Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By D. Dunbar

Flooding of open pits now receives considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit lake deep waters can effectively eliminate oxidation of pit-wall sulphides. A state-of-the-art, coupled physical-geochemical pit lake model is used to verify that a cost-effective, environmentally responsible closure strategy for the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia is to adopt a controlled, two-stage infilling of the open pit upon cessation of operations. By filling the pit initially with highly saline waters from evaporation/infiltration basins and naturally saline deep groundwater, followed by capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within 1 to 2 years, followed by the rapid onset of sulphate reducing conditions in the bottom waters. Hydrogen sulphide produced by sulphate reduction will readily react with dissolved metals to form highly insoluble metal sulphides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental management strategies. The proposed plan allows for: 1) safe storage of saline evaporation basin waters; 2) the potential for passive treatment in anoxic bottom waters of ARD seepages from other mine site operations should they arise; and 3) a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2001

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By James Corcoran, Richard McLane, Joseph DeMello, Eric Carlson, Hans van de Vrugt

The Los Angeles County Transportation Authority’s Purple Line Extension Phase 1 is a $3.12 billion (USD) design-build, underground heavy rail project, connecting an existing station at Wilshire Boulevard and Western Avenue and extending west 3.92 miles under Wilshire Boulevard and terminating approximately 550 feet west of Wilshire/La Cienega Station. The project alignment runs through the heart of the world famous La Brea Tar Pits and one of the world’s largest urban oil elds. This paper presents a case history of the planning, design, and construction efforts to achieve successful construction of the bored tunnels through Reach 3 of the alignment. Further, this paper outlines the proactive partnership between the owner, Los Angeles County Metro (Metro), the Design Builder, Skanska-Traylor-Shea oint enture (STS), and Southwest Geophysics who provided the geophysical services. Specically, the project included background review of historic site data (e.g., oil eld maps, building foundation plans, historic aerial photographs, etc.), geophysical demonstration testing to ascertain the capability of borehole magnetics to detect oil wells, directional drilling of thousands of feet of horizontal and vertical boreholes, collection of high resolution magnetic gradiometer data along vertically and horizontally cased boreholes as well as the collection of surface magnetometer data, discovery (“ground truthing”) of detected geophysical anomalies, and abatement of potential obstructions within the tunnel alignment.

Jun 23, 2024

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995

By A. K. Fallaw, D. L. Taylor, G. Wang, L. R. Moore, S. Dobson, C. B. Parkinson

"Over the years, the decline of high grade ores have become an increasing problem in the global mining industry. As such, techniques and chemistries must change in order to continue to meet the market demand and quality. Reverse cationic flotation of quartz and silicates is one of the most important techniques for generating the industry standard product from minerals such as iron and phosphate ores. Amine collectors are the global standard in such processes. However, as the ore quality continues to decline so must the chemistry change to meet the change in ore composition. This paper will focus on the introduction and full scale application of a novel amine collector towards a cleaner flotation process in phosphate beneficiation with Crago process. The results suggests the collector is capable of improving the phosphate recovery, in this cleaner circuit, to approximately 94% with minimal sensitivity to the everyday changes in feed grade.INTRODUCTION The days of mining high grade minerals are long gone, but the demand continues to increase. Phosphate ore, for example, is most dominantly demanded from the agriculture industry as a fertilizer component (i.e. diammonium phosphate, DAP) (FAO, 2014). Some literature suggests that global food production must increase by approximately 70% by 2050 (Cordell, 2009). It is also suggested that the peak global phosphorus production will occur around the year 2033, which is the period at which the easily accessible reserves have been depleted. Currently, phosphorus is commonly mined with a BPL (Bone Phosphate of Lime) concentration of 12-20% and a remainder typically being gangue minerals such as silica, clays, metal oxides, calcareous minerals, and carbonaceous minerals. These gangue components can lead to various negative processing and utilization consequences. Calcium, from carbonaceous minerals, is problematic due to the elevated levels of sulfuric acid required to convert the phosphate rock to the acid form (SRI Consulting, 2009). Calcium can also lead to elevated dosages of flotation reagents due to the desire of the fatty acid to coordinate to calcium minerals. Carbonate leads to increased levels of foam during the wet acid process. Silica is associated with the level of insols (acid insolubles), which must be less than 10% in the final concentrate that will be transferred to the chemical plant for acidification. Phosphate ore can generally be classified as carbonaceous or siliceous (El-Shall, 2003). Siliceous ores are commonly processed through various sizing steps followed by multi-staged flotation (Figure 1) (FIPR, 2014 & Güven, 2010). Though the higher grade phosphate pebble is declining, many mines are still able to size good enough to produce some amount of such pebble. Unlike most metal flotation processes where grinding is a necessity for an optimal process, Florida phosphate flotation does not generally require aggressive grinding and can typically operate at 0.1-1.0 mm. The rougher flotation step applies pH modification to achieve the optimal pH of 8.8-9.3 followed by conditioning with a fatty acid type collector, which builds a hydrophobic waxy layer on the surface of the particle to assist in the flotation. This generally achieves higher than 85% recovery of a product with 50-60% BPL and 15-30% insols. Unfortunately, DAP production generally requires 3.5 tons of phosphate rock containing greater than 63% BPL to produce 1 ton of phosphoric acid (ArgusMedia, 2014). Thus, further purification is required to achieve the grade by the chemical plant for fertilizer production. After the fatty acid is scrubbed off the phosphate particles using sulfuric acid (pH 2.5-3.5), the pH is generally operationally readjusted to 6.5-7.2 by washing with “fresh” water. A second collector is applied prior to the cleaner, which is a reverse cationic flotation process. This collector is typically a cationic amine based reagent, which should have an affinity for silica containing mineral"

