Search Documents

By Fanke Meng

Electrolyzing oxides of titanium, aluminum and niobium could prepare high-Nb bearing TiAl alloy (Ti-45Al-9Nb) at 1500°C. The chosen electrolysis voltage is 3.5V, which is lower than reducing voltage (~4.7V) of electrolyte CaF2, but higher than that of titanium, aluminum and niobium oxides. The investigation shows that compared with traditional methods, this method for preparing high-Nb bearing TiAl alloy is of many advantages such as few steps, friendly environment, low energy consumption, low cost and high current efficiency.

Jan 1, 2009

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades. EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized.

Jan 1, 2003

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

A novel, low-pressure adaptation of Praxair?s coherent jet technology utilizing CoJet lances was developed for application at Inco&apos;s Copper Cliff Smelter where oxygen is available in large tonnage quantities but only at relatively low supply pressures (< 193 kPa header pressure). The project objectives were to evaluate the effect of coherent jet technology on controlling oxygen lance accretion (?horn?) formation and to increase oxygen efficiency in the Inco Oxygen Top-Blowing Nitrogen Bottom Stirring (TBBS) MK Reactor used for converting nickel- contaminated chalcocite to semi-blister copper. This paper describes the development and subsequent implementation and testing of two CoJet lances in this application.

Jan 1, 2005

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By Y. Moriya, Y. Sadayoshi, Y. Nonogaki, Y. Takeda

"Preparation and growth processes of CaF2 on Si(111) and of . InxGa1-x,As islands on CaF2 by molecular beam epitaxy (MBE) are described. It was found that first of all the Si(111) surface treatment process to obtain the 7x7 reconstructed structure was necessary to ensure the cleanness of the surface and to grow a flat and high quality CaF2 on it. Growth of InxGa11-x,As islands on CaF2 was tried by droplet heteroepitaxy using the same MBE reactor. In,GaxGa1-xAs islands were successfully grown epitaxially, and the size and density of the islands dependent on the In composition were investigated.IntroductionThough semiconductor/semiconductor heterostructures are widely used for many device applications, small band off-sets of the conduction bands and the valence bands restrict the utilization of the intra-subband transitions to far-infrared regions. With InAs as the quantum well and fluorides as the barrier layers, we can design three-electronic-level systems in the infrared region, which is the low loss transmission window of the silica optical fibers. To realize those structures, we have grown InxGa1-xAs islands on CaF2 thin films that were epitaxially formed on Si(111) substrates by molecular beam epitaxy. By the droplet heteroepitaxy that we invented, the InxGa1-xAs islands with height of -10 nm have been obtained successfully. Optimum processing to obtain atomically smooth surfaces of Si and CaF2 and high quality InxGa1-xAs islands is reported.ExperimentsMBEMachineCaF2 was grown on Si(111) and InxGa1-xAs islands were grown on CaF2 successively by MBE. The MBE machine consisted of a growth (or reactor) chamber and a loading chamber. The reactor chamber was equipped with Ga, In, As and Er metal source cells and CaF2 and BaF2 source cells. Cell materials were P-BN for Ga, In and As metals, and were graphite for CaF 2, BaF 2 and Er to avoid reaction with BN cells. The electron gun and screen were attached to the reactor to observe the RHEED pattern during the substrate surface treatment and the growth of CaF2 and InxGa1-xAs islands. The substrate manipulator was designed to heat up the Si substrate up to 1,200°C for the surface cleaning. The QMS was also equipped to analyze the residual gas species in the reactor chamber. The base pressure of the reactor chamber was 2-5x10-11 Torr, being pumped by ion pump and the liquid nitrogen shroud"

Jan 1, 2000

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifying its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multicomponent slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today&apos;s reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author&apos;s group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifYing its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multi component slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today&apos;s reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author&apos;s group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

By J. A. Holmes

Due to varying and complex mineralogy, the flotation tailings from the Chingola Concentrator have, for some years, contained upwards of 0.4% acid soluble copper. In 1968, an investigation was initiated, to determine a method for recovering this acid soluble copper. This initial investigation concluded with a recommendation to install a leach-solvent extraction-electrowinning plant at Chingola, to treat up to 900 000 tonnes of material per month, for an additional copper production of some 4 500 tonnes per month. The process consists basically of six stages :- Materials reclamation handling and preparation, acid leaching in air agitated pachucas, solid-liquid separation by countercurrent washing in thickeners, solution concentration and purification by solvent extraction, copper recovery by electrowinning, and residue neutralisation and disposal. This paper describes the development of the main parameters for design of each of the six sections, and gives details of the final plant design. Problems encountered in commissioning and initial operations are commented on, particularly insofar as they indicated any errors or misjudgements in the design. The choice of materials of construction is commented on in some detail.

