Search Documents

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By John Parianos, Simon Richards

SUMMARY The Clarion Clipperton Zone (CCZ) hosts the most valuable deposit of polymetallic nodules yet discovered. Understanding the geology of this deposit is key to its effective exploration and mining. Nautilus Minerals (via its subsidiary Tonga Offshore Mining Limited; TOML) has been progressing its understanding of the relationship between seafloor morphology/structure and nodule abundance/morphology, both locally (within its contract areas), and globally (across the CCZ and the span of its contract areas of almost 70% of the CCZ). We present the first results of a project with the aim of developing a method to quickly and accurately map seafloor morphology/structure (Tectonic Subcomponent scale) without the necessity for high resolution seafloor multibeam data. Furthermore, the results presented here will allow a first attempt in understanding the relationship between seafloor geomorphologically-defined zones and plate-scale tectonics of the CCZ and adjacent plate segments. INTRODUCTION A relationship between the type of geochemical active layer and nodule abundance/morphology has long been understood (ISA, 2010). Consideration of the range of differing nodule types found within, but especially between, the TOML contract areas allowed Parianos and Pomee (2017) to refine this relationship further via interpreted thickness and dynamism of the geochemically active layer. The scale of the deposit, both in terms of space and time is staggering (a 10-20 cm thick deposit, spanning almost 4500 km, varying within a circa 10 Ma period), but a segment wide geological map may one day prove to reflect controls on nodule formation and distribution.

Jan 1, 2018

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By K. V. Raj

"Air inversion is a meteorological phenomenon generally occurs during winter times. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for health and safety of miners. Mine operations cease if the concentration of NOx or CO exceeds the threshold limit value (TLV) of the pollutants. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Studies of the turbulence parameters suggest that effective ventilation of the pit and removal of pollutants can be accomplished if a large enough mixing length in the open pit can be created. Turbulent mixing by eddies of different length scales under an inversion layer is product of wind shear, thermal gradient and buoyancy. The main result of turbulence is mixing of the atmospheric profile and transport of momentum. Computational fluid dynamics (CFD) Simulation results of a novel mitigation approach using cloud cover will be presented in this paper. INTRODUCTION In extreme climatic conditions, deep open-pit mines tend to trap pollutants at the pit bottom due to air inversions. Keeping open pits adequately ventilated is a considerable challenge for the mining community. Mine operators in cold regions are very familiar with this problem, the severity of which can be judged from Figures 1 and 2. The top portion of the figures show clear sky and snow covered benches. The brown haze, containing various contaminants accumulated over time in the pit under the air inversion, can be seen in the bottom portion of the figures. Several Arctic or subarctic mines have reported air inversions. Even Rio Tinto’s Bingham Canyon pit in Utah has reported local air inversions from time to time [1].Mitigation of pollutants in deep open-pit mines in the Arctic is a challenging task. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for human health. Mine operations cease if the concentration of any one of the pollutants (NOx or CO) exceeds the TLV. Sustained cessation of a mine operation has serious economic consequences. For continued mining operation, the levels of pollutants must be below the TLVs. If no significant synoptic meteorological situation changes during an inversion, a warm air mass sits over the cold air mass within the open pit. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Some of the early approaches in artificially ventilating open pits were attempted in the USSR. Most of the studies by Soviet researchers suggested the use of turbojets and turbo-propeller engines, airscrews, axial pit fans, and meteotrons [2, 3]. However, the majority of these studies were only theoretical in nature, with no evidence of an approach that really worked in practice."

Jan 1, 2017

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By E Nik, A Manzoori, H Namavari, P Witt

The smelter building at Sarcheshmeh Copper Complex, Iran, houses two reverberatory furnaces and five Pierce-Smith converters. Under normal operating conditions SO2 emissions fill the building, posing a major health problem for all workers in the building, and reducing their ability to maintain the plant. The converter fume extraction system was analysed using plant measurements, engineering modelling of the entire system and CFD modelling of the extraction hoods. By applying fundamental engineering concepts, a user-interactive computer program was developed that enabled plant engineers and operators to gain a detailed understanding of the system. In conjunction with plant measurements, the model quantified the amount of inleakage throughout the system, identifying it as a significant contributor to the poor extraction performance. Furthermore, it enabled investigation of the effects of hood gates, converters on line, hood dampers, flue insulation, electrostatic precipitator (ESP) operation, and inclusion of an acid plant. The model gave unprecedented insight into the operation of a counterintuitive buoyancy-driven extraction system.

