates for these factors. The cost of evaluation of "preproduction cost" is the least sensitive. This gives credence to the fact that more consideration should be given to compiling sufficient data, as the largest financial losses are not in the cost of evaluation but rather in the abandonment of an unprofitable mining operation after a commitment of capital is made on the basis of an incomplete evaluation. Sensitivity analysis of cash-flow factors enhances evaluation programs by disciplining the collection of data and allowing more realistic distribution of evaluation monies.

Jan 1, 1971

By Nath S. Parate

With the extension of mining beneath residential and industrial areas, it is becoming increasingly necessary to extract coal and minerals in such a way that subsidence damage due to groundmovement is reduced to a minimum. Understanding clearly of the mechanism of subsidence development is a must in view of the environmental problems and the energy crisis today. This paper gives a simple analysis of various components resulting from subsidence and the influence of other factors on their development. An up-to-date review of the subsidence and strain profiles is presented, with particular references to the coal mining operations. The importance of this topic from mining damage to structures, buildings properties and environment in mining areas is undeniable. Field results are discussed.

Jan 1, 1982

By R. K. Mehta

Conventional triboelectrification based dry coal beneficiation methods require ground coal as a prerequisite feed material, energy intensive static-in-line mixer or cyclonic tribocharger configuration, and transport and/or improvement in the design of free-fall separators to improve the separation efficiency of [me pyrite/mineral matter from coal. The proposed paper illustrates the two concepts. First, the use of ceramic media in a polyurethane lined attitor in achieving simultaneous grinding and differential charging. Second, the use of an electrocentrifuge to selectively separate coal from mineral matter present in the triboelectrified mixture. It is of interest to note that some ceramic media can satisfy the requirements of both desired density and work function to achieve grinding and differential charging.

Jan 1, 1996

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By D. W. Park

A vast majority of longwall operations in the United States use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite element model of the shield structure was made to study responses of each long wall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested to develop a technique incorporating the finite-element method to evaluate the real-time shield performance for the purpose of effective ground control.

Jan 1, 1992

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By Herschel H. Potter

Back injuries arising from such activities as lifting and handling objects have been and continue to be constant and undiminishing hazards of the occupational environment. Back pain in one form or another is experienced by almost a1 1 individuals. During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, it has not produced any great change in the incidence of the injury. The human spine remains the most vulnerable area of the muscul o-skeleta1 system. Back injuries account for about 400,000, or 18 percent, of all disabling work related injuries each year according to the National Safety Council estimates. These serious back injuries are estimated to have cost more than 1.9 billion dollars in 1976 in medical and lost time pay. 1

Jan 1, 1981

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970