Search Documents

By C. García

Several modifications to Zaldivar's original design have been made in order to reach the design cathode production. This paper describes the modifications to the crushing, leaching, solvent extraction and electrowinning operations, which in turn have increased the production by 14.8% over the design capacity in 1999. The principal modifications were to (1) incorporate a dry pre- screening plant between the secondary and tertiary crushers to increase the percentage of fines to the piles, (2) increase the retention time of the solutions inside of the piles, and (3) increase the efficiency of the tertiary crushers to reduce the particle size of the product material. The leaching ratio was increased from 2.8 to 5.6 m3/ton. The temperature of the pregnant leach solution (PLS) was increased, the amount of acid used was reduced, and a strain of native bacteria was adapted in highly contaminated solutions. The copper concentration in the PLS was increased by more than 50% and was stabilized at this level by commissioning a process of two-stage leaching. The current density in the tankhouse was increased from an average of 2 16 to 3 17 A/m

Jan 1, 1999

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By Esa J. Peuraniemi

Copper smelting to form blister in one single step has been possible for a long time even from low grade concentrates. In spite of obvious benefits, it has been economically viable only with few special raw materials having high enough Cu/Fe and Cu/S ratio. Outokumpu Blister Flash Smelting is currently applied at three operations, and three others will be commissioned in the near future. With typical chalcopyrite concentrates two main obstacles have prevented wider adaptation of direct blister processing: slag formation and heat generation. Oxygen potential in the reaction shaft must be high in order to produce blister with targeted sulfur content below 1%. When large amount of iron is oxidized, as well as sulfur, copper is inevitably also oxidized into slag. High copper amount in substantial tonnages of slag lead on to costly down stream recovery operations to obtain discardable slag. Almost complete oxidation of sulfur and iron releases a high amount of heat which traditionally has been solved by lowering oxygen enrichment of the blast leading on to oversized off-gas line and acid plant. One challenge in direct blister smelting relates to the attack of aggressive high-copper containing slag against furnace refractory lining. In continuously operated Outokumpu Direct Blister Flash Smelting this is taken care of by preventing vigorous melt movement in the settler. Stable bath conditions and stationary slag against refractory lining enable the formation of a protective autogenous layer between aggressive slag and vulnerable refractory. These direct blister smelting challenges are addressed from equipment and process development point of view. New solutions to overcome the obstacles are presented and discussed.

Jan 1, 2006

By P. J. Harrington

The recovery and recycling of low concentration metal and other ions has traditionally been carried out using adsorption or ion exchange processes which, however, become uneconomical at higher concentrations, such as those that occur with many intermediate or waste streams where recycling is now being required. This paper describes the development of a process based on non-dispersive solvent extraction for the recovery of chromium (VI) from electroplating rinse water. During the chromium plating of steel, the concentration of chromium (VI) in the rinse bath rises to concentrations in the order of 100 mg/L when it becomes unusable and is then disposed of. The aim of this work was to investigate processes for recovery and recycling of the chromium in the rinse bath. The recovered chromium is required to be concentrated and purified before reuse. Tertiary amines have been shown capable of concentrating and purifying the chromium (VI) in solution. However, solvent extraction processes that have been applied to the recovery and reuse of metals from waste streams have had only limited success in the past, primarily because of the relatively high solvent losses when existing contacting equipment is used on low feed concentrations. Attempts to eliminate losses by immobilizing these complexing agents on substrates have not been successful. In order to control the losses and maintain specificity, a hollow fibre-contained liquid membrane has recently been trailed in a pilot plant to recover chromium from chromium plating waste streams. Details of the trial and modeling of the results are presented, and show that the level of losses is significantly reduced. However, issues relating to fouling still need to be addressed. This type of equipment has many applications in the recovery and recycling of a range of materials in the manufacturing processes.

Jan 1, 2003

By G. G. Barbante

Copper anode slimes are a valuable source of the precious metals, and selenium and tellurium. They are mineralogically complex and this has led to a great variety of process flowsheets for treating them. The traditional pyrometallurgical method utilises oxidation in a reverberatory furnace, but has numerous shortcomings. Recently deep-bath intensive smelting methods have been developed for use in the larger refineries. Despite these process advances, the thermodynamics of the reactions involved remains poorly understood. An initial description of the thermodynamics of slimes smelting is presented, but is severely limited by a lack of basic data. It is shown that slimes smelting is superficially similar to copper converting, but has many unique features. More basic thermodynamic data on selenium-based systems are needed before the process model presented can be further refined, and work in this direction has already commenced.

