Search Documents

By William Petruk

Mineralogical and image analysis studies have been performed on four volcanogenic base metal ores that contain 0.01 to 4.5 wt% Pb to determine the behaviour of galena during mineral processing. The galena in these ores is fine grained and is poorly liberated in both the primacy and regrind mill discharges. Consequently, low grade Pb concentrates are produced to obtain relatively high Pb recoveries. The Pb concentrates contain many impurities including high amounts of pyrite and sphalerite, and small amount of CU-, As-, Ag-, Bi-, and Se-sulfides. These impurities need to be rejected from the Pb bullion during smelting. The galena commonly contains up to 1 wt% Ag in solid solution with an average of 600 to 1460 ppu for the deposits studied to date. The Ag in galena accounts for up to 65% of the Ag in some ores.

Jan 1, 1990

By Tom McCullough

The purpose of this paper is to discuss the implementation and results derived from installing oxy-fuel burners in a l80 ton copper reverbatory melting furnace. Specific results will be discussed in the areas of melt chemistry, furnace modifications, productivity, process enhancements, and the combustion system capabilities.

Jan 1, 1996

By M. Misra

The volume of low-level contaminated soil at the. Department of Energy's Nuclear Weapon Sites are in the order of several million tons. Most of the contaminants are uranium, plutonium, other heavy metals and organic compounds. Selected Physical separation processes have shown demonstrated potential in COD Centratingthe radio nuclides in a small fraction of the soil. Depending upon the size, nature of bonding and distributions of radio nuclides, more than 90 percent of the radio nuclide activity can be concentrated in a small volume of fraction of the soil. The physico-chemical separation processes such as flotation in a mechanical and microbubble tall column cell have shown, promising applications in cleaning up the high volume contaminated soil.

Jan 1, 1995

By Hui Zhang

The leaching behavior of palladium powder in aqueous solutions containing NaCI or N'H4Cl was investigated. Cupric ion was used as an oxidant for the dissolution reaction. The effect of a number of leaching parameters such as temperature, concentration, stirring speed and surface area on the leaching rate was studied. The leaching system containing chloride and cupric ion was found to be very effective for the dissolution of metallic palladium. Based on the experimental results the overall leaching rate was believed to be controlled by a chemical reaction step. The dissolution rate of palladium was found to be first order with respect to the concentration of cupric ion and second order with respect to the concentration of chloride.

Jan 1, 1996

By Atsushi Shibayama

The aim of this research was to develop a copper recovery process from mine tailings (0.34%Cu) using flotation followed by high-pressure oxidative leaching (HPOL) and solvent extraction. The results of HPOL using the concentrate of mine tailings obtained by flotation under the optimal conditions of the previous study shown that an efficient copper dissolution of 94.4% was achieved in an H2O media, while the copper concentration of PLS reached to be 2.9 g/L. The solvent extraction of PLS obtained from the optimal HPOL showed that 91.3% copper was recovered in stripped solution under the determined optimum conditions, in which the copper concentration achieved to be 44.8 g/L. Finally, a proposed copper recovery process from the concentrate of mine tailings was developed by combination of HPOL and solvent extraction, while a total copper recovery of 86% was achieved.

By Roger N. Kust

Removal of heavy metals from industrial process streams is becoming increasingly important for _the recovery and reuse of values in process tails. Technology has been available for several years which removes heavy metals, from dilute (0.1-3.0 g/L) streams, as hydroxide or hydrated oxide sludges, allowing discharge of washed cakes with up to 60% solids. This paper reports on improvements to this technology which now allows treatment of streams with metal concentrations in excess of 60 g/L while eliminating the need for thickeners. Streams containing copper, iron, aluminum, chromium, nickel, zinc, cobalt and lead have been successfully treated.

