Search Documents

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By B. D. Thomas

When the origin and early plans, of Battelle Memorial Institute were described in this journal in October 1929 by R. W. Gillett the first director, the doors of the laboratory had just been opened and the hope of the founder that the institution serve the world by research for industry still existed only as an ideal in the minds of the thirty or so employees who then constituted the staff. Since that time the country has experienced troublous times. A devastating depression plunged the entire world into an unprecedented period of financial and industrial inactivity; and the slow recovery of the late thirties was soon to be overtaken and overwhelmed in the violence of war. Through this time of stress Battelle has continued to grow. The staff has increased to almost 600; buildings and equipment have been added, until now it stands in a place of pre-eminence in the metallurgical and engineering world.

Jan 1, 1944

By Frank Hirthammer

The paper explains the procedure of implementing Track & Trace solutions for manufacturers of explosives based on customer experiences. By using concrete examples, the process from project start to implementation is described. Lessons learned from the experiences of European explosives manufacturers are presented.

Feb 1, 2020

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By G. W. Thomas

Jan 1, 1967

By Ali Montaser

Hauling trucks are important part of equipment fleets for large earthmoving operations such as those encountered in dams and highway construction projects. This paper presents an automated methodology for tracking and estimating productivity of hauling trucks fleet operations in near-real-time. Recent advancement in automated site data acquisition technologies made their use in tracking and monitoring of construction operations feasible. However, these technologies fail to track hauling truck fleets due to the change in the cut and fill locations from one cycle to another; making tracking and progress reporting difficult and inaccurate. In addition, there is very little work done utilizing data sensed directly from equipment, for example sensing when truck dumping bed is raised during the dumping process. The technologies deployed in the developed method are Radio Frequency Identification (RFID) and equipment control sensors. Low cost passive RFID tags are attached to hauling trucks and fixed RFID readers are attached to loaders or excavators. The read range of the used RFID tag is centimeters, to be activated only when a loader with an attached RFID reader is loading a truck. On the other hand, control sensor is connected to the truck control system and operated by the motion of its movable bed. The function of control sensors is to record the signal time when the truck operator gives order to the truck control system to raise or lower truck bed. The captured data is then transferred wirelessly from the RFID reader and control sensor to a computer housed in one of the temporary offices onsite and subsequently to the main server in the contractor?s head office. Fusing the data captured from RFID reader and control sensor is used to identify loading, travel, dumping and return time that constitute the hauling truck cycle time. The collected data is analyzed and processed automatically, without human intervention, to calculate the productivity of the hauling truck and to report it directly to onsite personnel. Relational database is developed to support the implementation of the proposed method. The developed database is used to process the data captured by the RFID and the control sensor to calculate the productivity achieved in cutfill operations in near-real-time. The developed methodology is expected to facilitate early detection of discrepancies between actual and planned performances.

Aug 1, 2013

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By BION J. ARNOLD

WE can, I think, rightfully claim, irrespective of our faults, that engineers must, in order to last as engineers, possess the qualifications of integrity, stead- fastness of purpose, ability to think straight, and to apply these qualities consistently and continually in their everyday work. All engineers know this, most of them conform, and in order to drive it home I might, if 'clothed with proper authority, preach to you at length, but I shall not take the chance. So I only want to make a suggestion or two to the young engineers. Have an ideal and work toward it. You will have your disappointments and your temptations but keep your record clean, and if anyone says you are foolish or ugly, or homely, or that you need a guardian, take the criticism with a smile, for he may be able to prove his contention; but if he attacks your integrity, strike at once and fight hard, for he has assailed not only your character but your principal asset as an engineer.

Jan 1, 1929

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By R. S. Dean

This is the fourth of a series; of annual report of the Metallurgical Division to be released in this form and cover the fiscal year July 1, 1937, to rune 30, 1938. This report is not merely a recitation or brief of the year's work; it contains technical information in usable form, although a some of this has appeared or will he issued in greater detail in separate reports. The table of contents that follows fists the principal investigations accomplished and those that are being continued. Other projects are being begun and contemplated for the next year.

Jan 1, 1938

By R. S. Dean

[During the past year the Metallurgical Fundamentals Section gave about an equal amount of time to the experimental determination of fundamental thermodynamic constants and to the demonstration of the application of such data to more directly practical metallurgical problems. The first division of the work - the actual experimental measurements of typical thermodynamic constants - was carried out an two problems, termed ?continuing? programs, namely, (1) measurements of Specific Heats at Low Temperatures and (2) Measurements of Heats of Formation and Free Energies. Specific substances chosen for investigation are classified as (n) those that have been the subject of requests for information from the industry and that, upon examination, seem of sufficient practical importance to justify study, and (b) compounds that are difficult to treat metallurgically, or whose specific thermodynamic properties have not yet been determined satisfactorily and for which accurate data might suggest improved or new methods of Metallurgical treatment, or (c) materials recognized as belonging to a social class with exceptional thermodynamic properties and, hence, of scientific as well as technical importance.]

Jan 1, 1938

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Andrew Cecala

The Bureau of Mines performed tests to compare the effectiveness of steam and of water sprays to reduce respirable dust levels at mineral processing plants. By applying 0.22 wt pct water vapor as steam to product material, a 64-pct respirable dust reduction was recorded. By applying the same amount of moisture with water sprays, only a 25-pct dust reduction was recorded. By increasing the moisture content up to0.5 pct using water sprays, the dust reduction was increased to 55 pet, which was still less than the dust reduction achieved by adding less than half that amount of water in the form of steam.