Jan 1, 2004

The addition of copper sulfate to mineral slurries in order to ?activate? sulfide mineral surfaces for enhanced collector molecule adsorption, and hence enhanced recovery via flotation, is a com-mon mineral processing practice. It has been established in a laboratory situation that the addition of CuSO4 in conjunction with xanthate collector increases the flotation rate of pentlandite as compared to the addition of collector alone. However, it remains unclear whether the addition of CuSO4has a similar effect within mineral processing circuits. We examine here the effect of pre-activation oxidation on the copper activation of pentlandite and monoclinic and hexagonal pyrrhotite. All activation experiments were carried out at pH 9 using a total solution content of copper ions equivalent to one monolayer (0.210 -4 moles, 110-4M). Copper loss from solution was extremely rapid in all cases with less than 10 % remaining after 10s. EDTA extraction and solution analysis clearly demonstrated that copper activation was via direct surface adsorption and not an ion exchange process, as is the case for sphalerite, and that most copper on the surfaces is in the form of Cu(I). ToF-SIMS analyses of the mineral surfaces subsequent to copper activation show increased surface oxidation on increased conditioning time prior to copper activation. However, there is a significant decrease in surface oxidation on comparison of samples that have otherwise been prepared in the same manner but where one has been exposed to copper solution rather than water. This suggests that copper activation stabilises the surface and reduces the propensity for oxidation. Regardless of the length of pre-activation oxidation time only Fe(III) (no Fe(II)-S) was observed by XPS analysis, indicating a highly oxidised surface layer dominated by Fe-O-OH species. The presence of Cu(II) on the mineral surface is indicative of the formation of Cu(II)-containing precipitates and indicates non-mineral specific activation resulting in increased recovery but lower grade. Mineral specific copper adsorption, as evidenced by the presence of Cu(I), is required to improve both grade and recovery. Prolonged oxidation prior to copper activation causes a reduction in the Cu(I) to Cu(II) ratio on the mineral surfaces as compared to either fresh surfaces or surfaces oxidised for 1 minute only. This strongly indicates that the copper activation process is less effective on highly oxidised surfaces.

Jan 1, 2014

By H. W. Gillett, G. M. JAMES

In its work on mineral wastes the Bureau of Mines is studying losses in the melting of nonferrous metals and alloys. The greatest of these losses is that of zinc through volatilization in brass melting, but another and considerable loss is that of aluminum and its alloys in the melting of finely divided material. In order to get some idea of the magnitude of the loss in melting aluminum scrap and to find out what methods of melting were used information was gathered in regard to present practice; also experiments were conducted to obtain some data on the relative merits of different methods. As the experiments could be made on a laboratory scale only, they were not expected to solve the problem entirely, the object in making them being rather-by indicating which methods were of greater promise-to narrow the field over which largescale tests and comparisons need be made by those commercially nterested in the problem of melting scrap aluminum.

Jan 1, 1916

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Arthur E. Morris

The primary market driver for improving process technology is innovation, which requires a skilled and educated workforce. However, many Materials Science and Engineering departments have eliminated extractive metallurgy and chemical thermodynamics from their curricula, yet these topics contain the necessary fundamentals for process innovation. As a result, most MS&E students are ill-prepared for careers in processing. The dearth of processoriented MS&E curricula has prompted some Universities to develop a “shared” effort to offer distance education between multiple institutions [1]. A target audience for a shared process simulation course would not only benefit students, but also be a basis for an on-line course for practicing engineers faced with new or changing career choices. To fill the gap, the basics of a process simulation course was developed in an abbreviated form as series of eleven articles and Excel workbooks published in Industrial Heating magazine between July 2012 and July 2013.

Jan 1, 2014

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

By Peter B. Knuckey

1, Introduction Location Kalengwa mine is located in the North Western Province of Zambia, 402 kilometre by unpaved road to the west of Kitwe, which is roughly in the centre of the Zambian Copperbelt, well known as one of the world&apos;s centres of copper mining. Its position is illustrated on the map of Africa in Figure 1 and on the map of Zambia in Figure 2. It is a mine of Roan Consolidated Mines Limited whose other properties, Mufulira, Luanshya, Chambishi and Chibuluma Mines, are all located on the Copperbelt. It is managed by the Chibuluma Division of the company. The rate of production from Kalengwa will vary from 12 000 to 17 000 tonnes of saleable copper a year over the next six years. Kalengwa did not exist as a place until the first prospecting parties and later the mine became established and the early working population was recruited entirely from small villages in the surrounding area as much as thirty miles away. The mining area consists of fourteen mining locations amounting to 3.35 square kilometres and the land may be used for any purpose connected with mining, including housing, wood cutting and other utilities. The whole area is, except for minor undulations, a fairly flat plateau with main rivers running from north to south and flood basins known as "dambos" located in a general east west direction. Vegetation is, with the exception of the grassy dambos, temperate forest with relatively light undergrowth. Game of great variety is prolific, as is the associated tsetse fly.

