Search Documents

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By Zizheng Zhou

The separation of cobalt from other base metals can be achieved using diffusion dialysis in a two-compartment reactor separated by an anion exchange membrane. In this work, a Neosepta AFX membrane was used to study the separation of various metals in an acid-chloride solution. The separation of one metal from another was investigated on the basis of the various chloro-complex stabilities. The metals investigated included cobalt, nickel, copper(II), iron(III), aluminum, zinc and cadmium. The impact of several critical experimental conditions, including the initial metal and chloride concentration in the feed solution and their initial concentration in the receiving solution, on the separation factor and the metal transfer rate is reported in this work. Effective separation of different metal pairs was achieved under the experimental conditions.

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. n this work, the potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (OW). Seven taxa are of Alyssum genus and one of BornmueIIera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mg/kg or 2.5%) and Alyssum markgrafii O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. In this work, thc potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (DW). Seven taxa are of Alyssum genus and one of Bornmuellera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mglkg or 2.5%) and Alyssum markgrafli O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By Daguang Lu

The section of sintering and BF (blast furnace) is very important in iron-making process. In practice, the scheduling is so extensive that three faults unfavorable to continuous product will be easier to happen. This paper introduces the integration Petri Net and GA (genetic algorithm) as suitable tools for simulation and optimization of scheduling to section of sintering- BF under a certain hot iron or-der. The situation of the iron plant Chongqing Iron and Steel Company is researched in approach above mentioned. By analysis, the conclusion is drawn that scheduling with optimized values can maintain continuity of key operations , can satisfy order of hot iron in maximal degree and can keep the best stability of key storages.

Jan 1, 2009

By M. F. El-Demerdash

The activity distribution diagrams for different species in aqueous systems are developed. Computational method may be considered as an extension of the Activity-Term method introduced by the authors to construct EH-pH diagrams. In the Activity-Term method, all activities of different species are evaluated before deciding the most stable one. In the present study, a factor is assumed to allow for the conservation of the element. At any point, the total concentration of all species should contain only the input m moles of the element (elements) considered. This approach is applied to Zn-, 5-, and Zn-S-H2O and activity distribution diagrams are plotted as a function of pH, at different potential levels and at different temperatures.

Jan 1, 1990

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By O. Barbosa F.

The thermochemistry of the systems SCN-H2O, Au-SCN-H2O and Ag-SCN-H2O is discussed. Potential-pH diagrams at 25°C are drawn for each system considering several sets of concentrations of the species involved. The information provided by the potential-pH diagrams is.complemented by distribution curves for each series of gold and silver complexes with thiocyanate. The analysis includes comparisons between the thiocyanate systems and the analogous cyanide systems, pointing out analogies and differences between the leaching of gold and silver with thiocyanate and with cyanide. The possibility of using soluble oxidizing agents such as ferric ions, hydrogen peroxide and Caro's acid is evaluated. The thermodynamic data used in the calculations and the chemical reactions represented in the Pourbaix diagrams are all reported in three Appendices. The overall results indicate the thermodynamic conditions for gold and silver leaching by thiocyanate.

Jan 1, 1989

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By Guo Gongyi

An extraction chromatography by which 99.99 % pure scandium oxide can be prepared from the starting materiel containing about 70% scandium oxide has been developed by taking advantage of some peculiar properties of the complex chemistry and extraction chemistry of scandium. The purification of scandium was performed at room temperature with relatively fast rates in two chromatographic columns. The preliminary separation of scandium from impurities was done by extraction chromatography using tri-butyl phosphate as the stationery phase in the presence of citric acid, and the nearly complete separation in the presence of perchloric acid. The scandium recovery was greater than 90 %.

Jan 1, 1989

By Jonkion M. Font, Ramana G. Reddy

A thermodynamic model for a priori predictions of arsenic and antimony impurity capacity in Ni-Cu mattes and slags was developed based on the Reddy-Blander (RB) capacity model. The As and Sb capacities were calculated a-priori considering the RB capacity model in Ni-Cu mattes and FeO-FeO1.5-MgO-CuO0.5-NiO-SiO2 slag at 1573 K and 0.1 to 1 atm partial pressure of SO2. The results showed an excellent agreement between the model calculated and experimental data of arsenic and antimony capacities between the mattes and slag. The impurity capacity model developed here, can be extended for prediction of impurity capacities in multi-component base metal slags and base metal mattes. Such a priori predictions of impurity capacities can lead to develop or improve the efficiency of impurity removal from the base metal smelting, converting and refining processes.