Jan 1, 1994

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006

By Nathaniel Arbiter

The first ammonia leaching plants, applied to copper carbonate and native copper tailings in 19 15, were followed more recently by research and development of flowsheets for ammonia leaching of sulfide concentrates. These were applied to two commercial plants. Anaconda's Arbiter Plant started up in 1974 with a design capacity of 36,000 tons/year of cathodes, to be produced by ammonia leaching with oxygen, followed by solvent extraction and electrowinning. The plant shutdown in late 1977 as a result of high maintenance and operating costs, partly due to harsh winters; to complications associated with sulfate disposal; and to changes in mineralogy. BHP's Coloso plant in Chile was designed to produce 80,000 tons/year of cathodes by leaching part of Escondida's concentrate production. Using a similar flowsheet but with air and low temperatures to avoid sulfate production, it started up in late 1994 and shutdown in mid-1998, after failing to reach cathode design capacity, and experiencing problems with its technology. The paper reviews the technologies and also alternative methods for overcoming the problems.

Jan 1, 1999

By C. K. Gupta

Electrometallurgical processes have a definite place in the extraction technology of rare earth metals and alloys. Some of the advantages of the molten-salt electrometallurgical processes include fast electrode reaction, providing accurately controlled large amount of energy to a relatively small reactor volume, negligible over voltage, simplicity of operation, and possibility of accomplishing continuous or semicontinuoue operations. This paper provides a vivid account of the theoretical and practical aspects of electrometallurgical processes for the production and processing of some of the rare earth metals and alloys. Reference has been drawn to the work reported on electrometallurgical processes as applied to the preparation of lanthanum, cerium and misch metal from author's laboratory.

Jan 1, 1992

By Yong Hack Lee

Electric Arc Furnace (EAF) dust is generated when scraps are treated in the electric arc furnace and usually classified as hazardous industrial waste in most countries. EAF dust usually contains 15 to 25% of zinc and 3% of lead. It is usually treated in rotary kiln (Waelz process) or landfilled after a solidification and stabilization treatment. Numerous methods have been proposed as the EAF dust treatment technology, but few of them are in operation as a commercial scale except the Waelz process. Korea Zinc performed a plant test in which 600 tons of EAF dust was treated using TSL (Top Submerged Lance) technology. The TSL technology is a low cost, proven technology for processing zinc-bearing residues. The EAF dust was first de-chlorinated and fed to the TSL furnace. Finally, clean slag satisfying toxicity criteria was generated and valuable metals such as zinc and lead were recovered as fume oxide. The fume oxide was de-halogenated by sodium carbonate and sent to zinc refinery to recover zinc and lead. The recovery of zinc and lead was 90% and 93%, respectively. Most of the dioxin in the EAF dust was discomposed so dioxin less than the Korean regulation limit was detected in the offgas, which proves that the TSL technology is the best solution to treat EAF dust.

Jan 1, 2006

By H. Singh, Anupam Agrawal, H. S. Grewal

"Erosion in industrial appliances causes huge loss of valuable resources especially when solid particles are present in the working medium. A number of erosion models that are available in the literature claimed to predict the erosion response. In this work, five erosion models have been evaluated using computational fluid dynamics (CFD) methodology. Three most commonly used experimental test rigs (solid particle and unsubmerged slurry jet type and pot type) have been simulated and comparisons with the experimental results have been performed. The study helps in understanding the effect of fluid medium and flow pattern on the erosion process. The knowledge acquired shows that phenomenological based erosion models give better results considering the wide range of operating parameters. The in-depth study of the flow field shows the possibility that erosion mechanism, being parameter dependent, could change with location on the same specimen.1.0 IntroductionErosion is a surface degradation phenomenon which causes the removal of material due to impacts either of solid particles and/or bubbles or gas entrained in a fluid medium. Erosion has various categories depending upon the erosion medium such as, solid particles erosion (solid particles entrained in gaseous medium), slurry erosion (solid particles entrained in liquid medium) or cavitation erosion (erosion caused by exploding gas or vapor bubbles). Humphrey [1] has listed 21 different factors that decide the erosion response of the components under a given working condition. The number of factors involved in the erosion process gives us an idea about its complex nature."