Jan 1, 1992

By De-qing Zhu, Zi-fu Gao, Jian Pan

"In order to produce high quality metalized products and prevent from burden cohesion during pre-reduction, self-fluxed pellets were made for COREX process in the paper. The effects of reduction temperature and reducing gas composition on pre-reduction behaviors of self-fluxed pellets are studied. The results show that the prereduced pellets have poor quality and deposited carbon appears when the reduction temperature is between 600°C and 700°C. The metallization rate, reduction degree and compressive strength of prereduced pellets are promoted by the elevating reduction temperature and mole fraction of H2. Pellets reduced by pure H2 at 800°C have high metallization rate (96.2%), reduction degree (99.4%) and compressive strength (960N/pellet). In all tests, self-fluxed pellets display normal swelling (RSI<l5%) behavior which reveals that self-fluxed pellets are suitable for COREX process. Increasing reduction temperature and mole fraction ofH2 in reducing gas is benefit for pre-reduction of pellets.IntroductionCompared with Blast Furnace, the COREX process has advantages of short flow sheet, using non-coke coal and high-energy utilization. Acidic pellets and lump ores are the chief iron- bearing burden for COREX process which could lead to low melting point substance appearing in per-reduction process. In addition, the acidic hematite pellets tend to swell during the reduction [1-3]. This will result in decreasing compressive strength of pellets, burden cohesion, bad air permeability and poor work status in shaft furnace. Adding carbonate flux could restrain burden bonding to some extent in actual production, but decomposition of carbonate flux increases energy consumption. Worse still, weak reduction potential is unfavorable to iron material reduction [ 4, 5]."

Jan 1, 2013

By Wan Pu

Chrysotile asbestos samples from different mines have been studied by SEM and TEM, including high resolution electron microscopy, to find reasons for differences in physical properties of different types of asbestos fibres. The results show that the inner diameters of fibre tubes and the lattice images of fibres are different for soft and hard asbestos fibres. These differences are related to temperatures and geochemical conditions during the growth of chrysotile asbestos.

Jan 1, 1989

By R. Rajiv Srivastava

Brine leaching of a TSL processed zinc-plant residue (ZPR), containing 83.3% anglesite, has been investigated for lead recovery. A prior treatment of ZPR in acid solution did not show any significant effect of acid concentration in zinc dissolution. The study reveals that the solubility limits of PbCl2 is as an important factor with respect to the brine concentration and pulp density in lixiviant. The dissociated sulfate ions hinder the formation of PbCl2 on prolong leaching (above 60 min), while exhibiting the reverse solubility of lead as PbSO4. A 3-step leaching process could yield >92% leaching efficiency when the parameters were maintained as: 10% pulp density in a 250 g/L NaCl solution, 80 °C temperature, and 60 min time. This leaves the insoluble ferrite, sulfides and oxy-sulfates of zinc and lead in the final residue as revealed by the XRD characterization.

By R. Padilla

Enargite (Cu3AsS4) occurs normally associated with copper sulfides, mainly chalcopyrite. When the enargite content in chalcopyrite concentrates is high, direct smelting of the concentrate presents problems related to environmental pollution and contamination of the final metallic copper. Leaching processes are viable alternatives to treat copper concentrates with high content of enargite. Consequently, in this paper, the pressure leaching of enargite in sulfuric acid-oxygen system is discussed. The leaching rate was studied in the range 160 to 220 °C and partial pressures of oxygen of 74 to 200 psi. The enargite dissolution increased substantially with temperature increase. Complete dissolution of enargite was obtained at 220°C, and 100 psi of oxygen pressure in 90 min. The shrinking core model controlled by surface reaction was used to analyze the kinetics of enargite dissolution. Activation energy of 70 kJ/mol was obtained for the temperature range 160 to 220 oC.

Jan 1, 2008

By C. Segawa

SMM operates an original slime treatment process for recovering precious metals and other metals (Te,Se,Sb,Bi)from the copper and the lead anode tankhouse slimes. In recent years, the amount of slimes has increased and the pyrometallurgical processing units capacity became the bottleneck of the entire plants. For the expansion of the plant, new pyrometallurgical facilities, incorporating a BBOC, was commissioned in 1992 and has now been successfully operated. In addition, unit operations were optimized to increase recovery and reduce operating cost .. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1996

