Search Documents

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By Greg Hodges

Sand-and-gravel aggregates have become the number-one, nonmetallic-mineral resource in the world. Surficial aggregate deposits of economic size are becoming increasingly rare in most parts of Canada. In southern Saskatchewan, this is especially true, and detection and delineation of intertill sand-and-gravel deposits with airborne electromagnetic (EM) surveys have proven very successful. Airborne and ground geophysical surveys detect such deposits by their resistivity contrast relative to the surrounding clay-rich soils. Dighem helicopter-borne electromagnetic surveys map soil variations over a large area quickly and cost effectively, greatly reducing the cost of detecting and mapping deposits compared with traditional methods (air-photo interpretation, ground EM, and drilling.). The multiple-frequency EM system used by Dighem can map variations both horizontally and vertically. Magnetic data collected simultaneously are useful in mapping bedrock geology. Both resistivity and bedrock maps aid in the important task of reducing drilling costs and person-hours in the field. The results of the survey are presented as maps of ground resistivity, which are relatively easy to interpret. These maps are produced in the field at the time of the survey, making quick follow-up of the survey possible. Airborne EM surveys can map the extent and depth of aggregate deposits more effectively than is practical from the ground. Since aggregate deposits can vary tremendously in a very short distance (<300 m) large-area EM maps can show both local area variability and also help develop intertill trends. A test survey for the Saskatchewan Highways and Transportation Department over a 3-km by 5-km area mapped all the known deposits as well as some unknown deposits, subsequently proven by drilling. The test-survey data show that the method not only detected the deposits, but also gave an estimate of the shape (volume) of each of the deposits. Comparison of the data to drill sections shows excellent correlation. Theoretical modelling demonstrates that the multifrequency system can discriminate sand and gravel from bedrock ridges. Since the successful test work, about 725 km2 of ground have been surveyed, resulting in the discovery of four new deposits, which can be used immediately, resulting in significant savings for the Saskatchewan government and taxpayer.

Jan 1, 1999

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By Michael G. Li

Prediction of acid rock drainage (ARD) for low-sulphide, low-neutralisation potential (LSLNP) mine wastes is methodologically different from that for normal sulphidic mining wastes. In this paper. LSLNP wastes are conveniently defined as those with S2 < 1% and ABA-NP2 < 20 kg CaCO3 eq/t. The distinctiveness of ARD prediction for LSLNP materials originates from their frequently low oxidation rates and is mainly attributable to two reasons. First, the utilisation efficiency of available carbonate neutralisation potential (CNP2) rapidly deteriorates when the sulphide oxidation rate per unit mass of waste drops below a certain level. Reducing the flushing rate of a waste has the same effect as increasing the oxidation rate. Second, silicate neutralisation becomes increasingly important as oxidation rates diminish, and can no longer be ignored in LSLNP materials as it often is for normal sulphidic mine wastes. In this paper, the effects of oxidation rate, pore gas CO2 partial pressure, and flushing rate on ARD prediction for LSLNP materials are theoretically demonstrated with the help of modelling using the computer program MINTEQA2. A new methodology for ARD prediction for LSLNP materials is presented in terms of a prediction procedure. Finally, a case study is given to validate some of theoretical aspects discussed and to illustrate the use of the newly proposed ARD prediction procedure.

Jan 1, 2000

By R. E. J. Putman

The past ten years have witnessed substantial development of electronic equipment for execution of process control functions. The methodology of giving instructions to the data-handling system and the organization of the system, both the equipment and instruction coding taken together, have developed simultaneously. Examples of the technology specific to the mineral processing industry can be cited. Approaches to system design developed for the Pinto Valley concentrator incorporating slave and master data processing have been described by Arney, and his associates (1974). Madge (1970) has described the hierarchical systems employed at the operations of Cominco Ltd. The Kennecott Garfield smelter is controlled by a system of microprocessors linked to a general purpose data processor (Marchant, et al., 1977). These systems provide innovative approaches to couple advancing technical capability in electronic data processing to the objectives of process management. The current state of the art described in this chapter is certain to require updating in the 1980&apos;s with the advances in technology anticipated.

