Search Documents

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003

By Raymond PoIick

The Demag Electric Slag Cleaning Furnace installed at the Asarco Smelter in Hayden Arizona is one of the few rectangular electric furnaces now operating. The long transition times from charge to tap allow exceptionally clean skims (high recovery); however, the furnace design is complex. Additional Asarco requirements for rapid installation and commissioning further complicated the design. When operating and wear effects accumulated after two years of use, steps were taken to rebuild the furnace with enhanced durability based on the design parameters experience in actual use.

Jan 1, 1993

By Yuan Zeping

The distributions of impurities in the copper melt, the slag and the gas phase in copper flash smelting process were under study in the Guixi smelter, particularly during operating conditions of high oxygen enrichment with production of high grade matte. Several methods for the removal of impurities such as As, Sb and Bi in the copper smelting process were developed and implemented at the Guixi smelter. This paper described the effects of high oxygen enrichment, elevated matte grade, high temperature and high production rate on the distribution of impurities, methods adopted at the smelter for the removal of impurities, and the associated benefits in the utilization of these removal techniques which include the mathematical model for material blending, high thermal intensity operation at the flash furnace, extended converter blowing, and injection of slag modifiers consisting of Na2CO3 and CaO powder mixture to the converters and anode furnaces.

Jan 1, 1999

By Ramasamy Santhanam

"India’s present annual marine fish catch is 2.9 million tonnes and its low value fishes such as sardines, sciaenids, goat fishes and leiognathids amount to 60%. The fish meal obtained from these resources is mainly used presently as an ingredient in live stock and aquaculture feeds. These fishes offer vast scope in the production of pet foods. Pet foods prepared with leiognathid fish meal (60%), maize flour (10%), wheat flour (5%), vitamin and mineral mixture (5%) and water (20%) and experimented with 50 cats and 50 dogs were found to be ideal. Depending on protein level, feeds are being formulated for experimenting with more number of pet animals. Training programmes are also planned for unemployed people to popularize pet foods for commercial purposes.IntroductionIndia’s present annual marine fish catch is 2.9 million tonnes and low-value fishes sucha s sardines (Sardinella albella, s. gibbosa, S. fimbriata and S. melanura); sciaenids (Otolithus spp. and Jhonius dussumieri); engraulids (Stolephorus indicus); and leiognathids Leiognathus bindus, L. equilus and Gazza achlamys) constitute 60% (Figure 1)[1]. The fish meal obtained from these resources is now mainly used as an ingredient in livestock, poultry and aquaculture feeds. Considering the rich nutritional status of these low-value fishes, it is felt that these resources could be converted into value-added products viz. pet foods."

Jan 1, 2008

By P. Gray

Process and engineering development of the Warner Zinc Process over the past two decades has proceeded alongside the world-wide collection and analysis of operating and cost data of current processing practices from sulphide ores to refined metals. Study of these data shows that recoveries are dependent on mineralogical characteristics of the sulphide matrix and point to the inadequacy of differential flotation as a tool for preparing feed for smelters. The paid-for return at the mine on the combined metal values in zinc rich sulphide ores rarely exceeds 80% and increasingly runs as low as 50-60%. Surveying the possible alternative ways of improving these performances leads to the conclusion that the Warner Process is the only technology in sight that could meet a target of 90% paid-for recovery and that its development has now reached a point where it can be a fully practicable process for all mixed sulphide ores.

Jan 1, 2000

By Jeffrey F. Adams

Gypsum fouling is a common problem in the hydrometallurgical industry. It is a particular problem in free sulphuric acid neutralization, or iron removal operations where sulphates are removed from aqueous solutions by the addition of calcium-containing bases. Previous work revealed a strong correlation between the degree of gypsum supersaturation in the reactor and the rate of scale growth indicating that scale formation and growth are primarily controlled by chemical phenomena. However, the chemical behaviour of gypsum is variable and unpredictable with solution chemistry and temperature. Many of the "rules of thumb" that are used to predict its behaviour (and avoid fouling) are in fact based on gypsum solubility in water, rather than on real mixed metal sulphate systems. However, despite this unconventional solubility behaviour, we have been able to accurately model it in Ni, Mg, and Zn containing solutions over a wide range of temperature (25°C-90°C) and solution concentration (0-6 m) using the OLI simulation software. Furthermore, by studying fouling rates in a simulated continuous neutralization reactor, the relationship between process conditions and fouling rates were explained for the first time. This has led to an understanding of how techniques for minimizing gypsum fouling work.