By Carla Lupi, Mauro Pasquali

"Photographic technology is based on light sensitivity of silver halides that, because of silver properties, are capable of forming photographic images. Photographic laboratories and hospital departments because of digital photographic systems less use this technology today. Nevertheless recovery of silver is still advantageous because environmental problems related to Ag ions danger to biological system. Many processes have been studied to treat silver containing photographic bath: cementation, chemical precipitation and electrowinning. In this work, after preliminary voltammetric tests, a batch electrometallurgical process has been studied to completely deplete the silver containing photographic fixing baths. The effect, of silver concentration in the electrolyte, varying over the range 0,2-1 g/L, bath stirring and current density ranging from 10 to 500 A/m2 on process yield and deposit quality, has been investigated. Introduction Photographic wastes, electronic scrap and spent catalysts constitute the main sources of materials for silver recycling. Among those silver secondary sources, the photographic discharged material could be still important and useful, even if photographic laboratories and hospital departments, because of digital photographic systems, less use photographic technology. Several processes have been developped in order to recover silver used in the field of photography from both photographic solutions and scrap film paper[1-5]. Fixing solutions are very complex baths but, because of silver position in the electromotive series, electrolysis could represent an advantageous method for silver recovery. Electrolysis produces high purity silver without generating new pollutants, while the fixer can be reused: obviously it is necessary to purge off a portion of this solution in order to avoid the excessive build up of other deleterious compounds into solution. A tested recovery method was constituted by the dissolution of silver from X-ray films with concentrated nitric acid. Internal electrolysis and external electrolysis methods were carried out using a steel electrode as cathode and a copper electrode as anode [6]. Silver recovery from photographic chemical solutions has been also performed in a special cell [7]: the solution is supplied to the bottom of a non-agitated cell having a vertically elongated form and including a central anode enclosed by a cathode. An other study discloses the use of an electrolytic cell comprising at least one anodic compartment and one cathodic compartment: the solution is treated in the cathodic compartment and then recycled in the anodic one [8]. A more recent work proposes the use of zirconium cathode for the recovery of silver from photographic fixing solution [9]: studies carried out by cyclic voltammetry showed that about 98% of total Ag can be recovered with an electrical efficiency close to 92%."

Jan 1, 2008

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By K:-I. Rhee

The recovery of tellurium from Te-cement obtained during the processing of copper anode slimes was carried out by a series of hydrometallurgical processes, i.e. leaching Te-cement in NaOH solution, precipitation of impurites with the addition of Na2S followed by direct electrowinning of tellurium in NaOH solution. The optimum conditions for each process were determined and discussed in terms of various parameters associated with each step to maximize the recovery and purity of tellurium. The final purity of tellurium from electrowinning in alkaline solution was found to be more than 99.9 %.

Jan 1, 1997

By Susana Caballero, Lourdes Yurramendi

Air Pollution Control (APC) ashes from Municipal Solid Waste Incineration (MSWI) plants need to be treated prior to landfilling due mainly to their heavy metals content. This research evaluates the capacity of the APC residues to sequester carbon dioxide, while the ash becomes stabilized for storage. It has the benefit of using two wastes, with no addition of any raw material. APC samples from different MSWI plants were treated by gas/solid accelerated carbonation at different temperatures and carbon dioxide concentrations to evaluate the residue behaviour to the process. The extent of carbonation was evaluated by means of weight gain upon carbonation and by the measurement of the final carbonate content. The APC residues were analyzed before and after the treatment in order to know their composition and their leaching behaviour according to the criteria for the acceptance of wastes at landfills established by the European Council Decision 2003/33/EC.

Jan 1, 2008

By Jogre A. S Tenório

he aim of the present investigation was to investigate technological features of the Fe-NbC dissolution in liquid Fe-C alloys. Fe-NbC is a Ferro-niobium alloy with 7%C, has a particle size smaller than 150 pm and its micro constituents are polygonal niobium carbides and an iron matrix. The obtained dissolution time was less than one-minute and the yields were in the range of 80-90% at 1873 K. In the Fe-NbC dissolution process, the dissolution occurs at first, and as a consequence the niobium carbides become free to dissolve. These carbides will dissolve until the melt reaches a saturation point. The non-dissolved carbides remain trapped in the liquid or will form a dross. The addition yields decreases when the niobium concentration reaches this limit value, that depends on the carbon concentration. These define a saturation curve.

Jan 1, 1994

By M. del C. Ruiz

The extraction of Nb and Ta from a columbo-tantalite of San Luis, Argentina, is being studied by using a pressure reactor and HF as leaching agent. The reagents and products have been characterized by several techniques such as scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), X-ray fluorescence (XRF), X-ray difracction (XRD), surface area (BET) and size particle analysis. Experimental results have shown that the extraction of niobium and tantalum increases with increasing temperature, reaction time and acid concentration. For particle size between +80 and -355 mesh no significant changes are detected. It is also slightly affected by the stimng speed. XRD analysis of the residues did not show formation of new crystalline structures.