Jan 1, 1979

By David Morrison

On the Corramandel Peninsula of New Zealand, the Waihi Gold Mine has undergone a major redevelopment. The upgrade included the construction of two very large overland belt conveyors, both rated for a capacity of 6000tph. The first of these conveyors (CVR2) traverses a total of 1600m over undulating terrain, including a significant section running through tunnels. A large hill is climbed, just after the mid-section of the conveyor run, before dropping back down prior the discharge point. The second of these conveyors (CVR8) traverses 1100m along an alignment with a horizontal curve, a number of vertical curves and a significant lift before the discharge point. The CVR8 conveyor also included a shuttling head pulley arrangement. The mine they service is inside the town of Waihi. The conveyor alignment runs through the town and out to the metallurgical process site on the outskirts of the municipal area. This paper documents the engineering process that took place in the design of these conveyors. The Martha Hill mine in Waihi, New Zealand is unique. The mine is placed in the township. Consequently there are quite stringent environmental limitations on the mine&apos;s operation. In [Figure 1] the proximity of the mine to the town is shown. In the top-centre of the photograph the alignment of the existing smaller overland conveyor can be seen leading from the mine to a tunnel through the hill in the background.

Jan 1, 2000

By Samuel B. Romberger

During the formation of most epithermal precious metal deposits geochemical changes can be characterized by the introduction of large amounts of silica, minor amounts of sulfur, and trace quantities of gold, silver, and other metals. During the same process, large amounts of alkalis and alkaline earth elements, such as sodium and calcium, and sometimes aluminum are removed from the rocks. In deposits hosted by carbonate sedimentary rocks large amounts of carbonate may be removed before or during the silicification process. Small amounts of iron may be introduced by the mineralizing solutions, however, in most epithermal deposits this may be a relatively immobile component and is locally derived. The results of these changes are deposits consisting of up to 90 to 95 percent silica as quartz veins, breccias, silicified host rocks, and jasperoids containing a few percent sulfides, mostly pyrite, and a few parts per million gold and silver. Other minerals commonly but not always present are barite, arsenic, antimony, or mercury sulfides, and tellurides. Often gold shows a spatial, and therefore an apparent genetic, relationship to pyrite in primary ores. Alteration and gangue assemblages sometimes include sericite and/or adularia, and parts of the deposits may contain alunite and/or clay minerals. Even though the value of these deposits usually lies in their gold content, silver is usually present in larger quantities than gold (Romberger, 1990). Based on these general characteristics observed in a large number of epithermal deposits, together with processes occurring in active geothermal areas to which they are often genetically linked (Henley, 1985), a model is proposed whereby deposition occurs along a subhorizontal zone separating environments of contrasting chemistries. The upper environment is characterized by oxygenated acid waters and the deeper environment by a reducing near neutral aqueous system. The model describes the chemical changes occurring as a result of mixing and/or boiling within this zone. It builds upon the physical models proposed by Romberger (1988a) for disseminated gold deposits and Bonham (1988; 1989) for volcanic rockhosted deposits.

Jan 1, 1990

By Winfield G. Wright, Philip L. Verplanck, Philip L. Hageman, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

Geological, hydrological, and geochemical information synthesized in a Geographical Information System (GIS) for water and rock surrounding South and Middle Forks of Mineral Creek, northwest of Silverton Colorado, was analyzed to distinguish between the natural and the mining-related sources of metals to dace waters in the watershed An important natural source of metals to surface water emanates from a porphyry molybdenum deposit south and upslope from the Middle Fork of Mineral Creek. Interaction of surface and ground water with fractured, altered rocks and permeable, Quatemay-age surficial deposits produces downstream water quality that does not meet current State of Colorado water quality standards for metals and pH. GIS site characterization and three-dimensional modeling distinguish surficial deposits as volumetrically substantial, significant sources of naturally occurring metals that strongly influence water quality and complicate ongoing mine-site mitigation efforts. Our findings indicate that regional hydrologic and geologic information needs to be evaluated before realistic water quality guidelines are established and mitigation recommendations are confidently implemented.