Jan 1, 2003

By Ximena Massone

Chile is the most important copper producer in the world and the mining sector plays a key value in its economy. However, at present the country does not have a satisfactory set of regulations about closure and restoration of mining operations. In our country many mining operations will, in the near future, shut down their activities, therefore, it is of utmost importance to elaborate and enforce a set of regulations to prevent risks and to protect the environment. The present study is focused on reviewing and analyzing the existing national regulations about the closure of mining operations and preparing a comparative analysis with other international regulations of countries with mining experience. The final results of the study will be a legal proposal to regulate the closure of mining operations in Chile, aiming at minimizing the potential environmental adverse impact, internalizing the social costs by the relevant operators and defining all aspects of liability for the environmental damage.

Jan 1, 1999

By Katsunori Yamaguchi

The zinc, lead and alumina contents in copper smelting slag are increasing with the increase in waste recycling. The recovery of base metals such as lead and zinc from copper converter slag is important from both an economical and environmental perspective. As a fundamental study of the metal recovery by reduction process, activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag under iron saturation at 1573K are derived from the data of slag-metal equilibrium experiments. On the basis of the obtained data, the activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag were compared with those of the CaO-SiO2-FeOx ternary system. Addition of alumina increases activities coefficient of ZnO and PbO in SiO2 rich side of the slag, and decreases them in CaO rich side.

Jan 1, 2006

By Daojin Cao

The chemical components in the saturated aqueous solution of ammonium dimolybdate (ADM) were investigated at room temperature by comparative Raman spectroscopy. In order to explore the further detailed results, a new method of qualitative and half quantitative analyses, based on the main vibrant frequencies and the intensity ratio of the strongest peak to the second strongest peak recorded in Raman spectrum of saturated aqueous solution of ammonium heptamolybdate tetra hydrate (AHM), was put forward and attempted to analyze the chemical components of saturated aqueous solution of ADM. The results showed that there was obvious difference between Raman spectrum of saturated aqueous solution of ADM and that of ADM, but there were good relationships between Raman spectrum of saturated aqueous solution of ADM and Raman spectra of the three samples including AHM, the saturated aqueous solution of AHM and monomolybdate ion in aqueous solution. It was found that aggregated dimolybdate ion ({Mo2O72-}n)did not exist in the saturated aqueous solution, and was changed into heptamolybdate ion (Mo7O246-) and monomolybdate ion (MoO42-), which were in equilibrium each other, but the distribution ratio of heptamolybdate ion was larger than that of monomolybdate ion. In addition, Raman spectral pattern of saturated aqueous solution of ADM was reported.

Jan 1, 2006

By Burkhard Seeger et al.

The oxidation of copper sulfides can be highly accelerated in the presence of nitrous gases (NOx) as reaction catalysts. Sulfur and sulfate are simultaneously produced in this highly exothermic reaction. This process, carried out in sulfuric acid medium, is performed at an approximately normal pressure and at a temperature of around 110 °C, in a closed container, adding either oxygen or air. The oxidation is automatically controlled through a computer. The process covers the following steps: Catalytic oxidation, filtration and crystallisation of the hot concentrated liquid, electrowinning, mother liquor treatment through jarosite formation, recovery of dissolved copper and zinc and regeneration of industrial water, and non-soluble residue treatment with extraction of sulfur and recovery of silver and gold. No combustibles are needed. No air is contaminated, and no waste water is produced. Solid residues are in a stable, non-toxic and non-corrosive state of equilibrium. Risk of accident is low. Investment costs are small compared to those of the comparable pyrometallurgical process, and production costs are competitive.

