Search Documents

By Toshihide Takenaka

The management of radioactivated stainless steel from a terminated nuclear reactor will become an important subject in the near future. The separation of the elements in stainless steel should be effective to reduce the management labor. In this study, the separation of the elements in stainless steel by an electrorefining tcchnique was investigated in an aqueous solution. The electrochemical reactions of the elements in stainless steel werc studied by voltammetry and potentio-static electrolysis was carried out. A stainless steel anode was dissolved electro-chcmically with good anodic current etliciency in a chloride solution. The residue, where Ni was concentrated, was found on the anode after electrolysis. The electrodeposit in a stainless steel cathode consisted mainly of Fe and Cr and the Ni content in it was less than 0.5wt% under suitable condition. It is concluded that an electrorefining technique is effective for the separation of the elements in stainless steel.

Jan 1, 2003

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By Z. Sadowski

The influence of organic acids simple salts and A. niger saccharose and molasses worts on sodium oleate adsorption on the salt-type mineral surfaces has been studied. It was found that salts of organic acids had an effect on the sodium oleate adsorption on barite calcite and magnesite. The collector adsorption on the barite and calcite surfaces decreased under the influence of investigated worts. Experimental data suggest that the biomodification of salt-type mineral surfaces can be used for the selective separation of these minerals.

Jan 1, 1991

By Paponetti B. . A.

Gold is usually recovered by cyanidation, thiourea leaching and amalgamation, however the efficiency of these technologies, in the case of refractory ores, is low ever when fuie grinding is practised. For example, .if the gold particles are included in sulphide minerals, the leachant cannot reach them, so they are often lost in the tailings. Hence .it is first necessary to break the sulphide crystals by preliminary treatment such as roasting, nitric .acid oxidation, pressure leaching and bacterial oxidation and then apply a conventional extractive technique for satisfactory gold recovery. This paper describes the effect of biological pre-treatment with Thiobacillus ferrooxidans) on the? extraction ? and? recovery of gold by conventional cyanidate. leaching from; a refractory arsenopyrite ore from Golcuck (Turkey).

Jan 1, 1991

By Zhang Yongzhu

The metallogeneticy and mineralogy of three types of Chinese refractory gold deposits (Au-As; Au-As-MeS; Au-As-C) which are somewhat different from those abroad are discussed. The modes of occurrence, the distribution of grain size, and the morphological features of gold in minerals and their influences on gold recovery by direct cyanidation are also discussed. According to the mineralogy of gold and minerals, bacterial leaching, pressure leaching and roasting technology are suitable for the pretreatment of arsenopyrite-Au, pyrite-Au and carbonaceous-clay-Au refractory gold ores prior to cyanidation, respectively. The most important sulfide pyrite bearing much gold is difficult to be oxidized, its crystalline structure, conduct-types , and minor elements in different mineralizing stages are also discussed. The pyrite aggregates in different deposits are very complicated and much different. Gold grade of arsenopyrite is much higher than that of pyrite for some deposits which have a high correlation coefficient of Au vs As.