Jan 1, 2000

By Charles H. Jacoby

In 1960 the management of International Salt Company made the decision that all waste material from the Watkins Glen plant would be stored in underground salt cavities. The cavities which they contemplated using had been depleted of salt to a point where continued operation would have impaired their structural stability. Originally, the waste to be disposed of included vacuum pan bleeds, cinders, contaminated salt and sewage. It was proposed that this material, in a slurry form, was to be injected into the salt cavity through one of the abandoned wells. Brine, displaced from the cavity, was to be recovered from an adjacent well and subsequently injected into the Cherry Valley limestone, This Cherry Valley limestone which underlies a large portion of north central New York contains a connate water with high concentrations of ammonia, hydrogen sulphide and the chlorides of calcium, magnesium and sodium. A number of questions were immediately raised on various aspects of the technical feasibility of the project. Of major concern was the buildup of insolubles adjacent to the bore of the injection well. Another pertinent question was the carryover in the displaced liquor of finely-divided, mechanically-suspended particles. Criticism was leveled at the inclusion of sewage. Engineering studies were started by the company&apos;s Mineral & Mines Development Department and on April 3, 1961 a preliminary feasibility report was issued.

Jan 1, 1973

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By K. Bragg

During the last several years considerable discussion has taken place on the long term aspects of uranium tailings management. These discussions have centered around a variety of topics which in turn lead to a variety of opinions. In order to come to grips with the various differences of opinion and points of view, the Atomic Energy Control Board has decided to prepare, as an interim measure, a list of proposed close-out criteria for uranium tailings management facilities. It is important to keep in mind that the criteria set out in this paper are proposals and are intended to initiate a continuing dialogue between the uranium mining industry and the various regulatory and government agencies. It is envisaged that this dialogue would continue for a period of from six to twelve months after which some final form of these criteria would be issued and applied to the active uranium mining facilities. In attempting to understand the reasons why the Atomic Energy Control Board has decided to propose these criteria now instead of at some future point in time, it is necessary to look at a number of existing facts. One of the most important of these is that something in excess of one hundred million tonnes of tailings currently are placed in various tailings management facilities. Furthermore, the rate at which tailings are being deposited into such management facilities is on the increase and this increase is expected to continue over the next five to ten years. The management of these tailings is currently covered under the Mine Facility Operating Licences issued by the AECB. Implied within these licences and supporting documents leading to them, are requirements for the conceptual approach to be used at abandonment. There is however, no current requirement for a detailed study on the engineering or financial aspects of such abandonment procedures. This is a gap which the Board feels must be addressed. There are, at this time, various initiatives underway both in Canada and within the international community which are attempting to address the problems and concerns of the very long term management of tailings. For example, current research in Canada which is composed of two components, one by the AECB dealing with purely regulatory aspects and a second major coordinated program under the direction of the Department of Energy, Mines and Resources and in particular by CANMET is going to deal with the technical problems. On the international scene

Jan 1, 1980

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state&apos;s population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By A. Ersoy, M. D. Waller

Because of a shortage of diamonds for the drilling industry in the 1970s, efforts were made to develop synthetic diamonds. The resulting development of polycrystalline diamond compacts (PDC) enabled the evolution of a new generation of rotary-drilling drag bits. Bits based on PDC cutters were very successful in drilling soft, abrasive and medium strength rocks. However, because of their thermal instability, they failed rapidly when drilling hard rocks. Thermally stable diamond (TSD) was then developed for hard-rock drilling. The rate of penetration (ROP) and bit life significantly influence the drilling cost. The ROP and the life of the TSD bits or cutters are affected by a number of complex factors. However, in laboratory testing and infield operations, the principal factors that need to be considered in predicting drilling and wear rates are bit design characteristics, bit operating parameters and the characteristics of the penetrated rock. These characteristics are comprehensively reviewed for both laboratory and field drilling results using TSD bits. Optimization of these parameters increases the drilling rate, prolongs the bit life and reduces the drilling cost.

