Search Documents

By S. Behl

A major limitation in developing successful selective flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper a correlation between selectivity of flocculant adsorption and separation efficiency is outlined and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1992

By Lester F. Sanford

Located in the Santa Cruz Mountains eight miles north of the City of Santa Cruz and inland from the coast, lies a typical beach sand consisting of quartz and feldspar grains of the Santa Harguerita formation of the middle tertiary age, Reserves of over twenty-five million tons of this sand form the deposit presently being harvested by Pacific Cement & Aggregates, a Division of Lone Star Cement Corporation. The deposit ranges from 350 to 700 feet above sea level and varies from two percent passing a 200 mesh screen to ten percent retained on a ¼ inch screen (see Figure '#l) In 1929 the first sand plant went into operation at this site. It was replaced by a new plant in 1937. This plant continued operation until the middle of 1965 when replaced by the modern plant described in this paper.

Jan 1, 1967

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By Stanley O. Reichert

At nuclear facilities, three types of radioactive waste must be managed: (1) high-level liquid waste containing fission products from the chemical separation of irradiated uranium, (2) low-level condensates from the concentration of the high-level waste, and (3) dry solids such as obsolete process equipment, spent ion exchange resins, and irradiated metal scrap. The geological and environmental characteristics of a site are important considerations in planning the waste management program. At the Savannah River Plant, low-level liquids and dry solids are safely and economically placed in the soil where the geologic and hydrologic conditions are favorable. Within the general area where the waste originates, studies are made to locate seepage basins and burial grounds in the most favorable sites: (1) soils should have a high ion exchange capacity and moderate to low permeability, (2) the water table should be deep, and (3) burial sites should be relatively distant from the nearest flowing stream.

Jan 1, 1968

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By M. S. Enders

The McDonald deposit is a volcanic-hosted epithermal gold resource that is estimated to contain 251,000 kg of gold in 375 Mt of ore at an average grade of 0.7 g/t gold. Phelps Dodge exploration geologists, working for the Seven-Up Pete Joint Venture, discovered the deposit in 1989. By the end of 1992, 494 drill holes for over 113,000 m of drilling, bulk sampling, soil geochemistry, geophysics, metallurgical testing, engineering, and environmental studies had been completed to support feasibility studies. The discovery of McDonald required vision, persistence, and commitment of everyone from the geologist on the drill rig to the senior management of the company.

Jan 1, 1995

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971

By Alan S. Peck

Chemisorbed oleate films on the surfaces of fluorite, barite, and calcite were studied by means of infrared spectrophotometry. Evidence is presented which indicates the mineral anions, i.e., fluoride, sulfate, and carbonate, are displaced from the mineral surfaces as a result of the adsorption from aqueous solutions. Also, chemisorption reactions between oleic acid and fluorite or calcite occurred spontaneously in the absence of water. Carbon dioxide was identified as a reaction product when dry calcite was contacted with oleic acid. There was no evidence of reaction between oleic acid and barite in the absence of water.

Jan 1, 1964

By P. Bartel

Coal cleaning can be effected by the bacterium Sulfolobus acidocaldarius, which in oxidizing sulfur and dissolving mineral matter requires carbon dioxide and oxygen; carbon dioxide as a carbon source and oxygen as an electron acceptor. The desulfurization of coal by thermophilic bacteria under elevated partial pressures of carbon dioxide and oxygen was studied at a total pressure of 1 atm. The partial pressure of carbon dioxide was varied over the range 0.00032 to 0.33 atm (0.00032, 0.007, 0.10, 0.33 atm), and the partial pressure of oxygen was varied over the range 0.14 to 0.40 atm (0.14, 0.21, 0.30, 0.40 atm). The maximum rate of coal desulfurization increased by 32%, from 9.0 to 11.9 mg S/1 hr, as air was enriched in carbon dioxide from its atmospheric level of 0.00032 atm to 0.10 atm. Enrichment with carbon dioxide up to 0.10 atm, at constant oxygen partial pressures, increased the desulfurization rate, but enrichment to 0.33 atm caused the rate to decrease. At constant carbon dioxide partial pressures, the desulfurization rate was maximum at oxygen partial pressures of 0.21 and 0.30 atm. At higher (0.40 atm) and lower (0.14 atm) oxygen partial pressures the rate decreaed by 9 to 20%. The desulfurization rate decreased by 58X, from 9.0 to 3.8 mg S/1 hr, when the air pressure was increased from 1 atm to 3 atm. The effects justify an economic analysis during design and operation of a commercial air feed in a process to desulfurize coal by microbial action.