Jan 1, 1992

By S. C. Sharma, M. Krishna, N. Sanmukha

"The oxidation behavior of an aluminium composite with 0, 2, 4, and 6% by weight of hematite at 200 to 500 °C has been investigated. Within the experimental temperature ranges a parabolic weight gain was observed. The, weight gain as a function of oxidation time becomes linear after an initial period on oxidation formation, an oxide scale was found whose morphology depends on temperature, cooling rate and sub-scale formation at the interface between the matrix and reinforcement. The presence of hematite particulate reinforcement has very little effect on the oxidation behavior. The interface oxidization rate was found to be higher than that of other regions. The, oxidation products were either metallic oxides or ceramic oxides. The exposure time of specimens to oxidation was 1000 minutes at various temperatures. In the present work key principles of alloy oxidation were discussed. Also the paper emphasizes various reactions taking ' place and the activation energies involved in the oxidation reactions.IntroductionMetal matrix composites (MMCs) reinforced with ceramic particulate, whiskers, or fibers have received increasing attention due to their potentially high fracture toughness and strength 1-5. Particle reinforced Aluminium MMCs find potential application in several thermal environment, especially in the automobile engine parts, space applications, such as drive shafts, cylinders, pistons, and brake rotors6.With the exception of gold, no metal or alloy is stable at room temperature, they tend to form their respective oxides. Most of the metals in the solid or liquid state are morphologically unstable when exposed to air at higher temperatures. An investigation relating to the temperature profiles of the piston area in a diesel engine has shown that the temperature can reach as high as 500¬800 K in certain regions of the piston. As the piston and cylinder areas are exposed to high temperature environment, the MMCs should have sufficient stability on both mechanical and chemical strength (oxidation). Oxidation occurs at grain boundaries in alloys and at the interface of the particulate and matrix in MMCs, which usually enhances intergranular fracture, resulting in premature failure and severe brittleness 8-10. Therefore for high-temperature applications, it is essential to have a thorough understanding of the oxidation behavior of aluminium MMCs."

Jan 1, 2000

By Byung-Su Kim

The reaction between calcium sulfate and hydrogen is of interest both as a means of regenerating calcium sulfide as a reductant of sulhr dioxide to elemental sulhr and for producing elemental sulhr from gypsum. This reaction was investigated using a thermogravimetric analysis technique in the absence and presence of nickel catalyst. The reaction temperature was varied between 973 and 1153 K, while the hydrogen partial pressures of 12.9 - 86.1 kPa were utilized. At 1073 K and a hydrogen partial pressure of 86.1 kPa, 60 % of the original calcium sulfate in the absence, and 95 % in the presence, of the nickel catalyst was converted to calcium sulfide in one hour.

Jan 1, 1999

By José Roberto de Oliveira

Based on literature review one can see that the main objectives of MnO reduction is the comprehension of slag interactions and reactions with other elements beyond carbon. That&apos;s because it is worthwhile to study pure MnO reduction, where there will be not oxides interaction and just carbon will be the reduction agent. By a thermodynamic analysis we know that Si can react with MnO, then it&apos;s important to study this influence, so as Mn content. Our work aims to develop kinetics parameters for the MnO reduction, varying Mn and Si contents in bath. This has been given by pressure measure of CO in a Fe-C bath. The CO is generated by the oxide reduction with carbon. It has been proved that: - Mn content decreases the MnO reduction; - the MnO reduction is mainly influenced by Si content in a bath containing Iron, Carbon and Manganese so as Silicium

Jan 1, 1997

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non-ferrous metallurgical industry is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to ta,ke place at &apos;high temperatures and are now rapidly becoming accepted In many industries. This paper reviews experiences with a proprietary low density ceramic filter element. CerafH. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By E. C. L. Cardoso

Hydrocarbon polymers, as PP, made from cheap petrochemical feedstock are important in many branches of industry. However, they have an undesirable influence on the environment and cause problems due to waste deposition and utilization. Polymeric materials composites account for an estimated from 20 to 30% of total volume of solid waste disposed. Thus, there is a tendency to substitute such polymers by those ones that undergo biodegradable processes. Polypropylene (PP) is a commodity, with high melting point, high chemical resistance, low density, with a balance between physical and mechanical properties and easy processing at low cost. Nevertheless, PP shows limitations for some special applications in automotive industry and civil construction. In order to minimize this deficiency, related to rheological behavior of polymer melt, especially referring to viscosity in processing temperature, a 50% mixture with HMSPP (High melt Strength Polypropylene) was used. PP/HMSPP was blended with 10, 15, 30 and 50% of natural (sugarcane bagasse) and synthetic polymers (PHB and PLA) aiming to partially biodegradable materials. The admixtures were subjected to gamma-irradiation at 50, 100, 150 and 200 kGy and then further assessed by mechanical tests in order to evaluate their degradability.

