Search Documents

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By Max J. Spendlove

This Bureau of Mines publication reviews current recycling trends in the United States. Although near-term prospects are poor for recycling most present wastes, urban refuse is an important exception. Such wastes comprise a mine above ground, and much less processing energy is normally required to recycle the constituents of urban ore than to obtain them in equal amounts from natural raw materials.

Jan 1, 1976

By Chamila Jinendra Nanayakkara, Nimila Dushyantha, Amila Sandaruwan Ratnayake, Gayithri Niluka Kuruppu

Rare earth elements (REEs) are key ingredients in many advanced materials used in energy, military, transportation, and communication applications. However, the prevailing geopolitical dynamics and the rising demand for REEs have rendered the reliance on primary REE resources susceptible to future supply disruptions, posing a substantial risk to the availability of these elements for numerous applications. Therefore, it is imperative to undertake substantial initiatives in the extraction of REEs from secondary sources on a large scale to ensure the resilience of the supply chain. Permanent magnets, lighting phosphors, and nickel-metal hydride (NiMH) batteries are among the secondary sources with high potential for sustainable REE extraction. This review assesses the extraction potential of REEs from the aforementioned three secondary sources and their leaching kinetics and thermodynamics aspects. More importantly, state-of-the-art different existing kinetic models employed in rare earth (RE) leaching were well discussed for a better understanding of the REE leaching reactions. Furthermore, the optimized leaching parameters related to this kinetics were described, and various RE recovery methods were comprehensively summarized. These processes facilitate to managing one of the fastest-growing solid waste streams by minimizing environmental impacts and producing critical metals, including REEs via circular economy approaches. The recovery of REEs from secondary sources aligns with numerous United Nations Sustainable Development Goals (SDGs), particularly in the renewable energy sector for climate change mitigation. Consequently, this trash-to-treasure urban mining concept to transforming e-waste into a valuable resource for REE recovery emerges as a pivotal element within the REE industry.

Dec 28, 2023

By R Norris, M Dunne

Mining and mineral processing is expected by society and obliged by law to operate in an environmentally friendly fashion, minimising the impact on and avoiding damage to the environment. Substantial efforts by the industry, as well as by process and equipment designers have resulted in many innovative developments, which show that operating in an environmentally responsible manner can be achieved in a cost-effective way. This paper showcases five emerging equipment best practices in industry including installation examples. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. The belt press filter is a small fraction of the operating and capital cost of alternative dry tailings technologies. This gives operators who must dry their tailings a competitive advantage and makes such ægreenÆ operations much more sustainable. The filtercake is disposed with other plant rejects, eliminating the need for tailings dams to be constructed and thus also often increasing mine reserves. Mining applications include coal tailings, sand tailings, sinter plant waste and power station fly ash. Screen-scroll and vibrating centrifuges are widely used in the coal, potash and salt industries to dewater the product to low surface moistures. Inclined plate Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the worldwide production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By R. E. Collom

The commercial development of petroleum and natural gas fields has reached its present status within 60 years and is still considered by some operators to be "100 per cent wildcatting." 1 A tendency to drill for gusher production, the production that yields big returns in spite of any mechanical defects in drilling methods, has frequently caused drillers to pass by oil-bearing strata of comparatively small yield and actually to overlook rich oil zones in proved fields; in addition, whole fields have been ruined by water because development methods were never carried beyond a hole-in-the-ground stage.2 Unfortunately, the petroleum industry has no mine dumps or tail. ing piles as at metal mines to yield fortunes through later and bette!' methods of treatment. The wasted oil and gas are gone, as are the time, money, and effort wasted in ill-advised or haphazard drilling. Probably as production costs increase less oil will be wasted, but the need to develop and produce from sands of low yield will become more urgent with the increase in consumption of oil and the decrease in supply. Hundreds of wells are producing steadily as the result of months and perhaps years of careful prospecting and of tests during drilling. The Bureau of Mines has studied the testing and drilling methods used at such wells, and presents in this paper a criticism of these methods and suggestions on future work. The term pr08- pecting here means correct identification and measurement of strata as they are exposed by the drill. The term testing means the determination of the kind and amount of fluid stored within the pores or crevices of any stratum exposed in the hole.

Jan 1, 1922

Uranium exploration over a wide area of the Southern Frame Embayment, South Australia, has defined a number of Lower Tertiary fluvial palaeochannels incised in older rocks. The buried channels contain similar stratigraphicsequences of interbedded sand, silt, and clay, probably derived from the adjacent uranium-rich Olarv Provinee. Uranium mineralization is pervasive within two major palaeochannels, and four small uranium deposits have been found in the basal sands of these channel sequences, at the margins of extensive tongues of limonitic sand.One of the channels is examined in detail with respect to channel morphology, stratigraphy, and rock alteration and the geology and ore controls of the contained uranium deposits are described.A geochemical zonation reflected by variation in limonite, pyrite, carbon, and humic malleI' is defined across one of the deposits. A genetic model is proposed suggesting formation by a uraniferous geochemical cell which migrated down the stream gradient and concentrated uranium on its lateral margins adjacent to the channel bank.

Jan 1, 1978

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013

By C. Bachmann, M. J. Laurila, A. J. Widenman, A. Klein

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA's Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison's Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of online analyzers (ISO/DIS15239).

Jan 1, 1999

Geology grads mine heated job market Salaries up 44 per cent in three years ?[Geology student] passed up a $100,000-a-year job at a mining company last December when he finished his degree in geology. The 24-year-old Canadian said he?s confident he?ll get a better offer.? Rob Delaney and Stewart Bailey, Calgary Herald, Published: Saturday, March 15, 2008 Massive shortages across the mining industry > Trades and operators are a large component > Technical people are equally hard to find > Students are in an excellent positions to secure exciting jobs > Experience is at a premium. Why?