Jan 1, 1999

By Toshihide Takenaka

Improvement of corrosion resistance of Mg metal by addition of rare earth metal (RE) was studied, and the effect of surface oxide layer with RE was investigated. The corrosion resistance of Mg was remarkably improved by adding a small amount of RE, and the suitable RE content was clarified. The corrosion resistance of Mg was particularly bettered by conversion coating using a solution including both RE(NO3)3 and Mg(NO3)2. This result indicates that the surface oxide layer consisting of both Mg and RE gives good corrosion resistance to Mg metal. In this study, direct electrodeposition of Mg metal containing RE was also tried in molten chloride with RE chloride, and it was shown that electrolysis could be performed stably. The RE content in the deposited Mg metal was depended on the concentration of RE chloride in the bath and the cathode potential, and Mg metal containing the suitable RE content for its corrosion protection was obtained easily by direct electrolysis.

Jan 1, 2006

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Kimio Itagaki

As a fundamental study for smelting the copper matte with high contents of arsenic and antimony in a strongly reducing condition, phase relations between the liquid matte and copper-rich alloy phases in the Cu-Fe-S-As or -Sb quaternary system and between the liquid matte and iron-rich alloy phases in the Cu-Fe-S-As or -Sb system saturated with carbon were determined at 1473 K by a quenching method. Activities of arsenic and antimony in these systems were also measured at 1473K by Knudsen cell-mass spectrometry. Furthermore, distribution ratios of silver, gold and platinum between the liquid matte and copper-rich or iron-rich alloy phases were determined in relation to the arsenic or antimony content in the systems. On the basis of these data, the elimination of arsenic and antimony from the matte to the iron-rich alloy (speiss) and the recovery of precious metals in reduction smelting of the copper matte were evaluated. It was suggested that the addition of pig iron to make a strongly reducing condition and form the iron-rich alloy, which is fluid at smelting temperatures, will be useful for fixing arsenic in the speiss.

Jan 1, 2006

By Johannes Boonstra

High rate bacterial catalyzed processes can serve to improve hydrometallurgical operations. These solutions are not only economical but also environmental sustainable. With references around the globe, the value of this new approach is recognized by industry worldwide. For instance, metals can safely and economically be separated from process and waste streams using biotechnologically produced sulfide, recovering a valuable metal sulfide product instead of a waste gypsum stream for disposal. Both the natural biological sulfur and nitrogen cycles offer bioconversions that are applied on industrial scale. The shared advantage of these processes is that waste compounds are converted in either a reusable raw material or in a harmless product. This way, natural product cycles can be closed. Applications based upon bioconversions are for example: Sulfur based: Bioleaching, reduction of oxidized sulfur compounds to elemental sulfur, metal recovery with biogenic produced H2S, SO2removal from gas streams, etc. Nitrogen based: Ammonia removal using the anammox-process, biological removal of NOxfrom gas streams, nitrate removal from water streams, etc. Metals: Bacterial processes for the reduction of metals such as uranium, selenium and manganese have proven to offer great potential for clean-up of groundwater streams. This paper contains a description of the above applications. Further, a short introduction on engineered high rate bioreactor systems and a description of industrial biotechnological applications will be provided.

Jan 1, 2003

By V. A. Bryukvin

A characteristic feature of the macrokinetics of the interaction process is the presence of two specifically defined areas of oxidation which had a linear time dependence. The effect of variables, such as residual sulphur content of the melt, temperature and the oxidation potential of the gas phase, on the macrokinetics of oxidation are investigated. Phase composition and structure of products of solidification of partially oxidised melts and thermodynamic properties pentaining to Cu-S-O melts are used to analyze the macrokinetic behaviour and mechanisms of the interaction. The process of interaction of sulfide copper melts with oxygen may be considered as a disproportional absorption process and its mechanism is based on localized interaction on the surface and inside the melt volume. Superficial processes include also the process of primary chemisorption of oxygen by melts at place of metal-metal donor bonds proceeding with formation of oxysulfide liquid solutions and volumetric decomposition of the latter accompanied by evolution of sulfur dioxide and metallization of sulfide melts. It is the degree of dynamic balance of such interaction processes that determines specific individual features of the macro-kinetics and mechanism of oxidation of sulfide copper solutions with oxygen in the gas phase.