Jan 1, 2015

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By R. L. Grayson, S. B. Bealko, L. L. Chasko, D. W. Alexander

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies, including a fire or explosion, a massive roof collapse, mine inundations or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training.

Jan 1, 2010

By Charles C. Dahl, Gordon C. Presley, Andrew E. Nevin, Bruce A. Kennedy

How does SME-AIME cope with profound changes in technology, markets - and most importantly - in employment patterns facing its membership today? This is the question that prompted the Society's Board of Directors to appoint a Long-Range Planning Commission (LRPC) (see ME, Feb. 1984, pp. 118 and 128). This is also the question addressed most particularly by the LRPC's Scope Committee. The Committee started its deliberations by asking such basic questions as "Who are we?" and "What is our business?" The Scope Committee then reviewed the findings and recommendations of other more specialized committees to develop and integrate their concepts of the Society's business for the next 10 years. The policy-making suggestions of the LRPC were reviewed and acted upon by the Board of Directors at its open meeting in Los Angeles on Feb. 26, 1984. At the Oct. 23-26, 1984 SME Fall Meeting in Denver, the Board will again review LRPC recommendations. In answer to the question "Who are we?" the Scope Committee proposed description, which was accepted by vote of the board of directors: . . A technical and professional organization that consists of individual members, namely those mining engineers, metallurgists, geologists, earth scientists, economists, managers, educators, and other professionals concerned with all facets of exploration, production, distribution, and using of mineral commodities. "These mineral commodities include all metals; industrial minerals, including construction materials and fertilizers; coal, oil shales, tar sands, and other mined fuels. Among the earth's mineral resources, only wellpumped oil and gas lie outside the Society's specific purview. "Traditionally, SME members work in the fields of engineering, technology, exploration and discovery, development, construction, mining, quarrying, beneficiation and processing, handling and transport, equipment manufacturing, sales and marketing, data processing, safety, land reclamation, environmental protection, taxation, administration, and management of these elements. "Members practice their professions in industry, in universities and research institutions, and in government. They may be operators, manufacturers, sales persons, contractors, consultants, analysts, researchers, educators, advisors, regulators, or members of supporting staffs. "The members of the Society are leaders in dedication to their crafts, in innovation, and in the pursuit of excellence. Among their numbers they count the most distinguished of engineers, applied scientists, and managers. "The Society is based in the United States, is active on a worldwide basis, and is open to nationals of any country. Certain qualifications must be met for attaining and maintaining membership." Purpose of the Society As to the question "What is our business?" the Scope Committee restated our purpose in light of current practice and the constitution of AIME and the bylaws of AIME and SME. The Board of Directors accepted the following proposed purpose of SME: "To further the professional development and well-being of its members by publishing and distributing technical writings, news, and information; by sponsoring meetings of members; by providing forums for discussions and for continuing education; and by fostering communication on the subjects within its purview. "The Society assists educa-

Jan 4, 1984

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Stanley M. Jarrett

Gentlemen, I am pleased to address this gathering of engineers and operation managers representing a large and important segment of the metal and nonmetallic mining industry. Since you know from the printed program that the theme of my paper is the furthering of safety in open pit mines, perhaps you will have guessed that I will also comment upon the image created in the public mind by the industry's safety record and the potential consequences thereof in national health and safety legislation. Operators of surface mines have some cause to congratulate themselves on the basis of figures issued by the national safety council which show that lost-time accidents per-million-man-hours in surface mining (11.18), is lower than that of all other mining. Moreover, the accident frequency in surface mining is only slightly above the median accident rate for all American industry (8.87). That is a good record.

Jan 1, 1972

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor -- will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Feb 24, 1997

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000