Jan 1, 1976

By Joner Oliveira Alves

The aim of this work was to study the use of steelmaking slag as raw material to the production of rock wool and glass wool. Firstly, the chemical composition of the slag was analyzed. These results were used to infer the amount of additives to assemble the charge for the experiments. A laboratory-scale electric furnace was used to melt the mixtures used as charge. The melt material were turned into a water filled recipient, this process was performed in order to impose a fast freezing that is a characteristic of mineral wool production. Finally, with the rest of the melt material it was performed the Herty Viscosity Test. Samples of the produced material were characterized by different analyses. The results found in this research may lead to a technological innovation, because they indicate that the use of steelmaking slag to produce rock wool and glass wool is possible.

Jan 1, 2009

By R. Schaller, Ch. Karcher, A. Thess

"Electron beam evaporation of liquid metals is an innovative technology increasingly used in industry to produce very thin coatings of high purity. In this process the surface of a metal ingot, placed in a water-cooled copper crucible, is heated by bombarding it with a high-energy electron beam gun. The material melts, forming a free surface and eventually starting to evaporate. The rising vapor cloud condensates as a thin film on a moving substrate. The strong energy input at the free surface gives rise to vigorous thermos capillary and buoyancy driven convective motion within the melt, leading to unwelcome heat losses. This paper aims to show how these losses can be reduced by optimizing the geometry of the crucible and by using external magnetic fields. We present both experimental and numerical results.IntroductionElectron beam evaporation of liquid metals [l] is an innovative PVD-technology which is excellently suited for the industrial production of high-quality coatings. In this vacuum process a high-energy electron beam heats up the surface of a metal ingot. The ingot melts and forms a free surface. A schematic view of the arrangement is shown in Figure 1. When the temperature of the free surface exceeds the actual (pressure-dependent) saturation temperature of the ambient gas, the liquid starts to vaporize. The rising vapor cloud finally condensates on a moving substrate located at some distance above. To guarantee a superior quality of the coating the melt is typically confined in a water-cooled copper crucible. The intensive cooling is necessary to avoid chemical reactions between the melt and the crucible walls, that is, crucible materials and their reaction products are practically excluded from evaporation."

Jan 1, 1999

By Robert Hanson, Mayur K. Patel

"Pneumatic conveying pipelines are used throughout a variety of industries, from food processing/packing to power generation plants, as an efficient means of transporting materials between storage and processing points. In general, different phases of pneumatic conveying exist when material is conveyed from point A to point B in a pipeline. This depends on the operating pressure and the material conveyed. Lean phase conveying exists when pipelines are operated at high airflow rates, relatively low pressures, inducing sufficient turbulence for particles to become entrained in the air stream. Thus, particles are conveyed along the pipelines at velocities in the range of IS-2Sm/s. Generally, the initial capital costs for lean phase system is low, however the running costs are high. The opposite is true for dense phase, high-pressure systems. In considering either conveying system, it is important that the rate of erosion of the pipeline be considered when designing such a system, since it is the rate of erosion that dictates the lifetime of components. In general, the high level of erosion occurs for lean phase flows, where high impact velocity contribute substantially to the rate of erosion as well as other processes such as particle breaking, if the particles are friable. This would lead to poor quality of material, not normally desirable. On a positive note, the process of erosion is used in other applications, which benefits from this process, e.g. abrasive guns.The failure, by puncture, of pneumatic conveyor bends in industry causes several major problems. Two of these are: (a) escape of the conveyed product causing health and dust hazard and (b) repairing and cleaning up after punctures necessitates shutting down conveyors, which will affect the operation ofthe plant, thus reducing profitability.The paper reports on modelling strategy used in the development of a modelling framework and the initial validation phases of the models incorporated within. The modelling framework encompasses Computational Fluid Dynamics (CFD) related engineering tools, based on Eulerian (gas) and Lagrangian (particle) approaches, to represent the two distinct conveyed phases, to represent the erosion process which is used to ascertain the lifetime of conveyor bends."

Jan 1, 2001