Search Documents

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K. A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in the Fe-Pb-C system are 95.4%Fe-4.5%C-0.1 %Pb and 99.9%Pb-0.I%Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx [mass%X in molten Pb]/(mass%X in molten Fe), are 2.2, 2.2 and 1.4, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003

By J. M. Casas

This work presents the development of an ionic equilibrium model and its use to simulate the distribution and concentration of chemical species (speciation) in sulfuric acid - cupric sulfate solutions in the 0-2 pH range, 0.1-10 gpl copper concentration range and 15-45°C temperature range. The model consists of a set of equations which represent the equilibrium relationships for the ionic reactions and the mass balances for the components present in the system. The effect of ionic strength was taken into account by correcting the equilibrium constant in concentrated solutions. Several species can be formed at different pH and temperature values, the principal being: HSO-4, SO42-, CuSO4(aq), Cu2+, and H+ in order of increasing solution acidity. Simulations show that concentrations are highly dependent on pH. The sulfuric acid speciates mainly as bisulfate ion (HS0-4) and hydrogen ion (H+) at pH values lower than 1. The model presented in this work can be applied to predict and analyze the solution composition in electrolytic copper processes such as electrowinning, electrorefining and electrodialysis, as well as the purification of various industrial solutions.

Jan 1, 1999

By M. Huang

A conductivity-based sensor for on-line measurement of free acid was recently built. This sensor is suitable for high ionic strength solutions and its corrosion-free operation is based on induction currents. It has been tested against literature data and measurements made using a previous developed contact-type conductivity cell, with an average difference within 1%. The electrical conductivities of H2SO4?H2O, H2SO4?MgSO4?H2O and NaCl?Laterite-H2Osolutions at temperatures up to 250 °C were discussed. It was found that the solution conductivity depends on various factors, such as the electrolyte concentrations, the type of electrolytes, temperature and the amount of dispersions. A semi-empirical model was developed to account for all the factors discussed. This model was further tested on actual process solutions from the hydrometallurgy of nickel where sulphuric acid solutions containing a variety of metal sulphates and solids. The average difference between the estimated acid concentration from this model and the one from titration was generally less than 5%, which is excellent for industrial applications.

Jan 1, 2006

By T. Watanabe, T. Fujiwara, S-Wan Song, Y. Nakagawa, R. Teranishi, M. Yoshimura

"We have tried a new method to fabricate cobalt oxide films onto porous films directly by an electrodeposition method at low temperature. The porous substrate films (membrane-filters and paper) were placed between a LiOH solution and a CoSO4 solution and treated under electricalcurrents of ~1 mA/cm2 using carbon cathode and anode. Effects of temperatures, flow rates and electrical currents have been investigated. As a result, we found that the LiCoO2 films and Co3O4 films were successfully fabricated on paper and/or porous PTFE filters at 120 °C, while CoOOH films were deposited at 80 °C. Furthermore, LiCoO2 films did not cover whole the substrates, but was fabricated just over the anode. The chemical reactions of electrodeposition were also considered from these results.IntroductionRecent agreements on global environment require rapid progress of low energy and low waste processings for the fabrication of thin films that succeed to the mass production with the high consumption of the fossil fuels (such as physical vapor deposition°, chemical vapor deposition2), dip coating with firing3) etc.). The total energy consumption in aqueous systems should be the lowest among all these processing routes, because a much lager excess of energy is necessary to create melts, vapor, gas, or plasma than to form an aqueous solution at the same temperature4)The ""Soft Solution-Process"" (SSP) was one of the best concepts to realize the low energy and low waste fabrication of inorganic materials. 5) Generally speaking, SSP gives similar results to any other processing using fluids (such as vapor, gas plasma) and/or beam/vacuum processing. However, the total energy consumption of all these possessing routes should be the lowest in aqueous systems, because a much larger excess of energy is necessary to create melts, vapor, gas or plasma than to form an aqueous solution at the same temperature (Fig. 1). This idea can be easily demonstrated, using the simple example of BaTiO3. The energy diagram for the formation of BaTiO3 from various precursors is shown in reference 4. The driving forces (AG) for representative synthesis reaction of (1), (2), (3), (4) and(5) are 38, 727, 3685, 17 and —14kcal/mol, respectively at room temperature. 6' 7"

Jan 1, 2000

By C. D. Adams, R. T. Tuenge, C. N. King, J. A. Samuels, B. F. Espinoza, R. C. Dye, C. F. Schaus, D. C. Smith, N. M. Peachey

