Search Documents

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By U. Kammer

The reduction of the lead content in the separator fraction produced during the mechanical processing of spent lead-acid batteries is an important environmental and economical issues. The reduction of lead down to less than 1 percent is very difficult using hydroseparators that are common in battery recycling facilities. Very promising results were achieved performing experiments on a test rig using a new technology in battery treatment: a discharge-type jigging unit. The materials is fed onto the jigging bed and transported through the machine. Due to the intensive movement of the feed, an additional washing effect is also obtained in addition to separation of the lead and plastic fractions. The knowledge gained from this development work at UVR-FIA GmbH in Freiberg, Germany, led to a patent application. This paper focuses on the results of the development work and the start-up and one year's operation of the industrial-scale application at Harz-Metall GmbH in Goslar, Gennany.

Jan 1, 2000

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Chen Dong, Yuanling Gao, Jilai Xue, Jun Zhu, Luxing Feng

"Porous Ni-Ti alloy has many applications in a wide range of engineering areas. The porous NiTi alloys were prepared from Ti and Ni powders in sintering process under argon atmosphere. The major chemical compositions of the sintered Ni-Ti body were Ni Ti, Nh Ti4O and Nh Ti, respectively, the internal pore structures were characterized by image analysis technique, which were dependent on various processing parameters such as sintering temperature, amount of poreforming agent, forming pressure, etc. The results show that the porous alloy samples had the characteristics of uniform pore and high open porosity; pore-forming agent and sintering temperature are important factors in porous; pressure affected the sintered products' pore, by affecting the combination of alloy powder with pore-forming agent.IntroductionPorous Ni-Ti alloy materials exhibit not only excellent shape-memory and superelasticity, high yield strength and ductility, good corrosion resistance and biocompatibility, but also have low density, low stiffness, and high energy absorption rate due to their porous structures [1]. In recent years, these porous Ni-Ti alloys have found applications in a wide range of engineering areas, such as bone implants [2-4], impedance-matching connectors [5], energy-absorbing structures [6,7], separators [8] and actuators [9], etc.Pore characteristics can play very important role in determining of the performance of porous NiTi alloys. For example, when the alloys are used to repair or replace hard tissue implant material, the pore shape and size not only determine their mechanical properties, but also have great effect on the fluid transmission of human body. The pore characteristics can also influence the stressstrain behavior of the porous Ni-Ti alloy and, thus, strongly affect their mechanical properties, superelasticity, and fracture mechanisms [10].In this study, the Ni-Ti alloys with high porosity were prepared in a powder sintering process under argon gas. The pore characteristics were investigated using SEM, XRD and image analysis techniques, especially in association with the content of pore-forming agent, sintering temperature and compacting pressure."

Jan 1, 2011

By C. Isaac Garcia, Sihai Jiao, Anthony J. DeArdo

"A practical model based on the Hill analysis has been developed to calculate the Lankford value of interstitial free (IF) steels and its distribution in different rolling directions, by considering only a few selected texture components. The Texture Intensity Ratio (TIR), i.e. (111 ) /(100), was used in the model to describe texture. By using the new TIR parameter, the texture-based prediction models can be used more easily to predict the Lankford value in a rather straightforward way.IntroductionThe deep drawing capacity of sheet steels is generally indicated by the Lankford value, which is mainly determined by the texture in steels1. Traditionally, various models derived from the Taylor model are employed to calculate the Lankford value from the texture2-4. In such models, the plastic deformation of steel is assumed to be the result of the slip of dislocations in certain slip systems, i.e., by either pencil glide or restraint glide. The slip direction is the <111> direction. In the case of pencil glide, the slip is thought to be possible in all crystal planes with the <111> crystal direction. Assuming the material is elongated in the X1-direction by d n and compressed in the X2 and x3-direction by qd n and (l-q)d n, respectively, corresponding to a deformation tensor"

Jan 1, 2001

By Hua-qing Li

Electromagnetic stirring process effectively improves the casting quality of metals. In this paper, the physical simulation experiment, in which the molten copper is displaced by mercury, was designed. The factory test parameters were determined according the simulated data. The flow behavior of the mercury to be stirred as well as the relations between the microstructure of plate blanks and the current parameters were analyzed. With an appropriate electromagnetic stirring, the inverse segregation of tin for C51900 alloy plant blank reduces from 15 % ~ 30 % to about 5 %, and the proportion of equiaxed grain rises to larger than 30%.

