Search Documents

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

By E. S. Moore

In the townships of Genoa and Marion, Subdury Mining Division, Ontario, there is a group of twenty-three mining claims known as the Jefferson claims. They are controlled by the Jefferson Mining Corporation and they were staked in 1908 by W. E. Smith, formerly of Sudbury, Ontario, and now of Smith & Reitz, a law firm of Minneapolis, Minnesota. These claims were staked for iron ore and in 1910 about 4000 feet of diamond-drilling was done on them. During the drilling operations galena and sphalerite ~were found in the iron formation in cores from holes, Nos. 2 and 3, claim W. D. 717, Genoa township. This discovery lead to a search for galena and sphalerite in the vicinity and a streak of rock containing these minerals was found in the iron formation a short distance to the east of. the drill holes. A shaft was sunk on this outcrop in 1912 to a depth of 8 feet and bottomed in an attractive lens of galena. Stripping revealed other small exposures of galena and sphalerite in the iron formation.

Jan 1, 1926

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550°°F,) caused excessive grain growth and warpage, Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F,). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in, thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

Residential and commercial plumbers in the United States were introduced to Viega?s copper press technology in 1999. In short, the technology allows plumbers and installers to join copper pipe securely in four to seven seconds on pipe sizes of 1.2 to 10 cm (0.5 to 4 in.) by pressing the connections with specialized tools and fittings rather than through sodering or welding. The water- and air-tight technology, first introduced in Germany in 1989, includes three different sealing elements, a variety of materials and a selection of configurations. By eliminating the need to thread or solder pipe, connections and repairs can be made quickly and securely. Installations are also much quicker and as secure as traditional methods.

Jan 1, 2012

By H von Blottnitz, J L. Broadhurst

Eco-efficiency has been proposed by the World Business Council on Sustainable Development as an environmental performance indicator framework that contributes to sustainability by assisting corporate decision makers improve the environmental performance of their operations and processes, while also extracting additional economic value. Given that the recent engagement of the minerals industry with sustainability has highlighted the need for requisite tools and methodologies, it is therefore of interest to assess whether eco-efficiency indicators can drive sustainability performance improvement during process design within the minerals industry. Previous work indicates that the choice of sustainability performance indicators to be used for decision making needs to be governed by the decision context; ie the performance indicators need to be fit-for-purpose. Here, the strengths and weaknesses of eco-efficiency indicators are analysed using case studies. First, a more rigorous definition of eco-efficiency indicators for the minerals industry is proposed based on indicators currently offered in the literature. Two case studies are then selected to reflect typical decision situations encountered within minerals process design. For each case study, eco-efficiency indicators are computed and are compared to more traditional graphical representations of the economic and environmental performance of process design alternatives considered. The sensitivity of these indicators to various process design parameters is also investigated. Results confirm that the meaningful application of eco-efficiency indicators is strongly dependent on the decision context in which the process data is generated. Results also show that eco-efficiency indicators can be related to technical process design parameters to allow for richer communication of performance information for various decision trade-offs; however, in some cases, graphical approaches that provide more insights into the environmental-financial trade-offs should be preferred. The research thus contributes to guiding the selection of the appropriate tools for more environmentally sustainable design of minerals beneficiation processes.

Jan 1, 2009

By G. Akdogan, T. P. Kekana, Q. G. Reynolds

The DC arc plasma gasifier concept is currently under development at Mintek for testing the feasibility of producing syngas from waste coal fines and dry steam. The technology is intended for the valorisation of low-grade discard coals into market-quality syngas, which may then be used for largescale electrical power generation to address current grid supply challenges in South Africa. Other potential applications include feedstock for petro-chemical plants, fuel for transportation vehicles, domestic and industrial heating, and others. The proposed concept of a DC arc plasma gasifier was developed based on a plasma torch, metallurgical-based and entrained flow coal gasifiers. The principles of design and operation of the proposed gasifier are based on the concept of the Westinghouse Plasma Corporation (WPC) gasifier where the torches are substituted by graphite electrodes from which electric arc plasmas are generated. The DC section of the gasifier will be designed considering Mintek’s experience in the sealing of the furnace as carried out in the Mintek Thermal Magnesium Process. As part of the building blocks of a full conceptual design, the feasibility of the DC arc plasma gasifier was investigated through testing and modelling of its critical elements as proof of concept. The main activities of this work included pilot scale evaluation of the arc behaviour in the presence of dry steam, modelling of the temperature distribution within the reactor and explosibility studies on three different coal dust samples. Keywords: DC arc plasma gasifier, explosibility index, lower explosion limit, minimum ignition energy