"Recently, doped calcium thiogallate (CaGa2S4) phosphors have been investigated for use in electroluminescent flat panel displays. The current technique used for the deposition of thin film calcium thiogallate is sputtering. Unfortunately, this requires a high temperature annealing process to provide the desired crystallinity of the phosphor. Recent efforts have focused on the possible use of metal-organic chemical vapor deposition (MOCVD) to produce the CaGa2S4 layer. The use of MOCVD provides an attractive alternative to sputtering since it does not require heating above the strain point temperatures of the glass substrates used for the display panels. To accomplish this, the deposition of both Ga2S3 and CaS is investigated as these compounds are intermediate steps in the development of the phosphor deposition. Uniform, crystalline films of both Ga2S3 and CaS were deposited and the process shows promise for successful deposition of the CaGa2S4 phosphor.IntroductionThe lack of a satisfactory blue phosphor having sufficiently high luminances at low power has hampered the development of high resolution flat panel displays. Recently, a new series of blue emitting materials have been investigated for use in thin film electroluminescent (TFEL) devices. l ,2,3 These phosphors are based on a series of alkaline earth thiogallate host materials of the form MGa2S4:RE where M can be either calcium, strontium, zinc, or barium and RE is a rare earth ion. A full-color VGA TFEL panel using CaGa2S4:Ce as the blue phosphor has recently been fabricated and tested. l This FPD provided a luminance of 10 cdlm2 at 60 Hz. The enhanced blue in this display allowed its color capabilities to approach those of the conventional CRT.The method of depositing the phosphor onto the display panels in these test devices has been sputtering. Unfortunately the phosphor as deposited does not possess the crystalline properties required for optimum luminance. The crystalline structure is achieved by subsequent annealing of the deposited material. Although this post deposition anneal provides the desired crystal structure, it occurs above the strain point temperature of ordinary glass. Consequently, the implementation of these phosphors requires the use of glasses capable of withstanding high temperatures, adding to the cost of the final display unit."

Jan 1, 1994

By Hongmin Zhu, Guihua Wang, Xiangsheng Wang

"The anode process of carbon electrode in fluoride melt was studied by voltammetry and chronoamperometry. Anode gases were analyzed by gas chromatography on-line during controlled-potential electrolysis. Two peaks were observed on the cyclic voltammograms. According to the results of gas chromatography, the first peak was corresponded to the discharge of residual oxide ions, with the formation of CO and CO2. Discharge of fluoride ions occurred at 4.1 V vs. Li+/Li, and leading to the anode effect. With the occurrence of anode effect, small amount of CF4 was detected. As the potential reached 4.5 V, CF4 and C2F6 gas evolution occurred, and the current increased to form the second peak.1.IntroductionIn the primary production of Aluminum and some rare earth metals like neodymium, a departure from normal cell operation known as anode effect results in the generation of perfluorocarbons (PFCs), which have high global warming potentials [1]. Owing to the pressure of environmental protection, considerable research has been carried out to clarify the mechanism of anode effect and PFC generation of industry and laboratory cells in the aluminum electrolysis system [2-9]. The common result on PFC generation is that the PFCs are emitted from Hall-Heroult cells only when they are on anode effect. In this article, we selected LiF, the main electrolyte for the neodymium electrolysis [10-11], to perform further investigation on the underlying kinetics of PFC generation and the nature of the reactions at the electrode.2. ExperimentalAll experiments were carried out in an alumina tube reactor, which was filled with high purity helium atmosphere. Spectrographic graphite crucibles were used, which played the dual role of molten fluoride container and the counter electrode. Lithium fluoride was analytical grade. The experiments were carried out at 900 °C."

Jan 1, 2011

By K. Verbeken, E. Wettinck, M. Verhaege

Iron (III) can easily and selectively be removed from acidic sulphate solutions with organo-phosphoric acids like Di-2-Ethyl-Hexyl-Phosphoric Acid [D2EHPA]. Stripping of the iron (III) loaded organic, however, is difficult unless highly concentrated inorganic acid solutions are used. In this paper results are shown for the enhanced stripping of iron from loaded D2EHPA by electro-reduction. The loaded solvent is contacted with a 2 M H2SO4 solution, which is continuously recycled in an electrochemical reactor where iron (III) is reduced to iron(II). As iron (II) is not extracted by D2EHPA, the equilibrium for iron (III)- D2EHPA is shifted towards the aqueous iron (Il)-sulphuric acid solution. The electro-reduction unit is a vessel with separated catholyte and anolyte chambers. The catholyte is the actual stripping solution where iron (III) is reduced to iron (II) on a stainless steel electrode. The anolyte is a 2 M H2SO4 solution where oxygen is evolved on a lead alloy electrode. A sintered glass plug separates the compartments. With this unit, enhanced stripping of iron from the solvent is possible under mild acid conditions [2 M H2SO4], and a concentrated ferrous sulphate solution can be obtained. The results shown have mainly been obtained by studying the parameters affecting the electro-reductive stripping of a D2EHPA loaded organic phase in a batch reactor. From an iron (IH)-saturated 20 vol. % D2EHPA solvent containing ~ 12.5 g/1 Fe (III) over 90% of the iron can be stripped in one stage with a 2 M H2SO4 solution at 50°C. It is shown that in this way it should be possible to obtain a concentrated ferrous sulphate solution which can be processed downstream to recover a pure iron product.