Jan 1, 1985

By Erik Melchiorre, M. Katherine Crombie, Dante Lauretta, Chris Gholson

Rich Hill, also known as Weaver District No. 2, is among the most productive placer gold locations in Arizona. Located near Congress, AZ (Fig. 1), this district hosted major placer rushes in the 1860s and1930s. Those rushes were followed by an electronic metal detecting rush that started in the 1980s and continues today. Thousands of ounces of gold have been produced by these modern amateur and professional metal detectorists. Many of them see more gold in an afternoon than Nevada mine workers will ever see outside of the mill. Rich Hill discovery Inspired northeastward by Spanish legends, a party of 10 men left Yuma, AZ on April 1, 1863. Included in the group were Pauline Weaver (Fig. 2), Henry Wickenburg and Abraham Peeples. Wickenburg left the group near the Hassayampa River and discovered the Vulture deposit. The rest of the group arrived at the base of Rich Hill in late May. While drying antelope meat on the first day, a few of the men prospected a nearby creek bed and immediately found gold. In a couple of hours they picked up more than 2.8 kg (90 oz) of gold. The next day, four members of the party went searching for their horses and returned with news that a nearby hilltop was literally graveled with nuggets.

Jan 1, 2003

A key driver to the success of a tunnelling project (the project) is the management of hydrogeological risk. The hydrogeological risk, if not managed, may cause significant impacts on the overall performance of the project. Impacts may include groundwater quality impairment due to contaminant transport and acid drainage from disturbed geology to groundwater, and groundwater lowering. The groundwater lowering and quality impairment may cause tunnel failure, with consequences such as injury to humans, as well as reduced property and environmental values, potentially costing millions of dollars to sponsors of the project. Depending on the nature of the contaminants and level of hydraulic connection of bedrock fracture along the length of tunnel, the contaminant transport may reduce structural strength of the tunnel due to corrosive action of contaminants such as acid drainage. The groundwater lowering can lead to varying degrees of ground settlement, posing threat of tunnel collapse. The management of hydrogeological risk includes:detection of potential pathways for contaminants into and around the tunnel,identification of factors responsible for the lowering of groundwater, and development of strategic measures to control groundwater lowering and contaminant transport. The paper presents an in-house hydrogeological risk management model named Vedanta-THRM (tunnel hydrogeological risk management). The model uses Risk Management Standard AS/NZS 4360:2004 (Standards Australia, 2004), Pressure State Response framework developed by Organisation of Economic Cooperation and Development, and Interaction Matrices. The Vedanta-THRM identifies important characteristics, processes and events of potential hydrogeological risk and develops control measures for managing hydrogeological risk throughout the life cycle of the project. The Vedanta-THRM was applied for a project in the early stages of planning and found to be useful in assessing, evaluating and reducing the hydrogeological risk in a managed approach that potentially increased the performance of the project. The application results also provided management options for use by project sponsors and insurance industry, which included tunnel risk financing options and options for equity investors to choose among various returns under different tunnel credit ratings.

Jan 1, 2008

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By Rogério Vicentini

O objetivo deste trabalho foi desenvolver um suporte cerâmico apropriado para a soldagem unilateral de liga de alumínio, utilizando a cordierita, uma vítria cerâmica constituída de óxidos. Trata-se de uma proposta tecnológica que viabiliza a produtividade da operação de soldagem, mantendo-se inalterada a qualidade da junta soldada ampliando os conhecimentos relacionados aos suportes cerâmicos focando a redução dos custos de fabricação.A soldagem unilateral com este tipo de suporte de solda foi executada em chapas de alumínio com arame de solda de alumínio 4043 pelo processo Gas Metal Arc Welding (GMAW). A eficiência do suporte cerâmico em suportar o metal de solda líquido foi verificada durante a soldagem do passe de raiz. Várias soldas foram executadas em chapas com espessura de 6,35mm para testar a eficiência do suporte. Parâmetros e variáveis do processo foram estudadas: a abertura de raiz, a tensão, a corrente e a energia de soldagem. Os resultados mostraram que o suporte foi eficiente para suportar a poça de solda líquida. Foi possível estimar uma faixa de operação do processo, com abertura de raiz de 2,0 a 6,0 mm e a energia de soldagem calculada ficou entre 0,62 e 1,46 kJ/mm. A soldagem foi realizada com mecanismo para facilitar a saída do arame de alumínio (tocha Push-Pull) sendo soldado puxando, da esquerda para direita, com pequena oscilação lateral em relação ao cordão de solda. As macrografias das juntas soldadas, além de revelar boa penetração lateral (entre 2 a 4,5mm) e reforço de solda com até 2,1mm de altura, pôde revelar ausência de descontinuidades como: trincas, falta de fusão, inclusão de escórias e porosidades.

Aug 16, 2017

By W M. Gilchrist

This paper gives an estimation of the future requirements of the western world in relation to energy re-sources. It then goes on to outline the role that atomic power -with its basic raw material, uranium -will play in supplying these energy requirements. Canada's position in this picture is covered, and some interesting forecasts are made. Introduction I T is possible that the following remarks will appear to have more to do with power than uranium. However, to fully comprehend what is in store for the Canadian uranium mining industry, we must be able to estimate the potential requirement, and, to do this satisfactorily, a thorough understanding of the circumstances that will give rise to that demand is necessary. The growing need for electrical energy will play by far the major role, as large tonnages of uranium will be required for its generation. The nuclear weapon has, up to the present, comprised the major market for uranium.

Jan 1, 1964

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963