Jan 1, 1971

By R. Armstrong, C. Ware, P. Sudan, G. Whitmore

The northern KwaZulu-Natal (KZN) coastal dune cordon, South Africa, extends from north of Durban into Mozambique. The Quaternary dune cordon, which can be up to 2 km wide, comprises a series of stacked, unconsolidated dunes that in places attain a height of over 100 m. Mining of the dunes produces much of the world’s supply of ilmenite, rutile and zircon. This paper documents the age of zircon grains separated from dune units, identifies likely source rocks and presents an evolutionary history for the dune cordon. Between 30 and 60 detrital zircon grains from three distinct units from the northern KZN coastal dunes were analysed for U/Pb isotopic ages using the SHRIMP II at the Australian National University. The samples represent units from the base (ca. 250 ka; luminescence age1),middle (ca. 190 ka2) and upper (ca. 20 ka2) portions of the coastal dune cordon. Zircon grain ages identify three source populations: (1) a 1 000 to 1 200 Ma group correlated to the Natal Metamorphic Province, (2) a 500 to 650 Ma group representing a Pan-African belt, which may correlate to the Mozambique Belt and (3) a ca. 650 to 800 Ma group of unknown provenance. Surprisingly, the presently exposed basement, comprising the Kaapvaal Craton and Archaean volcano-sedimentary sequences, has not supplied a significant amount of zircon grains (< 5%).This suggests that unroofing of basement rocks in the region has only occurred during the last 20ka. In addition, the absence of zircon grains younger than 500 Ma indicates that the bulk of zirconis not reworked from the Karoo Supergroup cover succession, but may be sourced by reworking of the Natal Group sandstones.

Jan 1, 2003

This paper describes the behaviour, under creep conditions, of a cast lead creep specimen consisting of five crystals, the boundaries of these crystals being substantially at right angles to the direction&apos; of tension, i.e., across the long axis of the specimen. This particular specimen was obtained in an attempt to produce a single crystal in the manner described in the appendix of a previous paper (1).Thus, the specimen was of the same shape and size, was composed of the same purity lead and received the same preliminary treatment as the single crystal test-pieces.The object of the experiment was mainly to observe the effect of the crystal boundaries on both the deformation of the test piece and the process of recrystallisation and to compare the creep rate of the test-piece with that of a specimen consisting of one crystal only.EXPERIMENTAL METHODThe specimen had an effective test length of 10 cms. and a cross $ection of 0&#183;5 in. x 0&#183;25 in. In Fig. 1 is given a sketch of the specimen to scale showing the positions of the crystal boundaries on all four surfaces. Except for those of crystal No. 4, which was confined to approximately one-half the cross section of the specimen, the boundaries of each crystal traversed the four faces.The specimen was mounted in exactly the same manner as the single crystal specimens. During the creep test, it...

Jan 1, 1941

By G. E. Murray

Introduction The development of the method for recovering zinc from lead blast-furnace slags at Trail is interesting and important in the history of both lead and zinc metallurgy. Many efforts have been made in the past, particularly in Germany, to make economic recovery of zinc from slag. The Pape process on Oker slags was successful and is being worked at the present time. More recently the Waelz process has come to the fore. One effort at Cockle Creek, Australia is of special interest in view of subsequent developments. This was re-ported in detail by Guy Courtney in 1920(1). It deserves mention as it shows how, as in many other instances in the metallurgy of lead and zinc, important pioneering work has been done in Australia. These experiments, started over 25 years ago, comprised reduction with coke, powdered coal, and eletrothermically in carbon-lined furnaces. The so-called slag eye furnace, which volatilised the metals from a blast furnace running with a hot top, was also investigated.

Jan 1, 1933

By Firth B. A

The flotation of fine coal (minus 0.5 mm) often requires the addition of an insoluble hydrocarbon collector to apparently promote the adhesion of coal particles to air bubbles. A series of experiments was conducted using a radiotracer and narrow size fractions of clean coal to determine the effect of particle size distribution, collector addition rate, desliming of feed and emuIisification of collector on the distribution of collector between the different size fractions. The concentration of collector per gram of each size fraction was found to be approximately proportional to (average particle size)-2 except if the collector was emulsified prior to addition, the dependence altered to approximately (average particle size)-1. Mechanistic consequences are discussed.

Jan 1, 1982

By Michael D. Balen

The Bureau of Mines (Bureau), in cooperation with the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted field investigations from 1987 through 1989 in the 5.7 million-acre Valdez Creek Mining District (VCMD) in south-central Alaska. The objective of the VCMD investigation was to evaluate the mineral resources and the mineral development potential of the mining district. The investigation was part of the Bureau&apos;s continuing statewide mining district evaluation program. Nineteen new mineral occurrences were identified as a result of this investigation. Reconnaissance placer sampling resulted in the identification of 10 previously unreported occurrences that primarily contain gold, however, some contain subsidiary platinum-group metals and/or tin. Reconnaissance lode sampling resulted in the identification of two gold-silver occurrences, three platinum-group metal occurrences that contain elevated quantities of subsidiary chromium, nickel and/or cobalt, three copper occurrences that contain subsidiary molybdenum or zinc, and one zinc occurrence.

Jan 1, 2011