Jan 1, 2006

By Manuel Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes the particles to be initially nonporous, have a constant mass prior to fragmentation, and travel at a constant velocity throughout the reaction chamber. The model requires the specification of five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter, and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with experimental data collected in a laboratory flash converting furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow very different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2006

By Y. Prévost

The Noranda Continuous Converting Process was commissioned in November 1997 at the Home smelter in Rouyn-Noranda, Quebec, Canada. It has completed over 18 months of successful operation. Excellent team work and technical expertise contributed to achieve targeted production levels and environmental goals after only a few months of operation. The operating results have demonstrated the flexibility of the process in producing blister copper from a variety of copper feed materials including a combination of molten and solid copper matte, reverts and fluxes. This paper describes the startup activities and process optimization tasks performed during the first year of operation of the new Noranda Converter.

Jan 1, 1999

By Maria de Campos

The pre-reduction behaviour of chromite particles in methane-argon and methane-hydrogen gas mixtures was investigated between 1050°C and 1250°C. Loose bed of chromite particles were reacted in a vertical tube furnace under a pre-set gas mixture predetermined time intervals. Metallization results were obtained for the Cr and Fe components by chemically analyzing the reaction products. SEM-EDAX techniques and X-ray diffraction were employed to elucidate the reduction mechanism. It was found that higher reduction kinetics and higher Cr:Fe ratios in the metal phase would be achieved when hydrocarbon gas was used in comparison to classical carbothermic reduction at a given temperature. The reduction rate was generally bulk gas mass transfer controlled to the reaction site for initial stages which then was followed by ionic diffusion rate control. It is proposed that methane did not partake directly in the reduction but cracked, presenting the reaction site with hydrogen gas and atomic carbon, which was able to immediately react at the immediate area of reduction regeneration CO and H2 and thus maintaining a low partial pressure of oxygen at the reaction site.

Jan 1, 2006

By A. V. Tarasov

The insufficient scientific and technical level of a number of operations in the nonferrous metals industry encourages development of new processes and equipment, including smelting in liquid bath, flame-type sparged smelting unit for combined processes, electrothermal process with the use of alternating current (PDF furnace), electrothermal processing of complex raw materials and intermediate products at nonferrous metallurgical plants, etc. One of the most important aspects for development of new processes and equipment in the Gintsvetmet Institute is their environmental safety. Special attention is paid to environmental protection measures, which is also of important economic and social significance. This refers also to a complete extent to processing of reserves of man-made raw materials and wastes available at the existing operations with the use of innovative techniques ensuring not only resource conservation and environmental protection, but also abatement of negative impact on the nature due to accumulated industrial and domestic waste, reclamation of the land used for waste disposal and recycling of nonferrous metals. Technologies and equipment developed in the Gintsvetmet Institute and based on electrothermal processes determine the prospects for ensuring more integrated usage of ores and man-made raw materials.

Jan 1, 2006

By Boris Arlyuk

The system of short term forecast of metal prices at LME is based on correlation between prices within the quarter forward and at the first place by economic parameters at the West, determining the consumption of metals. Such economic parameters are presented by data of indexes of Western World industrial production (WW IP), official data of IP and Dow Jones indexes at USA. For price forecast within the quarter forward (one day ahead, 3 day -65 days MA forward prices) are significant the changes of actual prices (official and close) at the past and the parameters of daily trade at LME at the past (futures turnover, open interest, LME stocks). It is developed subsystem of price forecast within the quarter forward based on analytical approach determining the relations between the participants of the market. It gives the opportunity to reduce the number of empirical coefficients at the model and receive good accuracy of forecast the MA prices and its direction at the future. Very important part of short term forecast is subsystem determining analytically the probability that the price forecasted for the next trading day will be the maximum or minimum daily price within the quarter forward. The thresholds probabilities are defined by identification the model at the past by maximal commercial efficiency. Such system was tested at the past at period since 2000 till 2005 and gives very high commercial results at operations on 1M forwards and hedging the sales of nonferrous metals traded at LME (primary aluminium, light alloys, nickel, copper, zinc, lead and tin).

Jan 1, 2006