Jan 1, 2015

By Marcio Toshio Tanaka, Marcelo Breda Mourao, Cyro Takano, Cesar Yuji Narita

"The concerns in questions related to the environmental impact in the steelmaking industries caused mainly on the gas emissions such as the dioxide carbon are due to its raw material such as the coal, a fossil and non renewable resource. The purpose of this paper is to replace from 10% to 50% of the coal used in cokemaking by mixing it with a renewable source (wood charcoal). The powder (- 325 mesh) from both raw materials (coal and wood charcoal) were mixed in order to obtain a briquette that was then heat treated at 1100°C to obtain the biocoke. Results of usual analysis (coke reactivity index, coke strength after reaction and cold crushing strength test) were employed to compare to regular coke briquettes. It was found that biocoke with different amounts of wood charcoal present features enabling it to be used in some ore reductionprocesses.1. IntroductionThe iron and steelmaking industry is a heavy emitter of carbon dioxide; according to the World Steel Association, 6.5% of global emissions of this greenhouse gas is due to the production of ferrous materials [ 1]. This is due to the fact that the fuel and reductant employed in the blast furnace is metallurgical coke, obtained from fossil coal. There are some projects aiming to reduce or even eliminate the emission of fossil GHG in the iron and steelmaking process [2]. Most of them propose the capture and storage of the gas (CCS) [3], a technology not yet proven. Other studies point out that the coke consumption in the blast furnace could be reduced by using high reactivity coke; this could lead to lower temperatures in the thermal reserve zone of the blast furnace and consequently less fuel rate in the furnace.The use of biomass in the iron ore reduction process is known as an environmentally accepted solution, as biomass does not release already fossilized carbon."

Jan 1, 2013

By M. Misra

The prediction and assessment of the reactivity of acid mine tailings has been a subject of numerous studies. The conventional approaches such as sulfur content, pH, net acid generating capacity and conductivity are used for assessing reactivity of the tailings. In this paper a new non-invasive Impedance Spectroscopy (IS) technique is used for the determination of reactivity and acid mine potential of tailings. This technique is also used to establish the long term stability and leaching propensity of the tailings agglomerated with alkaline binders.

Jan 1, 1994

By Bing Hu, Zhu-Cheng Huang, Guang-Bin Xia, Hu Peng, Hua Wang

"The temperature rising characteristics and reaction of the reduction of iron oxide pellets with anthracite fines were studied using a MW-L0316V microwave oven and Leica-DM-RXP polarizing microscope. The results show that iron oxide pellets and anthracite fines have good microwave absorbing properties, and high temperature and reducing atmosphere in a relatively short time for reduction of iron oxide pellets can be achieved. The reduction reaction, which follows the unreacted core model, is rapid and the metallization increases from 13.41% to 56.57% as the reduction end point temperature increases from 850oC to 950oC. The iron is formed, fine grain crystals of iron are transferred and the contraction of metal phase occurs firstly at the surface of pellets, which hinders the reduction reaction at the center of pellets. The rate of reduction reaction increases slowly as the reduction end point temperature increases from 950oC to 1050oC.IntroductionIron ore direct reduction can be divided into gas-based reduction and coal-based reduction. Owing to the effect of the resource and the related economic benefits [1, 2, 3, and 4], the development of gas-based direct reduction technology is restricted, but the development of coal-based direct reduction supported by the relevant industrial policy has very good prospects for application.As a source of clean energy, in China microwaves have been applied in many fields [5, 6, and 7]. Chen Jin studied the reduction of carbon pellets under microwaves, and has made some progress on reduction kinetics and reaction mechanisms. Other countries also have related research in this field [8 - 15], for example, Kotaro Ishizaki and Kazuhiro Nagata have done research on the reduction reaction of carbon magnetite heated by microwaves. The research shows that Fe3O4 is deoxidized to FeO at about 800oC, and FeO is deoxidized to Fe at 1000oC-1025oC. Due to the very good heat absorbing properties of iron oxide pellets and anthracite fines, the selective and rapid heating of microwaves can rapidly raise the temperature of pellets and anthracite, and the iron oxide pellets can be rapidly reduced. In order to provide enough theoretical basis for direct reduction by microwave heating, this paper studies the temperature rising characteristics, behavior of the reduction reaction and the changes of the iron oxide pellets and anthracite in the microwave field."