Jan 1, 1986

By William M. Warren

Recent sinkhole activity in carbonate terranes of Alabama has resulted in damage to transportation lines, structures, utility lines, and property in general. Active sinkhole development and subsidence has been well documented in Alabama, Florida, Pennsylvania, and South Africa. An excellent example of the potential danger resulting from this activity is the spectacular collapse under a South African gold ore crusher plant that resulted in the death of 29 men in 1962. Due to the severity of the problem in certain localized areas in Alabama, a detailed investigation is being undertaken by the Geological Survey of Alabama and the U. S. Geological Survey. One of the most promising techniques is the application of aerial photography and thermal infrared imagery. Conventional and modern remote-sensing techniques are being used in Alabama to locate and define areas of sinkhole activity and to determine which areas are most prone to its occurrence.

Jan 1, 1975

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By Kadri Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. . The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1992

By J. M. King, C. J. Boggs

Acquisitions of mineral properties and companies can saddle the acquirer with unexpected and substantial liabilities and obligations incurred by the acquired or selling company that are not readily apparent from review of the company's books or files. This paper will address selected areas of concern, such as environmental and reclamation liabilities, problems of foreign ownership by the buyer or seller, pension obligations, plant closing laws, effective title review, land use and zoning.

Jan 1, 1992

By B. A. Bancroft

A quality assurance program consists of all those activities aimed at providing confidence to the purchaser that the suppliers quality system will provide a product that will satisfy the purchaser's stated quality requirement. An organizing principle is necessary for prioritizing the quality control activities of quality personnel in the face of a myriad of technical possibilities, data-analytic applications, and an overwhelming number of possible activities promoted in the literature and by quality "gurus". The organizing principle I like is that quality assurance exists when those involved in the quality process: (1) know what they are supposed to do, (2) can tell if they are doing it and are set up to continue doing it and, (3) if they are not, they can remedy the situation in a timely fashion. Any incremental activity which facilitates this organizing principle is a continuous improvement activity. That activity which has the chance to facilitate this principle to the greatest extent is the next one to work on. In these days of lean corporate and regional staffs it is as important to know what not to work on as it is to know what to work on. In this paper I shall discuss in general terms the implications of this organizing principle for the design of Quality Assurance (QA) Programs for coal mines and also provide some comments about the application of Statistical Process Control (SPC) methodologies in the coal industry.

Jan 1, 1994

By H. S. Castro

The by-product molybdenite technology in Chile is reviewed. Flowsheets, reagents and some operation features for the actual six Chilean moly plants(Chuquicamata, El Teniente, El Salvador, Andina, Las Tortolas and Pelambres), are presented. The chemical and physicochemical factors involved in the depression of copper and iron sulfides during the selective flotation of molybdenite, with sodium sulfide, sodium sulfhydrate, anamol-D and LR-744, are discussed. Advances in technology to solve problems of excess of lime (precipitation with sulfuric acid); excess of residual flotation reagents (activated carbon and kerosene); and optimization of depressant consumption (Eh control, nitrogen and low-oxygen air), are discussed.

Jan 1, 1998

By L. Figueroa

Electrochemical methods have potential to treat waters impacted by mining, while simultaneously producing a recoverable metal product to off-set treatment costs. Mining-impacted waters may present challenges with electrochemical treatment due to low concentrations and complex solutions of numerous dissolved metals. This paper presents an evaluation of the potential strengths and limitations of abiotic electrowinning of mining-impacted waters. In particular the impacts of chemical composition on metals removal are evaluated. Results of bench-scale experiments demonstrate the potential to remove metals on the cathode (copper, cadmium, lead), as well as the anode (manganese). Pre-treatment for iron and aluminum may be needed and post-treatment pH adjustment would be necessary. INTRODUCTION Due to continually increasing demand for metals, new technologies and innovative applications of existing technologies are needed to recover metals from mining-impacted waters. Electrochemical methods have long been used for metallurgical processes with solutions containing high concentrations of the target metal. However, electrochemistry also has potential to treat waters with lower metal concentrations, while simultaneously producing a recoverable metal product to offset treatment costs. Electrochemical water treatment may have several benefits over traditional alkaline treatment for acid rock drainage (ARD). Sludge produced from alkaline treatment has high water content that is difficult to dewater, even for treatment plants producing a relatively high-density sludge. For example, the Argo Tunnel Water Treatment Facility (Argo Facility) in Idaho Springs, Colorado uses hydrated lime to produce a high-density sludge with a solids content of 20 to 25 percent and filter cake with solids content from 30 to 35 percent [1]. Furthermore, costs for managing the sludge are significant, approximately $90,000 per year for treating approximately 150 million gallons of water [1]. Although not the case for the Argo Facility, sludge produced from alkaline treatment of ARD has potential to be classified as hazardous. Disposal of sludge also opens up the potential for future liability depending on the sludge’s chemical stability and methods of disposal. In contrast to alkaline treatment, electrochemical treatment produces metals in elemental and other highly-dense forms on the cathode. If metals concentrations and flow rates are sufficiently high, the metals recovered may help offset overall treatment costs. In addition, sludge production would be reduced, if not eliminated altogether, thereby reducing both disposal costs and potential future liabilities as well.

Jan 1, 2019

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015