Jan 1, 1999

By Neusa Alonso-Falleiros, Aristeu Braz da Veiga, Marcelo B. Mourão, Adriano Pescarmona, Antonio Alberto Froes Schettino, Cyro Takano, Carlos A. S. Giraldo

"The Caron process of nickel extraction from lateritic ores produces a fair amount of an inert residue, the so-called “black sludge”, that is disposed in a dam according to the required environmental regulations. On the other hand, it represents an opportunity to resource recovery. This work presents the characterization of the residue, discusses some possible ways to recover the valuables, and presents experimental results of pyrometallurgical runs aimed at recover nickel as an iron-nickel alloy. It has been shown that the residue contains large amounts of silicon, iron, aluminum and magnesium, in the form of oxides and silicates, and small quantities of nickel, cooper and cobalt, besides several other elements. It has also been shown that gravimetric or magnetic concentration methods do not present promising results. On the other hand, it is possible to obtain iron-nickel alloys by high-temperature carbothermic reduction of the “black sludge”.IntroductionThe Caron process consists of a combined pyro-hydrometallurgical process to extract nickel from high iron limonitic lateritic ores, recovering also the cobalt present in the ore. The main steps are the reduction roasting of the ore, aiming at a selective reduction of nickel and cobalt to the metallic state, avoiding as much as possible iron reduction, followed by leaching with ammonium carbonate solution and the recovery of metal from the pregnant liquor [1,2]. As a result, significant amount of tailings are generated, that are disposed in appropriate dams. This residue, called “black sludge”, contains significant proportion of silica and iron, and also small amounts of nickel, cobalt, cooper and some other elements. Due to diminishing deposits of nickel ore, high metal prices and a significant amount of “black sludge “ available after several years of operation of the plant, Votorantim Metais, who operates a facility in Brazil that uses the Caron process, decided to explore the possibility of recover nickel from the residue. This paper presents the characterization of the residue, and the results of experimental work aiming recovery of nickel from it."

Jan 1, 2008

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By Chen-Ming Kuo, Esher Hsu

"The importers and manufacturers who import or produce products with packaging containers are charged a recycling fee in Taiwan. The amount of waste packaging containers used for calculating the recycling charge is based upon the amount declared by importers and manufacturers which might be underestimated. This study aims to estimate the amount of waste packaging containers generated by households in Taiwan and also explores its distribution. The sampling survey and ratio estimation are conducted for estimating the recycled amount; while the refuse sampling method for municipal solid waste composition is employed to estimate the un-recycled waste packaging containers. The estimated total amount of waste packaging containers in 2011 generated by households in Taiwan is 696,511 m.t., of which, 79.49% of the waste packaging containers were recycled and 20.51 % were landfilled or incinerated. This study shows that the amount of waste packaging containers declared by importers and producers is underestimated around 20%.IntroductionWaste packaging containers including iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs are officially announced to be recycled in Taiwan. In order to create the economic incentive for raising recycling performance, associated manufacturers and importers are charged a recycling fee to subsidize recyclers. The amount of packaging containers declared by importers and manufacturers is used for calculating the recycling charge and recycling rate. The importers and manufacturers might underreport their producing (importing) amount to pay less recycling fees. Therefore, the estimated waste packaging containers based upon the amount declared by importers and manufacturers is usually underestimated. Related previous studies about waste packaging containers recycling in Taiwan are done by Hsu and co-workers [1-4]. Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values. Hsu and Liu [5] provided a cost analysis of recycling for waste packaging containers in Taiwan. Bor, Chien, and Hsu [2] presented a market-incentive recycling system for waste packaging containers in Taiwan. Hsu and Kuo [4] provided an amending mechanism for product charge and recycling subsidy in response to the social economic changes for waste packaging containers recycling. Lee and Hsu [ 6, 7] explored the distribution, fee rates, and collection rate of waste containers. This study aims to estimate the amount of waste packaging containers generated by households in Taiwan and also explore its distribution."

Jan 1, 2014