Search Documents

By James A. Commins

Accurate engineering predictions of energy needs for pollution control equipment used in surface mining operations is critically important to sound management selection of control alternatives. This paper will describe a procedure for evaluating two control alternatives with different energy needs. Three steps are involved: an analysis of the pertinent regulations, a determination of the size distribution of the particles being emitted, a calculation of the energy needs and costs of the candidate control systems as a function of these regulations and emission characteristics. The principal air pollutant to be controlled in surface mining operations is particulates, or dust, some of which is already on the material introduced into the primary crusher and other dust which is generated by the various steps in the subsequent processes. The requirement for control stems both from regulations concerning workers at the operating site, and the community surrounding the operations. In order to speak quantitatively about the need for control we will use regulations that pertain in Pennsylvania although it must be borne in mind that such regulations vary according to juristiction.

Jan 1, 1975

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

By Todd Kilduff, Michael Tinney

The North Temple Tunnel pedestrian underpass in Salt Lake City, UT was built using a pipe canopy method that met significant challenges in potentially running ground conditions. Kilduff Underground Engineering (KUE) was the designer for the 20-foot-diameter SEM tunnel, Design-Build contract. Geotechnical data indicated ground conditions consisted of loose silty gravel for the majority of the face overlying soft to medium stiff clays in the tunnel invert. KUE designed a pipe canopy as pre-support to stabilize cohesionless gravels in the crown, a shotcrete initial liner with lattice girders to minimize disturbance of the finer-grained materials in the invert and a final liner with waterproofing system. The project was presented with a few unique challenges, primarily from the adverse ground conditions, but was successfully completed safely and schedule

Dec 1, 2022

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1. Dump leaching, where the ore is moved from its original location to be leached at another site. 2. In situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains.

Jan 1, 1969

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By J. García, B. Arango, F. Calderón, O. J. Restrepo-Baena, A. Carreno, L. Rojas-Mendoza, J. Pérez, E. Bedoya

"Tungsten extraction is a subject of global interest due to is properties. These properties, such as its high melting point, have contributed to the development of metallurgical extraction processes that can be adapted to the particular chemical composition and mineralogy of the ore. In Colombia there is a research deficit in tungsten related areas, and especially with regard to its extractive metallurgy. In this study the physical, chemical and mineralogical characterization of a sample were performed. Subsequently, crushing and grinding were employed to reduce the material to a more convenient size, making it suitable for further concentration and metallurgical processes. Through physical concentration techniques it was obtained a concentrated ranging between 60 -70 % of WO3 content.INTRODUCTION Tungsten is a metal of great economic importance due to its excellent properties such as high density and extraordinary melting point 3422°C), which is indeed the highest of all the elements. Tungsten is primarily used in metal alloys, manufacture of special steels, coatings and catalysts; products of interest to both international and national industry. However; given that the use and economic value is determined by the percentage of tungsten in the mineral, particle size and chemical associations, it becomes essential to properly characterize the mineral to further define possible metallurgical extraction routes. The metallurgical processes for minerals enriched in tungsten may vary depending on location and the genesis of the ore body, which means that for each ore a particular set of operating conditions must be determined. This is important since process standardization can lead to misuse of the mineral resource. However, in Colombia there is a research deficit as it relates to minerals enriched in tungsten and to its extractive metallurgy. Then, there is a need to conduct studies that can lead to a better understanding of the ore, and to develop extraction processes for the metal of interest. EXPERIMENTAL A state of the art review was made in order to gain insights of the tungsten metallurgical process. Comminution was necessary with the aim to reduce the sample size; therefore the sample was taken into crushing and grinding stages. Concentration techniques such as magnetic separation, gravity and / or electrostatic were also applied. Physical, chemical and mineralogical characterization were performed by using polished sections, grain size determination, X-Ray Fluorescence (XRF) and X-ray diffraction (XRD) techniques."

Jan 1, 2015

By Clark D. Harrison

This paper compares the ash slagging potential of Illinois No. 6 Seam coal: as raw coal; as commercially cleaned coal processed in a baum-jig plant; and as coal cleaned to a reduced ash specification at the Electric Power Research Institute's Coal Cleaning Test Facility. The comparison is based on: ? ASTM ash fusibility data ? A slagging index ? Gravity fractionation analyses of critical mineral matter compounds ? Comparative pilot combustion tests. The first three grounds of comparison are laboratory data; and the final comparison involves burning approximately 15 tons of each coal at CONOCO's 1.5 MBtu/hr (440 KW) test combustor. The evidence of these .four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois 90. 6 Seam coal.

