Search Documents

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By M. Potesser

After the primary or secondary lead production the bullion lead is remelted and charged into a vessel with following refining process. The removing of arsenic, antimony and tin takes place by salt slags or oxidizing gases like air or pure oxygen. Due to the increasing lead price, Messer Austria GmbH in cooperation with the institute of Nonferrous Metallurgy at the University of Leoben have developed a new process named OXIPOT for the refining of tin, arsenic and antimony. The OXIPOT process is in principle based on purging technology with a ceramic or steel purging device. This leads to an increased retention time of the refining products due to the deeper bath level and an optimized specific reaction volume concerning the bubble size. This paper describes the process, pilot plant, and thermodynamic calculations for the optimization concerning the selectivity of element removal.

Jan 1, 2008

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By M. Hashimoto

The equilibrium distribution ratios of sulfur between molten copper and CaO-fluxes containing caF2 and caC12 were determined in the range of 1300° to 1400° C under carbon monoxide. The rate of approach to equilibrium is rapid and increases with increasing CaCll concentration. In CaO-CaFl-CaCl2 fluxes, the distribution ratio varies in a complex way with temperature and CaFl concentration. The results are compared with those obtained with the binary fluxes of CaO with BaFZ and MgFl ?

Jan 1, 1983

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Y. Takasaki

For zinc hydrometallurgical extraction, reducing the electric power consumption of the electrowinning process is an important issue for energy savings. At the Zinc & Lead 2000 symposium, the authors suggested that by using the Pb-0.5%Ag-0.6%Ca alloy, the electrolysis energy can be decreased compared to the conventional Pb-0.9%Ag alloy. In this study, the corrosion behaviors of the Pb-Ag-Ca electrode in a sulfuric-acid electrolyte were investigated. Based on the results Or me Pb-0.5%Ag-0.6%Ca anode after 20 days of electrolysis, the bath voltage and the quantity of anode slime decreased compared to the Pb-I%Ag anode. Subsequently, beta-PbO2 on the electrode surface was detected by XRD and its peaks were sharper than the Pb-1 %Ag anode. Moreover, a dense beta-PbO2 layer on the 0.6%Ca a anode surface was observed. Therefore, it was suggested that the dense beta-PbO2 layer on the anode surface is one of the factors that leads to a lower bath voltage and decreasing quantity of anode slime.

Jan 1, 2003

By L. Sh. Tsemekhman

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By B. A. Paponetti

The following report discusses the bioleaching of chalcopyrite of italian origin catalyzed by Thiobacillus ferrooxidans. The developments vcr.ius time of the main .biochemical and chemical reactions involved in the production of soiuble and insoluble species were investigated focusing on the times at which they begin and bow long they last. The precipitates were characterized both in quantity and in quality relating the rate of the process to the precipitates fonnatiom. A material. balance has been made to verify the proposed mechanism.

Jan 1, 1991

By Michael S. Moats, Scott C. Campin, J. Brent Hiskey

"Electrochemical techniques are a valuable means of analyzing the passivation of commercial copper anodes. Electrochemical impedance spectroscopy (EIS) provides information concerning transport and reaction phenomena occurring at an electrode surface. Commercial. copper anodes of varying compositions have been examined using EIS. Experiments were conducted in a flat cell with an electrolyte of 40 gil Cu2 + and 160 gil H2S04 maintained at 65 DC. Impedance spectra were obtained at the potentials characteristic of the open circuit voltage and passive region for each anode. The spectra of the passivating films exhibited a flattened resistive/capacitive loop at middle to high frequencies and an inductive loop at low frequencies. An equivalent· circuit utilizing an inductor-resistor series in parallel with the double layer capacitance and charge transfer resistance was adequate in modeling the impedance data. The influence of anodes impurities on the components of the equivalent circuit is discussed and correlated with a hi-layer passivation model.IntroductionPassivation of copper anodes during industrial electrorefining has received considerable attention in the past few decades. Great strides have been made in understanding the roles of anode impurities [1-25], electrolysis parameters [20,26], and electrolyte chemistries [20,26]. Even so, passivation still occurs even in the most modem of refineries. The exact cause of passivation is not fully understood. It is known that the anode surface becomes covered by a passivating film. This film has been proposed to be CuS04'&5H20, Cu20, or mixed oxides. The localized concentrations of Ft, Cu+, and Cu2+ ions determines which phase is more favorable. The presence of these ions is controlled by the reaction kinetics and diffusion of species through the slimes layer.Reaction kinetics between Cu, Cu +, and Cu2+ are based on the dissolution mechanism of copper. There exists four different models to describe the dissolution of pure copper. The classical model of Mattsson and Bockris [27] involves two single electron transfers with the cuprous-cupric reaction being the rate detennining step. More recently, Wong, Collier, and MacFarlane [28] used ac impedance to elucidate a more complex mechanism involving the affect of pH and anions. Their findings indicate that the formation of cuprous ions in solution, Cu(I)so~ is favored over Cu(1I) ions adsorbed to the electrode surface in the presence of sulfate and as pH increases from pH 1 to pH 5."