Jan 1, 2000

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

By F. Ajersch, P: Tsantrizos, K: Shanker

"TiN films have been deposited on various substrates by a novel reactive plasma technology. In this process, a nitrogen source (NH3 or N2) and TiCl4 are reacted in the jet of a plasma torch, and are deposited onto a substrate forming TiN films at a high growth rate ( > 2µm/min). It was found that the process parameters strongly affect the microstructure, thickness, density, and growth rate of the TiN films. These parameters include source of nitrogen (NH3 or N2, N/Ti ratio, temperature of substrate, and spray distance. In general, it was found that thick and dense coatings were deposited when the N:Ti ratio was kept low, and the substrate temperature was high. Also, for the series of conditions investigated, NH3 was found to give much better results than N2•. The limitations and advantages of this technique are also discussed in this paper.IntroductionTiN is an extremely hard material and is used in many wear applications, particularly as a protective coating on cutting tools to extend their Iife(1.2). Owing to its excellent chemical stability, TiN is also frequently used as a diffusion barrier in the electronics industry for sub-micron Al/TiN/Si ohmic contact systems (3) or as a coating on high-temperature resistant alloys in gas turbine applications (4), based on its good resistance to oxidation. Other applications include decorative coatings in the jewelry industry, and specialized applications such as solar energy absorbers and transparent heat mirrors(5).TiN films can be deposited/formed using various techniques. The main techniques of deposition are CVD (Chemical Vapour Deposition) and PVD (Physical Vapour Deposition). Each of these techniques can have many variations in equipment characteristics, reactants as well as a range of process parameters (pressure and temperature). In the CVD process, TiN is generally deposited onto a heated substrate where a chemical reaction takes place. The reaction can be one of reduction(6) (e.g.: TiCI4 + 0.5N2 + 2H2 --> TiN + 4HCI), of thermal decomposition(7) (e.g. decomposition of titanium dialkylamide), or of displacement (e.g. TiCI4 + NH3 --> TiN + 3HCI + 0.5CI2)' The displacement and reduction reactions are the most common."

Jan 1, 1994

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013

By Shantanu Chakrabarti, Khursid Alam Khan

"Globally, the use of metallic coated steel sheets in the automobile industry is increasing. The sheet should have excellent formability, weldability, paintability and corrosion resistance. Since bare cold rolled steel sheets have certain limitations, application of galvanized steel sheets is steadily expending. Galvannealed steel sheet fulfills all requirements and has become of major interest in the automobile industry.The success of Galvannealed (GA) steels in the body-in-white depends upon material design and parameters of various processes involved, like cold rolling, continuous annealing, hot dipping and galvannealing. In the present work, powdering resistance, one of the important product characteristics of GA, has been studied and a relation is established between the process parameters and the powdering value. The product obtained through optimization of the process parameters have been successfully used by major automotive producers without any powdering problem, for internal as well as external automotive applications.IntroductionThe present automotive industry demands that steel for the auto components should have excellent formability, weldability, paintability, corrosion resistance etc. In addition to this there is specific requirement for some particular components like high surface quality for skin panels. Corrosion resistance of panels is important requirment which determines the life of the particular component and brand value of the automotive. Among all the zinc based steel coating used in the automotive industry coating produced by Galvannealing process has received most attention because of its excellent weldability along with superior corrosion resistance and better paintability."