Jan 1, 1984

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By T. Hackett

Western underground coal reserves are tremendous, but recovery in western seams can be poor because of mining problems caused by deep cover, geologic anomalies, and thick seams. For instance, many seams contain a rock parting too thick to be extracted economically with the coal. This forces the operator to mine the coal above or below the parting. Subsequently, the rock pressures induced by mining make the part left difficult or impossible to extract by standard mining methods. Because upper and lower parts of the seam are frequently of minable thickness, the presence of rock partings can result in a significant loss of coal. Given a longwall recovery of 60 pct and equal thickness for the two parts of the seam, overall recovery is reduced to less than 30 pct if one part only is mined. The coal left in place is unavailable to meet the nation's energy needs, or to produce revenues for coal companies or government. [ ] Multi-slice longwall mining has the potential to recover the portion of split seams that are now left in the mine. Using superimposed standard longwalls with chain pillars, overall recovery could be doubled, depending on panel and pillar widths. Using a combination of advancing and retreating longwalls in descending slices, overall recovery could be improved to more than 80 pct. Because of the potential for improved recovery, the Bureau of Mines is analyzing the ground control factors affecting multi-slice longwall under western mining conditions and is conducting field trials at a planned multi-slice operation.

Jan 1, 1987

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By Musa I. Marto

The theory of ore flotation has developed at a rather fast rate and the application of theory to practice has been successfully investigated. Significant technological advances have been made in such areas as control of the ore grade, automation in metallurgical control through conductivity measurements, and the development of faster and continuous analytical techniques for ore pulp analysis. Further significant improvements in mill control are being_ investigated through the application of a computer control to the process. This represents the more advanced trend in process control. At the heart of a control system installation, the digital computer will communicate directly with process instrumentation, perform' complex calcu¬lations to determine on a timely basis the control settings for attaining optimum results and automatically furnish signals to effect control actions. The process is considered as an integrated unit and economic criteria are used to measure its performance. The approaches to a mathematical model development to describe the process, optimization and control schemes as applied to an ore beneficiation process will be discussed.

Jan 1, 1962

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By C. W. Schultz

The distribution of material passing a screen, or a set of screens, is described by the equation [ ] where p = the probability that a single particle will pass the screen on a single presentation k = number of layers of screen cloth n = distance from head of screen expressed as number of screen openings. This model can be used to predict the performance of conventional screening operations (i.e., k = 1) as well as the so-called "statistical screening" operations. Using this technique, in which multiple identical layers of screen cloth are employed, screening can be carried out at a finer size than is possible with conventional techniques with no loss of separation efficiency.

Jan 1, 1969

By David M. Parkes

Geology is frequently complicated, hence only more regular deposits are mined. Coal is generally thick, often steeply pitching and usually soft or well-cleated. Due to competition from open-pit mines, only two underground mines are operating, McIntyre and B.C. Coal. Several other mines are being planned, the method being evenly divided between hydraulic, longwall, and room and pillar. McIntyre mines in the flat part of their formation (up to 20 degrees) uses continuous miners and shuttle cars in the 3m and 6m seams. This company is considering a retreating longwall face. B.C. Coal operates a hydraulic mine in a 16m thick seam dipping at 10 to 55 degrees with a productivity of about 20 tonnes per manshift.

Jan 1, 1982

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores&apos; as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By B. Mishra, Q. Shi, Y. Zhao, G. Zhao

Shale is anisotropic due to the presence of bedding planes. The anisotropic strength of shale has been extensively studied. However, little attention has been paid to the size effect on shale strength considering the anisotropy. This research uses the discrete element method to study the size effect on the strength of shale under the uniaxial stress state. It is assumed that the anisotropy is caused by bedding planes, while the size effect is caused by randomly distributed flaws. The numerical model of shale comprises three components: shale matrix modeled by bonded particles (2) bedding planes modeled by smooth joints (3) flaws modeled by discrete fractures. The developed model is scaled to different sizes and tested in the uniaxial compression and the direct tension tests. The test result show that the uniaxial compressive strength decreases as the specimen size increases when the loading direction is perpendicular or parallel to bedding planes. The uniaxial compressive strength is determined by the flaws while the bedding planes only play a limited role. However, the size effect on the direct tensile strength depends on the direction of bedding planes. When the loading is perpendicular to bedding planes, the size effect is not prominent. The direct tensile strength is determined by the bedding planes while the flaws have little effect. When the loading direction is parallel to bedding planes, the direct tensile strength decreases when the specimen size increases. The direct tensile strength is determined by the flaws while the bedding planes have little effect.

Mar 2, 2022