Jan 1, 1997

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By H. Y. Sohn, Joshua E. Ramos, Moo Eob Choi

"A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. This technology would drastically lower CO2 emission and reduce energy consumption by nearly 38% of the blast furnace requirements. Experiments were performed using iron oxide concentrate at 1150oC in a bench-scale facility, which was the highest temperature that could be reached in the facility. The reduction extent was determined at residence times of 3.5 - 5.5 seconds in which the reduction extent approached 43% with 0% excess H2 and 95% with 860% excess H2. Separate kinetics measurements showed that the rate is much faster at 1200 - 1400 oC. Experiments were also carried out using syngas (mixtures of H2 + CO). About 90% reduction in 3.5 seconds with 860% excess hydrogen contained in the syngas demonstrated sufficiently fast reduction for a suspension process and the feasibility of usingsyngas instead of pure hydrogen.IntroductionDespite the improvements in the modern blast furnace (BF) process, it suffers from many drawbacks. The process requires the feed in the form of sinters or pellets and high-grade coking coal. Thus, BF iron production is projected to decrease gradually [1]. The main factors for this are the environmental regulations [2] and the high capital investment cost.A large number of new ironmaking technologies have been developed or are under development [3]. Most of these processes, however, are not sufficiently intensive to replace the blast furnace because they cannot be operated at high temperatures due to the sticking and fusion of particles. Therefore, a new technology is under development for producing iron directly from fine concentrates by a gas-solid suspension technology, which would reduce energy consumption by about 38% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry."

Jan 1, 2009

By S. B. Bortnikova

This paper presents the results of an investigation of the gold-silver oxidized ores at the Salair mine. West Siberia. High losses of precious metals during primary ore processing are the result of outdated technology that is not suited to treat the present ore compositions. The main mineralogical forms of gold and silver and their confinement to different grain size fractions have been determined. About 50% of gold in the slime fraction and 60% of the silver in the form of acanthite that are scattered from the secondary minerals are lost to the waste. The results of these investigations have provided the basis for the recommendation of a new technological process to upgrade the current practice of the gold extraction plant and for methods to reprocess the concentrates.

Jan 1, 1995

By Milton Blander

"A review of concepts and theories for predicting thermodynamic solution properties of multicomponent high temperature liquid solutions is reviewed. During the last 50 years the ability to predict such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.INTRODUCTIONA number of solution theories and concepts have been developed which reliably predict the properties of multicomponent solutions from those of the lower order systems (often only the binaries). Because there is available data for a large fraction of the important binaries, the capability for making predictions for many multicomponent systems used in metallurgical separation processes is broad and potentially very useful. At the very least, the theories greatly minimize the data necessary for predicting properties of complex multicomponent solutions of molten salts, silicates and metals. It is the purpose of this paper to discuss the concepts which are demonstrably useful. We will discuss simple forms of the theories to make the concepts clear but we will refer to the publications which contain the more complex equations needed to treat the large majority of systems.A simple framework for understanding what we need to know in order to make technologically useful predictions is based on well known thermodynamic principles. In technologies and sciences where molten salts, slags magmas or molten metals are used or studied, one must often calculate the extent of a chemical reaction (or separation) or of phase changes. To do this, one must first write an equilibrium constant, K, for the reaction in terms of the standard free energy change of the reaction, ?G°."

Jan 1, 1996