Jan 1, 2012

By H. J. Garcia

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. Initial sodium cyanide concentration was 300 ppm at pH 10.5. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. The activation energy and the frequency factor were determined to be { A }Ea = 5.45 Kcal/mol and A = 1.28 x 10-2 sec-1, respectively. Based on these values, thermodynamic properties of an intermediate activated complex were assessed. All tests resulted in cyanide concentrations less than 0.1 ppm in about 35 days at 250C, whereas at 350C the time of biodegradation to reach this cyanide level was 30 days. Kinetic data were also established to relate biodegradation to amount of inoculum. The maximum theoretically-attainable rate, Vm , and the optimum amount of inoculum, K , were determined to be 4.8 x 10-4 M NaCN/day and 7.5 % of amount of inoculum. With respect to the mechanism of biodegradation, cyanide was shown to decompose to carbonate, bicarbonate and ammonia. Titrimetric analyses revealed concentrations of 5.6 x 10-3, 4.8 x 10-3 M, and 70.2 ppm for carbonate, bicarbonate and ammonia, respectively. The average cell population was determined to be 3.75 x 108 cells/mL.

Jan 1, 1994

By Wenjie Zhu

Chromite ore processing residue (COPR) is a hazardous waste containing high concentration of chromium. We describe here a pioneer trial of detoxification of COPR in column reactor with an indigenous chromate reducing bacterium Leucobacter sp. Ch1, which showed high chromate reducing ability at high pH. Under the optimum conditions, at 30°C and pH 10.0, pH of leachate decreased from 10.3 to 8.3, and Cr(VI) concentration in solution decreased to zero mg L-1, and 76.4% of Cr(VI) was removed from COPR samples. The leaching toxicity of detoxified residue was 1.1 mg L-1 that was lower than national standard of China.

Jan 1, 2008

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Oscar J. Restrepo

Through reactions in solid form at high temperatures, using iron oxide (Fe3O4) and chromium oxide (Cr2O3) in fixed proportions as precursors, the compound was synthesized with spinel structure type FeCr2O4. For different temperatures synthesis was conducted the characterization of the material obtained through X-ray diffraction (XRD), spectroscopy UV-VIS-NIR, scanning electron microscopy (SEM), energy dispersion analysis of X-ray (EDX) thermal analysis (DTA / TGA) and magnetic susceptibility of alternating current. The changes in the spectra of reflectance changes are related to the phase identified, the degree of crystalline structure, the spatial order of cations and the magnetic behavior obtained.

Jan 1, 2009

By Xi Yun Yang

Ultrafine (0.1µm) spherical magnetite powder was prepared successfully by hydrothermal reaction of ferrous sulfate and sodium hydroxide with activated pyrite as reducing agent in the temperature range 120-140?. XRD and XPS analyses indicate that pH value and pyrite amount have a direct influence on the composition of the product. Stoichiometric Fe3O4 can be obtained only when pH value is 12 and the molar ratio of pyrite/ferrous sulfate is 1:1.8. The hysteresis loop of Fe3O4 shows a ferromagnetic behavior with a saturation magnetization of 75.2 emu/g and a coercivity of 152Oe.

Jan 1, 2006

By Sang-Joon Kim, Hae-Geon Lee, Hyun-Jin Cho

"Decarburization phenomena on the surface of liquid iron have been simulated by numerical method and the results were compared to the experimental data. During the DeC process in a converter, a large amount of splashed droplets are generated from the top surface of the bath and consequently the reaction surface area is increasing tremendously. Since the decarburization mainly occurs at the interface, it is important to understand the reactions on the liquid iron droplets. The flow and species concentration fields around liquid droplets taking into account the reaction of carbon with oxygen at the interface were calculated by a commercial CFD code FLUENT which solving multiphase Navier-Stokes equation with Volume Of Fluid method, species transport equations and energy transport equation. The initial carbon concentration was fixed to 4 wt% and the concentrations of oxygen in the atmosphere were varied from 5 to 50 wt%. As comparing the numerical calculation with experimental data written in the reference, the results have a good agreement for decarburization rate.IntroductionIn a primary steelmaking process, one of the main functions is to decarburize from hot metal and the 4% of carbon is decreased to about 0.5% of carbon. Even though there are some possible reactions leading to the removal of carbon from hot metal, the main reaction occurs on the free surface by direct oxidation of carbon at the gas-liquid interface with producing the carbon monoxide gas. In many metallurgical processes involving a jet impinging onto a steel bath surface, especially in a Basic Oxygen Furnace (BOF) converter, it is important to understand the behavior of molten iron droplets splashing out of the steel. The iron droplets are generated by an oxygen or air jet blowing and it increases the total surface area of liquid iron tremendously. Since the decarburization reaction is mainly affected by the surface area, it is necessary to verify the decarburization phenomena around the splashed droplets from liquid iron in order to allow an analysis ofBOF process possible."

Jan 1, 2011

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988