Jan 1, 2012

By Milance Mitovski, Milorad Cirkovic, Vlastimir Trujic, Dragana Živkovic

"In this article, it is analysed the possibilitis and the effects utility waste energy of process sulfuric acid production in the existing technical-technological conditions. The utility second process energy, reduction the fuels consumption, reduction environment pollution and its effects are shown, too. High heat quantity is produced as the result of exothermal reactions in the production process of sulfuric acid in Bor. A part of this heat is sufficient for the process development, and significant part of this heat presents low-temperature heat energy that is irretrievable lost. Investigations were carried out based on production of 485 t of monohydrate/day of sulfuric acid. By recovery of this heat quantity for heating purposes, about 20.000 – 25.000 t of coal/year would be saved, what would significantly improve the power efficiency of the smelter copper production. IntroductionTechnological process of copper production in RTB BOR (Serbia) produces a significant quantities of high temperature secondary (waste) heat energy that is uncontrolled “lost” in the vicinity. Secondary heat energy is produced in pyrometallurgical copper production in quantity of 1,621 kWth/kg of dry concentrate or existing heat (that presents a difference of heat at furnace outlet and heat at temperature over temperature of dew point of sulphuric acid gases) in quantity of 1,315 kWth/kg of dry concentrate. For designed capacity of Copper Smelter in Bor, the existing heat power of secondary energy is 92,111 MWt, what is an equivalent to the power of steam-turbo plant where the Rankine-Clausius heating cycle is done, and that is 28,334 MWe."

Jan 1, 2008

By Walter E. McCulloch

Recent laboratory bench scale and pilot plant metallurgical tests at Mountain States R and D International have demonstrated that some copper ores because of relatively coarse copper sulfide mineralization can be preconcentrated by heavy media separation (HMS). In tests with a copper ore from the AMT Copper Creek project near San Manuel, Arizona, HMS preconcentration rejected about 75 to 80 percent of the feed as a minus 13 mm gravel. The HMS concentrates copper recoveries were about 93 to 95 percent. With the incorporation of HMS preconcentration, significant capital and operating costs savings have been projected for the proposed AMT Copper Creek concentrator. An overview of the HMS preconcentration step development for the AMT Copper Creek project is presented. Also presented are other potential applications of HMS preconcentration for copper ore processing.

Jan 1, 1999

By S. F. Cheng

Among the many extraordinary features of the rare earths are their magnetic and magnetoelastic properties. The rare earths, e.g. Tb, Dy, Nd, Sm, are known worldwide for their large magnetocrystalline anisotropy and magnetization, which has led to the importance of magnetic rare earths as vital ingredients of modem permanent magnets. In this paper, we focus on the strain dependence of these giant effects which gives rise to huge magnetostrictions, magnetomechanical couplings, and ?E effects. Magnetostrictions greater than 10-3 have been measured at temperatures as high as 500 K. At low temperatures magnetostrictions reaches -1%. ?E effects - 10. No other solid state material has matched these values. A proper balance of magnetic anisotropy and magnetostriction, plus a proper choice of crystal axes lead to alloys which can switch large quantities of energy between the internal (magnetic) and external (mechanical) states with the application of small triggering magnetic fields. In addition to the traditional use of these materials in transduction, they are particularly valuable for smart systems where reliability and robustness are needed such as active structure stiffening and active vibration control.

Jan 1, 1997

By M. I. Hoschke

The viability of pyrometallurgically treating zinc containing materials is enhanced by recovering zinc metal rather than oxide from furnace gases. During the history of zinc production, there has been continuing development on methods of recovering zinc metal that has resulted in three commercial designs in use today. The most widely used commercial technology, currently producing 13% of the world's zinc, is the lead splash condenser which is attached to the Imperial Smelting Furnace (ISF). The other remaining commercial designs are the zinc splash condenser and the Wheaton-Najarian vacuum condenser. The need to treat increasing quantities of secondary zinc materials, particularly Electric Arc Furnace (EAF) dust, has renewed emphasis on the development of ways to recover zinc metal. Development work in this area has proved to be difficult. Partly as a response to these difficulties, studies into the fundamentals of zinc condensation and absorption have been undertaken. Pasminco Research Centre (PRC), Newcastle, is also developing a. new zinc absorber to recover zinc metal from furnace gases:. The design attempts to address the problems associated with current devices.

Jan 1, 1994

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the influence of Fe+2 initial concentrations in the bioleaching of copper from printed circuit board using Acidithiobacillus ferrooxidans-LR. Printed circuit boards were collected from obsolete computers and mechanically processed through size reduction followed by magnetic separation. The bacteria Acidithiobacillus ferrooxidans-LR were grown and adapted in presence of printed circuit boards. A shake flask study was carried out on the printed circuit boards samples (non-magnetic fraction) using a rotary shaker under the following fixed conditions (185 rpm, 30°C). The bioleaching efficiency was evaluated by comparison between the concentration in the initial sample and in the leached liquor, pH of the medium and concentration of ferrous iron produced. Inductively coupled plasma optical emission spectrometry (1CP-OES) was used to determine the metals concentration. The results showed that Acidithiobacillus ferrooxidans-LR leached 63% copper from printed circuit boards using supplemented medium with Fe+2.IntroductionThe waste of electric and electronic equipment is generated by discarding of equipment such as obsolete computers and cell phones which is stimulated by the technology innovations and it has been growing each year. Because of the amount that has been accumulated it has become a prominent environmental problem but also can be a source of valuable materials, such precious and base metals [1,2] The printed circuit boards are found in almost all electric and electronic equipment being composed of polymers, ceramics and metals and can be an alternative source to recover base and precious metals. The precious metals are used in the printed circuit boards to protect against oxidation and base metals because of its conducting properties [3]. The heterogeneous composition of printed circuit board is a limiting factor in the recycling processes and the metals concentrations also range."