Jan 1, 1998

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By D. Piper, J. Noble, M. Richardson, J. Wojcik, L. W. Cope

L. Cope Welcome. I am pleased to see so many people interested enough to stay until this last session of the last afternoon of the convention. Of the people on the panel here, everyone has done everything in placer mining, but we have tried to sectionalize it with each one of us taking a particular portion. Any one of us could probably answer any question. I am very pleased to see some well experienced people in the audience. To start the discussion, Joe, can you give us a brief comparison of pit and drill sampling? J. Wojcik They both have their place. If you expect your deposit is something that is going to have widespread fairly uniform grades, then the pits may be the way to go. If you are going to have something you have to trace for several miles down the river valley, you can&apos;t do it with pits and do a proper sampling job. C. McLain Joe, the end result of all of this is to go ahead and mine it if it is a deposit. Do you try to relate your drilling results to something in mining itself against the recovery, because the drilling in different types of ground will give you different kinds of recoveries, and mining in the end is what you are going to do? Do you try to relate this to your mining method?

Jan 1, 1992

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By L. A. Puchkov

The paper presents the outline of the results in the algorithms and software of the microprocessor-based system for the powerful drugline bucket automatic motion, as well as the technological process control and functional diagnostics of the electrical equipment. The system is, aimed at the increasing both the draglines&apos; working efficiency and the professional, competence of the operators. The excavator-dragline, equipped by the automatized operation, diagnostic and information processing system, possesses considerable technological: flexibility, which can widen therefore its field of application. The tasks of the dragline bucket motion optimal operation, programming of the excavation and overburden dumping processes, as well as the tasks of the control and the analysis of the technological parameters and the diagnostics of electrical equipment conditions, are defined in the paper. In our paper we present the results of these tasks being solved, providing the algorithms of the main mechanisms for the automatic operation for the swinging bucket controlled motion, the algorithms of the statistical analysis of the working efficiency parameters the algorithms of the diagnostics for electrical driving systems. The algorithms of the motion operation are constructed using the predicting dynamic models. The diagnostic algorithms at the normal working conditions form a number of algebraic invariants always equal to Ø with the accuracy up to when the electrical equipment is parametrically adequate. The algorithms of evaluating and analysis of the excavation efficiency make use of the direct measurement and analytical identification. The working condition and quality of the operation and control algorithms are investigated by simulation and natural testing. The results of the mathematical simulation of the bucket motion (with the 20 m3 capacity) of the excavator-dragline with the boom of 90 m in length are given in the paper.

Jan 1, 1992

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.&apos;s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By James Stewart

"THAT WHICH WE CANNOT SEE" INTRODUCTION Often it has been stated that the greatest of all fears is fear itself - fear created only by that which we cannot see or by that which we fail to understand. The elimination or minimization of fear can best be accomplished by a thorough understanding of the underlying causes of the fear. As related to the mining industry the omnipresent fear is the dread of acquiring cancer through accumulated exposure to "that which we cannot see" - radioactivity. The understanding of the resulting exposure effects can best be obtained through acquisition of authentic data and the subsequent analysis of the same by a group of highly qualified specialists. I may point out that the nuclear industry and its source, uranium mining, greatly surpass any other industries in the degree of public awareness as to its potential environmental effects. Public out-cry has always influenced major decisions relating to how industries conduct their operations and much of their effort has resulted in many changes. The issues of health and safety in the mining industry have created considerable public concern, but intense concern to those of us directly involved within the industry. Increasing concern regarding the effect of human activity on the quality of the outer environment of air, land, and water has developed within the past two decades. There is now a growing concern about the health and safety of persons at work in their inner environment, of their working-places in industry. Hearings and investigations conducted in Canada by three appointed "Royal Commissions" have all confirmed that this concern is well justified when focused on the health and safety of workers in our mines. REGULATORY CONTROL OF URANIUM MINING OPERATIONS In Canada, the ownership of mineral resources and the control of their extraction, except for uranium, is vested under the "British North America Act" in the provinces. In all provinces the statutory basis for health and safety provisions in the mining industry can be found in the provincial "Mining Acts" with each province assuming the responsibility to produce its own "Mining Act". In particular, all of the Mining Acts in Canada place upon the management of a mine the responsibility to ensure that provincial provisions are met. The "Federal Register" and mining companies parallel this arrangement in the United States. Equivalent legal

Jan 1, 1981