Jan 1, 2009

By Toshio Suzuki, Machiko Ode, Won Tae Kim, Seong Gyoon Kim

"The Ostwald ripening and growth and coarsening of the secondary dendrite arm are studied using a phase-field model. The phase-field parameters are obtained at a thin interface limit proposed by Kim et al. In Ostwald ripening analysis, the difference of the concentration due ·to· the curvature effect is shown. The third power of the average particle radius Rav is proportional to time and the ripening constant shows a good agreement with the value by Deppers et al. The particle radii distribution shows the transition behavior to attain a self-similar stationary shape. The growth and coarsening behavior of the secondary dendrite arm is also analyzed using a phase-field model. The estimated arm spacing and its dependence on time are in good agreements with experimental data.IntroductionThe ripening or coarsening process controls the microstructure during the late stage of solidification. The ripening phenomena are recognized firstly by the Ostwald [1]. The first quantitative analysis for the Ostwald ripening in the limit of vanishing solid fraction was provided by Lifshitz, Slyozov and Wagner (LSW) [2,3]. In their study, that the mean radius grows proportional to the cubic root of time and the size distribution of precipitations shows a ""self-similar"" shape are shown. Most of the studies for the Ostwald ripening confirm or predict these two general rules above. In case of finite solid fraction, the general rules are observed but the ripening constant is larger and the self-similar shape is wider than the LSW prediction respectively [4-6]. To analyze· the high solid fraction system, the theories that consider the solute field correlation are proposed [4,7-8]. In the theory, however, since the particle is treated as the point, the effect of the concentration field deviation from the monopole field should be taken into account. Recently the numerical simulation, in which not only diffusive transportation of solute but also convection effect is considered, has been done using a phase-field model [9]."

Jan 1, 2000

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By Samuel Senanu, Benjamin Agyei-Tuffour, Lifeng Zhang, Eivind Øvrelid, Adegboyega Nathaniel Femi

"The solar grade silicon ingot produced from directional solidification process usually pushes the impurities to the top and finally cut off and discarded, which leads to material loss. The hard inclusions lead to wire breakages during the cutting of the ingot in wafers. The main kinds of inclusions found in solar grade silicon have been investigated using vacuum filtration: needle-like Si3N4 and lumpy SiC inclusions. Clusters of SiC inclusions and Si3N4 are also found. Surface observations of the scraps before polishing reveals that Si3N4 inclusions are usually bigger and in some cases can be about a few millimeters. SiC inclusions are usually smaller, ~200µm but can be ~500µm in some cases. Inclusions observed after filtration are mainly SiC with diameters ~10µm. Through the vacuum filtration, 99% inclusions can be removed 99%. The possible mechanisms of filtration are cake filtration for the larger sized Si3N4 and SiC inclusions and deep-bed filtration the SiC inclusions. For the directional solidified silicon ingot, an approximate distance of ~10mm gave an encouraging cutoff thickness. The inclusions sizes were below 10µm. Introduction The search for an alternative source of energy to fossil fuel has led to a dramatic increase in the demand for solar energy due to its high dependability (abundant in nature) and environmental friendliness 1). During the last 5 to 10 years, the annual worldwide production of solar cell by the photovoltaic industry has increased to an annual rate of 30 to 40 percent 2). A necessary condition for the maintenance and even an increase of this growth rate is a decrease in the cost of feedstock for the solar cell production 1). The total international production in 1997 was 130 MW worth more than $500 million. In 2004 the consolidated world total production of PV cells increased to 1146 MW or around. $7 billion (Figure 1) 3). Silicon is currently the most dominant semiconductor material used in the PV industry. As shown in Figure 2 3), solar cells consist of two types of material, often the p-type and n-type silicon. Light of certain wavelengths are able to ionize the atoms in the silicon (causing atoms to either gain or lose electrons) and the internal field produced by the junction separates some of the positive charges (“holes”) from the negative charges (electrons) within the photovoltaic device. The holes are swept into the positive or p-layer and the electrons are swept into the negative or n-layer. Although these opposite charges are attracted to each other, most of them can only recombine by passing through an external circuit outside the material because of the internal potential energy barrier. Therefore if a circuit is made, power can be produced from the cells under light because the free electrons pass through the load to recombine with the positive holes."

Jan 1, 2008

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDSIM metals precipitation system to treat a waste stream containing scrubber blowdown and process water from a smelter operation. The combined stream contained cadmium, lead, selenium, arsenic and zinc, plus some iron and copper. Treatment requirements included meeting stringent mass flow limitations for specific heavy metals. The HDS ? system can reduce the arsenic from 600 ppm to less than one ppm. The process generates a dense sludge that can be reprocessed in a smelter, eliminating the liability associated with landfilling. Flow diagrams and process details are discussed.