Jan 1, 2011

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Dao Su, Ganghua Fu, Xuling Chen, Yufeng Guo, Min Gan, Tao Jiang, Xiaohui Fan

"The sinter quantity and quality of limonite in the magnetite and hematite sintering models were studied and compared. For the sintering of magnetite, the results showed that the increase of limonite improved the permeability of sinter mixture, increased the sinter quantity and quality. The sinter strength and productivity were decreased when the proportion of limonite exceeded 50%. The appropriate proportion of limonite was 40%-50%. For the sintering of hematite, the sinter quantity and quality were first maintained at the same level thereafter declined, more obviously when the proportion of limonite exceeded 40%. The amount of calcium ferrite increased whose shape changed from acicular to leaflike and block gradually with the proportion of limonite increased from 0% to 80%.IntroductionWith the fierce competition of domestic and overseas iron markets in the twenty-first century, cheap ores such as limonite are used to be sintering raw materials to cut the costs of sinter and pig iron for steel making, and boosts the competitiveness of steel companies [1, 2]. In addition, as the reserve volume of hematite of high grade is reducing year by year, the usage amount of limonite in sintering are expanding in major domestic and international sintering plant [3, 4]. Sintering can be divided into two types, majoring in concentrates and fine ores, according to the different types of raw materials. The sintering characteristics of limonite in the two types above have been studied and compared in this paper, which makes a significant sense for the research of limonite sintering properties and guidance of ore proportioning in sintering plants."

Jan 1, 2012

By William Petruk

An investigation was conducted to determine types of particles that tend to be recovered in concentrates by mineral beneficiation. It was found that, in concentrates of the same grade the proportion of desired mineral occurring as apparently liberated grains varies widely. In contrast the proportion is nearly constant when the grains considered are apparently liberated grains plus unliberated grains in particles composed largely of the desired mineral. It was also found that the types of particles which tend to be recovered in concentrates are dependent upon the concentrate grade. Hence it is much more important to determine the characteristics of recoverable particles and to measure the percentage of mineral that occurs in recoverable particles. than to measure the percentage of totally liberated mineral. A relationship between concentrate grade and type of particle that tends to be recovered in concentrates was established.

Jan 1, 1989

By Hans Jürgen Maier, Gregory Gerstein, Florian Nürnberger

Microstructural analysis to support the development of material models provides valuable information to design complex forming operations. Damage models such as e.g. by Gurson consider spherical voids only. However, investigations of bcc steels by scanning electron microscopy reveal that voids exhibit an ellipsoidal shape with progressing deformation. The material’s weakening in the Gurson model is taken into account by the void volume fraction. Therefore, a three-dimensional characterization of the void shape offers important data for modelling. Thus, information on the anisotropy of the process of void evolution and accordingly, about the anisotropy of the deformation process is provided. Application of the information regarding the void shape anisotropy within the Gurson model is discussed.

Jan 1, 2016

By Sun Ying, Zhang Jing, Li Qiu-ju, Wang Yan-ze

Copper smelter slag was leached using sulphuric acid solutions under atmospheric conditions. Base on the composition and phase of copper slag, the effect of the concentration of sulfuric acid and leaching temperature to the leaching growth rate of Fe, Cu, Co and Ni in the copper slag were investigated in this paper. Simultaneously, the influence of sulfuric acid concentration, leaching time, leaching temperature and the amount of sulfuric acid (solid-liquid ratio) to the leaching rate of these metal elements were researched. Experimental results showed that: with the increasing temperature, the dissolution rates of the metals elements increased first and then decreased. Due to the influence of silica gel which was obtained in beginning of leaching, the higher the concentration of sulfuric acid is not conducive to dissolution of the valuable metal elements. The dissolution degree of Fe, Cu, Co and Ni were 92.83% 96.76% 93.62% and 63.41% respectively.

Jan 1, 2016