Jan 1, 2020

By Thomas Prietl

The use of gas stirring systems through the furnace bottom is common for anode and holding furnaces in the copper industry The first implementation of a gas stirring COP KIN® system in a Peirce-Smith converter was performed at the New Boliden smelter, Rönnskar, Sweden. In addition to other benefits, a decrease in process time and a decrease of the oxygen content in the blister copper were observed. To determine the effects of the gas stirring system and the process endpoint, an optical production control ?Semtech OPC system? was used. The light emission of the converter flame as an optical process parameter provides qualitative on-line process information, and is also used for endpoint determination of the slag making process, on-line control of iron content in white metal, quality control of slag etc. The results, benefits and risks of using the COP KIN® and OPC system for a Peirce-Smith converter are reported.

Jan 1, 2005

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

By E. Onal, C. Craddock, A. Chapman, M. R. Endsley

ABSTRACT Mining equipment operators must interpret and respond to complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge to effective decision-making and information exploitation. Incidents attributed to human error that compromise safety and result in loss of revenue, or even life, are often the result of system designs that overload human cognitive capabilities. This paper defines SA as it relates to the operation of mining equipment and describes the design and preliminary evaluation of a new electric shovel operator user interfa

Jan 1, 2013

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By Anderson Ayres Bittencourt

O monitoramento de sistemas e ativos de automação sempre existiu de forma rudimentar e descentralizada. A análise desses dados tanto quanto sua obtenção é um desafio para as empresas atuais. Foi a partir deste princípio que nosso projeto foi desenvolvido.Este trabalho tem como objetivo demonstrar a solução de Monitoramento online e preditivo implementada na ArcelorMittal Aços Planos da América do Sul, onde desde o início de sua implementação pudemos capturar benefícios operacionais, melhoria dos processos, otimização, eliminação e/ou diminuição de indisponibilidade de plantas, entre diversos outros retornos que serão apresentados.

Oct 30, 2017

By Maurice Bottiau

The recent evolution of the piling market clearly shows a growing demand for screw piles with soil displacement. The recently developed Omega Screw pile ful-fill these new expectations, combining the advantages of vibration-free systems and the behaviour of a displacement pile. The paper describes recent experience and new applications with this very promissing pile. Full-scale load tests were carried out in different countries as U.K. or Sweden. A very attractive and innovative piled embankment is also described, using geogrids in order to transfer the loads from the superstructure to non-reinforced Omega-piles.

Jan 1, 1996

By A. A. Dor

Recent developments in the design of concentration plants have reflected the increased recognition that has been given to the economic and metallurgical advantages of autogenous grinding. This has manifested itself in the increasing adoption of primary auto genous grinding in iron ore 'beneficiation plants in North America. Table 1 lists eleven major iron ore beneficiation plants which have either been put in operation since 1961 or are under construction at present. Seven out of these eleven plants have adopted primary autogenous grinding. Four of them have coarse grinding mills (8 to 14 mesh) and three have fine grinding primary circuits (48 to 65 mesh). Their nominal capacity totals 26. 2 million ltpy of concentrates or pellets, representing very nearly 75% of the aggregate capacity 135. 3 million ltpy) of the eleven concentrators listed. For a long time there was a tendency to consider that primary autogenous grinding was only applicable to suitable coarse grained ores, However, extensive testing of a very wide variety of ores, and actual operating performance in several commercial plants, seem to have established beyond reasonable doubt, that the majority of mineral ores which the beneficiation engineer may be called upon to process can be ground autogenously. The basis for the selection of autogenous or conventional grinding mills, becomes principally economic and depends on the liberation characteristics of the ores under consideration and their relative hardness and grindability.

Jan 1, 1965

By Lloyd A. Morley

The primary goal of this research report is to discuss safety considerations involved in the use of lead-acid batteries for traction purposes in underground coal mines. In order to arrive at the objective, the topic of battery safety has been divided into two specific areas. The first deals with the fact that batteries emit hydrogen gas during and after the charge cycle. Hydrogen gas can be the source of dangerous explosions or mine fires. The second major topic deals with the electrical nature of the battery and battery-charging systems, which also provides a source of mine fires as well as electrocution hazards. In addition to the discussion on battery safety, a literature review has been undertaken to acquaint the reader with some basic concepts inherent to the battery usage process. The result of this research is a set of design specifications and procedural recommendations directed at improving the safety factors inherent in any underground battery usage scheme.

Jan 1, 1977

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922