Jan 1, 2014

By A. Buzaianu, P. Motoiu, G. Popescu, C. A. Popescu, I. Rusu, A. F. Olteanu

"In recent years, the recycling magnesium metallurgy has developed new types of alloys, some of which exhibiting special electrochemical characteristics. Their application has found a fertile field in the energy conversion technologies. The paper introduces some technologic data on the recycling of aeronautical parts and scrap materials generated from the disassembling of magnesium alloy components, attempting to also solve the recycling of magnesium painted parts. The approach is meant to establish a superior quality method for recycling discarded parts or the excess of re-melting material in order to reduce environmental impact and costs. Magnesium-base alloys used as anodic materials are characterized by a high uniformity of the structural properties as well as by superior electrochemical performances, as compared to the ""classically"" used materials: Zn, Pb, etc. In nonconventional applications of magnesium alloys used as sacrificial anodes working in seawater, special alloying elements contribute to improving anodic processes. The influence of these alloying elements on magnesium sacrificial anodes was studied. It was found that the use of recycled materials in anode manufacture could reduce the Mg alloy cost by as much as up to 75% of the cost for virgin material, including the costs for the entire sequence of collection and transportation from a molding factory to a refinery, re-melting and composition adjustment.1. IntroductionMagnesium alloys are valuable materials because they exhibit low density, good forming and machining qualities, particular electrochemical properties and have a high recycling potential. There exists a false idea about the high costs of the use of magnesium alloys, partly justified by the lack of secondary materials suppliers and the insufficient knowhow in the diverse user industries to provide for an efficient substitution of conventional magnesium alloys for multipurpose applications. These circumstances have lately spurred the magnesium industry to develop new alloys and coatings and to improve processing techniques [1]. As a result, magnesium supply has greatly expanded and so have the research and development efforts to achieve complete recycling of Mg alloys.In consumer markets, magnesium is frequently selected because it helps reduce enery consumption. For example, an equal volume part made of magnesium is 23% the weight of a steel part and 64% the weight of an aluminium part."

Jan 1, 2008

By J. W. Perez

A simple exponential model has been developed (Perez and Aplan. Process Mineralogy, VI, 1986) to describe the fractional yield of a given species out of a locked assemblage: Fractional Yield of Species A = a e X/U where 'X' is particle size and 'a' and 'U' are constants. In the present study, the general validity of this model has been further demonstrated. experimentally, for the liberation of coal and pyrite out of various raw coals and beneficiated fractions using a variety of crushing devices. Using data from the literature, the model is also shown to be applicable to the liberation of sulfide minerals out of ores.

Jan 1, 1987

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of873 OK is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composItion formed under roasting of concentrates with particle sizes less than 0.02 J..lm (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CufeSz) each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forehamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By R. K. Mehta

Microorganisms have been increasingly used in applications such as-metal solubillzation, precipitation and recently being used as flocculants. Optimal control and on-line monitoring of these processes occurring in microbial reactors are of extensive interest but often difficult because of the unavailability of a mechanistic model of the process and on-line direct sensors. In this paper a dynamic populatlon balance model of microbial desulfurization will be presented. The influence of certain physical and biological parameters on the leaching rate will be illustrated via computer simulations and an extended continuous-discrete Kalman filter will be Implemented for estimation of unknown states.

Jan 1, 1991

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By D. McConchie

Management of caustic red mud wastes at the QAL bauxite refinery uses an innovative approach . involving neutralising the red mud with seawater; solids settle in a Red Mud Dam and residual water (pH = 8.6) is discharged to a tidal inlet. A survey of 18 trace elements in sediment, water, mangroves and molluscs, and an ecological survey of benthic fauna in the inlet, and at near-pristine control sites, revealed no significant trends that were linked to the discharge, except for the concentration of Al which was slightly elevated within 100m of the outfall. Trace element concentrations in water samples were close to, or below, world average seawater values and oysters collected near the outfall were acceptable for human consumption. The impact of discharges is minimised by a high tidal range, >60% flushing of the inlet in each tidal cycle, and the very high trace element binding capacity of sediment in the dam (> 100meq/ 100g dry mud).

Jan 1, 1996

By . Menad Gaballah I

Three samples of solid wastes generated by the non ferrous metallurgy were characterized. These residues contain up to 42 % of valuable metal compounds ( Cu, Pb and Zn ) and 23 %of toxic compounds t As, Hg, Cd and Se ). These sample were subjected to thermal treatments between 200 DC and 800 °C in controlled oxidizing. reducing and chlorinating atmospheres. Up to 99 % of As, Cd, Hg and Se were eliminated from these industrial wastes. Cu, Pb, and Zn compounds were concentrated in the treatments&apos; residues of these samples. A Global Decontamination Factor&apos; GDF &apos; was defined to measure the efficiency of the elimination of toxic elements and the recovery of valuable elements for a specific sample submitted to a given treatment. It seems that the thermal treatment in a reducing atmosphere was the most efficient in decontaminating these solids and the concentration of valuable elements. a.

Jan 1, 1995

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995