May 1, 2008

By P. Roman, L. Daneshmend

"During the last decade, mining companies have been overwhelmed by technological solutions to perceived problems. This is particularly true with information technology where rapid advances have resulted in a professional climate characterized by technomania — the perception that failure to adopt emerging technologies will result in a loss of competitive advantage. This paper describes the applicability of structured analysis and design techniques as an appropriate methodology for integrating emerging technologies in the mining industry. The potential of this approach to improve overall mine effectiveness through improved communication and co-ordination between operations and maintenance is discussed. IntroductionA strong working relationship between the operations and maintenance departments in both open pit and underground mines is fundamental to the overall success of the mining endeavour. Unfortunately, for many mines, this characterization is far from accurate. Short-range production targets dominate the day-to-day management of the mines. This can be seen in Bostwick and Buchanan’s (1993) report on American Barrick Resources efforts to achieve an aggressive 415 000 tpd mining program at their Goldstrike operation in Nevada. When production managers do not meet their quotas, the finger is often pointed at maintenance. As a result, a confrontational culture can develop between the two organizations, resulting in a lack of cooperation that exacerbates the problem. Historically, production planning has taken priority over maintenance planning. This is reasonable since production is the primary purpose of the mine with maintenance serving in a support role. This basic relationship remains intact today. However, the trends toward mechanization, increasing levels of automation, and larger equipment, have resulted in increased reliance on the equipment used in the mine. As a result, downtime costs now go well beyond the direct labour associated with the repair of the machine. Lost production costs due to downtime resulting from failed equipment are becoming an increasingly important factor in determining a mine’s overall economic performance."

Jan 1, 2001

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By Michael J. Miller

In the design of a modem mill, a stockpile storage system for raw and/or semi-processed ore has become almost indispensable. This paper discusses the benefits of such stockpile storage as well as the various types of belt conveyor stockpiling units available. Particular attention is given to large radial stackers since they offer the greatest flexibility. Stacker control systems and accessory equipment are briefly discussed. Various alternative reclaiming arrangements for stockpiles are reviewed and a discussion of the advantages and drawbacks of each arrangement is included.

Jan 1, 1979

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By E. A. Has, E. Mcl. Tittmann

Double roasting of sinter carrying a high percentage of lead concentrates, gave rise to the problem of removing the sheets of metallic lead formed in the wind boxes. The solution of the problem has been found in the water sealed wind boxes. The metallic lead is granulated and can be removed without seriously interfering with the operation of the machine and eliminates necessity of men going in wind boxes with air guns. THE practice of double sintering the charge for lead blast furnaces, which is now standard throughout the lead smelting industry, has introduced the rather difficult problem of cleaning the wind boxes on sintering machines used for the final pass. Two factors have more recently accentuated this problem: (1) the growing demand of workmen for better working conditions and less arduous labor, and (2) the growing dearth of crude lead ores and the improved grade of lead concentrates demand a charge carrying the maximum percentage of lead. One to 2 pct of such high lead charges (30 to 40) when processed on machines in reasonably good condition will pass through the grates and report in the wind boxes. One-half to three-quarters of this material will be metallic lead reduced by the coke breeze or other fuel mixed with the charge. This lead forms large cakes or chunks which are hard to remove and which substantially increase the time the machine is out of operation for cleaning the wind boxes. A high lead fall can reduce the operating time 30 pct. As a specific example, a 30 ft machine having 63 in. pallets, and equipped with three conventional wind boxes, requires 3 to 4 hr per day for removing the accumulation in the wind boxes when operated as a final pass machine. This same machine when operated on raw charge requires less than an hour per day for cleaning. To eliminate formation of large chunks of lead in the wind boxes of the final pass machines and time lost in cleaning the boxes, R. C. Rutherford of the Chihuahua smelter of the American Smelting and Refining Co., devised and patented* a wind box having a water bath to granulate the lead as it falls from the grate bars. Later, C. H. Harris of the San Luis plant made and patentedt an improvement on Rutherford's device in which the water bath seals the wind box in a manner permitting the latter to be readily cleaned without destroying the vacuum. The first machine to our knowledge to use the water bath box was at the Chihuahua plant along the lines of the Rutherford patent. In 1942, a machine was placed in operation at the El Paso plant which incorporated the features of both Rutherford and Harris. This machine is 40 ft long equipped with pallets 63 x 24 in., and having 4 wind boxes 10 ft 4 in. x 7 ft 2 in. x 51 ft 3 in. in size (fig. 1). The air from the fourth box is returned to the first three, and the gas from the first three discharged to a baghouse. The machine has conventional drive, discharge hopper,

Jan 1, 1951

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

The arbitration process, and its drawbacks: Any time you have taken part in a major arbitration, and the decision, when it comes out, is not what you thought it would be (which is bound to happen occasionally), the normal reaction is something like æthe arbitrator got it wrongÆ. Again normally, when you have cooled down a bit, and you look in more detail at the decision, you can see, probably, æwhere he got it wrongÆ (it is only male arbitrators who get it wrong). Ultimately, when reason prevails, and you reflect on it, you can see that what really happened was that you failed to get the arbitrator to see what you were getting at in the point or points concerned. This is doubly frustrating, when you consider what has been involved in getting to this point, having been through it all at least twice. An alternative to this process may be the dispute review board.

Jan 1, 1999