Jan 1, 1994

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

By A. V. Tarasov

A flow-sheet for waste-less processing of spent lead batteries comprises mechanized separation of batteries, smelting of the metallic fraction in a kettle, electrothermal smelting of oxysulfate fraction, refining of crude lead and processing of reverts to produce commercial products. Smelting of lead-containing fraction is performed in an electrothermal furnace using a processing technology developed in the Gintsvetmet Institute and differing from conventional processes by the fact that it does not require any fluxing agent (soda); no matte is formed in the process and the amount of slag produced is minimal, because its formation depends only on the ash content of coke and the quality of battery scrap separation. The process has been patented. It has been introduced on a commercial scale in 1.8 MVA furnaces at the plant of A0 "RyazTsvetmet" (Ryazan, Russia). The process has the following main advantages as compared with conventional shaft-furnace smelting and smelting in a short-drum furnace: the process does not require technical-grade oxygen, the amount of process gas generated is minimized ensuring a decrease in lead-containing dust and sulfur dioxide emissions by 3 to 5 times per unit of lead recovered; a decrease in dust entrainment resulting in lower amounts of recycled dust; lower slag yield (a decrease from 20-25% to 3-5%); lower coke requirement (a decrease from 10-14% to 3-4%). Refining of crude lead is performed using conventional technology but there are several unique features for which know-how is available. Processing of by-products of electrothermal smelting and secondary lead refining (slag, drosses, skimmings) and ebonite fraction (crushed battery casings) is performed in a slag-fuming furnace.

Jan 1, 2002

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By Zhongming Ren

"A new process of near net shape continuous casting of metal pipe has been put out. The specialty of the process is that no inner core is used. The principle of the process has been presented, and the effect of several factors on the thickness of the pipe has been investigated experimentally and numerically. It is shown that the temperature and the level of the molten metal, cooling intensity of the mold, and the velocity of casting influenced the thickness of the pipe apparently. In order to improve evenness of the thickness of the pipe, the mold was dedicatedly designed, and special methods were taken. By this process, a metallic material like ""bamboo"" was fabricated.IntroductionMetal pipe is a widely used material. Up to now, many processes have been put out to produce the pipe. However, the processes are usually expensive and inefficient. For instance, the welding pipe, which is most widely used, is produced through continuous casting of slab, rolling of the slab into sheet, and welding, with several times of heating and processing. Continuous casting of pipe can not produce small diameter of pipe, which is mostly needed, due to the inner core. Even though. OCC process is novel in fabricating the pipe with small diameter, it is inefficient. In this paper, the no-inner core continuous casting of pipe was proposed. With this process, pipe with small diameter can be produced efficiently. The influence of several parameters on the thickness and evenness of piper wall. With this process, a ""bamboolike"" pipe was fabricated.ExperimentThe experimental apparatus is shown in Fig. I. It is composed of mold, furnace, melt level adjuster, and dummy pipe. In the process, the level of the melt was adjusted at a proper position, then the mold along with the dummy pipe was inserted into the melt in a certain depth. The melt in the mold began solidifying, forming a solid shell. After that, the dummy pipe was pulled upward in a certain speed, drawing the solid shell out of the mold. Thus, a pipe was continuously cast."

Jan 1, 2000

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The ever increasing number of automobiles and the consequential increase in consumption of tires have generated a pressing environmental issue, concerning the disposal of unserviceable tires. The worldwide disposed of waste tires is approximately 1 billion units per year and this amount is expected to increase by 2% each year. This work presents a microstructural characterization of nanomaterials synthesized in a catalyst system from the effluent of burning waste tire chips in a horizontal two-stage laminar-flow furnace. Controlled combustion of waste tire chips took place at temperatures of 900 or 1000 °C, and stainless steel meshes were used to synthesize the nanomaterials at 1000°C. Produced materials were analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The catalyst meshes were covered by materials with diameters of 20 to 200 nm and lengths of about 40 µm. They possessed structures similar to those of carbon nanotubes.IntroductionThe motor vehicles on the road have been increasing annually. World motor vehicle production in 2009 approached 62 million units. Consequently, the consumption of tires has also been on the rise; about 1.4 billion units were produced around the world in 2007 [l]. The disposal of scrap tires is a serious environmental problem. The worldwide disposed of waste tires is almost 1 billion units per year with an expected increase of around 2% each year. However, less than 7% of produced waste tires are recycled (excluding reuse, retreading or incineration). The waste rubber tires are a thermoset polymer, which cannot be reprocessed like thermoplastics polymers, therefore the recycling of this material requires special techniques that demand big investments [2, 3].A solution to the disposal of waste tires is the sequential pyrolysis/combustion process. Past research showed that waste tires are an attractive potential fuel due the high heating value (29-3 7 MJ/kg), which is comparable, or even higher to those of typical bituminous coals [ 4, 5]. Pyrolysis is a process wherein the material is thermally decomposed at elevated temperatures at the absence of an oxidizing gas. Combustion is characterized by the addition of the oxidizing gases during the process. Several studies indicate that the pyrolysis and combustion processes for the tires treatment have a great energy conversion potential [4, 5, 6]."

Jan 1, 2011