Jan 1, 2011

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By M. A. Halim, V. I. Lakshmanan, T. Sheikhzeinoddin, R. Roy

"Chloride metallurgy is emerging as an alternative process for the production of base metals. Process Research ORTECH Inc. (PRO) has been at the forefront of technological development of chloride metallurgy. PRO has developed an innovative technology for the production of high purity titanium dioxide, iron oxide and vanadium pentoxide from ilmenite ores and concentrates. PRO is also developing its proprietary mixed chloride technology for the extraction of vanadium from other sources such as oil shales. In this paper, results from the test work conducted at PRO for the extraction of Ti and V using a mixed chloride lixiviant are presented.IntroductionTitanium and vanadium alloys and compounds have numerous industrial applications. Titanium dioxide is used in paints, plastics, rubber, paper, inks, textiles and a number of other miscellaneous applications. Currently nanosize T1O2 is being investigated for application in the cosmetics industry. Inorganic sunscreens mainly use T1O2 or ZnO particles, which reflect and scatter ultra-violet light. T1O2 nanomaterial is also finding application in smart construction materials and coatings, as a photo-catalytic converter. Nano TiO2 can catalyze the dissociation of NOX gases and other automotive emissions, thereby reducing the smog in urban centers. After the construction material is exposed to sunlight or ultra-violet light, the T1O2 is photo-activated and degrades the pollutants.Titanium metal and titanium dioxide are produced from ilmenite (FeTiOs) or rutile (naturally occurring T1O2) ore. Only about 6% of the titanium resources are used to produce titanium metal and the rest is used to produce T1O2. Many of the titanium ore deposits currently have unacceptable levels of transition metals which limits their processing by conventional routes."

Jan 1, 2012

By Douglas Robinson

This paper describes technical work done to develop a Spouted Bed Electrode Cell into a commercially viable Electrowinning Cell; (a previous paper has been presented at the ECS meeting in Paris in May of this year, with a more general overview of the cell, [1]). The studies have included hydrodynamic tests to understand the criteria for the circulating flow of metallic beads in the cell, particularly in the region at the entrance to the draft tube, and electrochemical tests to find a suitable diaphragm for extended time electrolysis. Various patent pending features were developed including a double nozzle to allow for automatic stopping and restarting of the bed, an arrowhead shaped draft tube to control the flow of beads into the entrance to the draft tube, a roof-top shaped device to control the flow of beads out of the top of the draft tube, an overflow weir to allow the continuous recovery of beads from the cell, and a family of diaphragm fabrics for extended operation. Prior to the identification of the diaphragm material, short circuits would develop within a few hours. A pilot scale cell was operated for three days, with continuous operator attention, and then for ten days with operator attention only on day shift. The cell is currently advancing to the next stage of development which will involve continuous testing in a commercial copper electrowinning facility.

Jan 1, 2003

By Isabel Lázaro

A detailed study has been undertaken into the electrochemistry of the leaching of chalcopyrite in acidic solutions containing ferric ions. Mixed potential measurements have shown that the maximum potential achievable on a chalcopyrite disk in a ferric sulfate medium lies within the so-called passive or prewave region in the anodic behavior of chalcopyrite. The very low current densities due to the anodic oxidation of chalcopyrite at potentials in the region of the mixed potential has made studies of the initial stages of dissolution difficult. However a careful rotating ring-disk electrode (RRDE) study has enabled data to be obtained for the stoichiometry of the initial dissolution reaction to be obtained. Thus, in addition to the detection of soluble iron and copper as products in this potential region, a soluble sulfur species has also been detected. A comparison of the experimental with the expected collection efficiencies of the products on the ring has revealed that this soluble sulfur species is likely to be thiosulfate. The characteristic transient anodic behaviour of chalcopyrite in this potential region has been interpreted in terms of a rate limiting solid-state diffusion process. Thus, extrapolated rates based on reported measured solid-state diffusion coefficients for the mineral at elevated temperatures have been shown to be consistent with the potentiostatic current-time transients. Furthermore, comparative studies of the anodic characteristics of the copper sulfide minerals covellite and bornite has confirmed their greater reactivity in this potential region. The results of this investigation have been combined with a parallel study of the non-oxidative behaviour of chalcopyrite in order to derive a model for the dissolution process which is consistent with other published studies of the electrochemistry and dissolution of the mineral.

Jan 1, 2003