Search Documents

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

By H. Maleki, B. Jaramillo

La importancia de los diseños de pilares de acceso y de barrera, para el control del estrés y la sismicidad se demuestra utilizando datos geotécnicos y el monitoreo del estrés en tres estudios de casos. Los esfuerzos para eliminar los pilares de barrera fracasan en el primer estudio, mientras que una barrera de tamaño marginal contribuye a un evento sísmico de 4.2 en la segunda mina estudiada, la cual se ubica a una profundidad de 760 m. Por el contrario, la efectividad de un pilar de barrera de 150 m de ancho se muestra en el tercer caso, en las condiciones litológicas rígidas que caracterizan a Utah. El estudio confirma una reducción notable en el número de eventos por kilómetro (un factor de 4 a 8), en comparación con el distrito minero inicial en el que se usa la extracción de carbón por el método de pared larga de lado a lado (Long Wall).

Mar 30, 2020

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

By Brian Hart, Zhe Chen, Liuyin Xia, Mana Pourdasht, Stamen Dimov

"Gold losses related to carbonaceous matter (CM) during processing are a significant problem in the gold processing industry. Inherent CM in gold ores can behave similarly to activated carbon in its ability to adsorb gold cyanide. This phenomenon is termed preg-robbing as the surface adsorbed gold cannot, for the most part, be recovered. Research has identified that gold adsorption by inherent CM is linked to the specific surface area, pore structure, degree of C disorder and surface functional groups. One of the strategies to inhibit CM preg-robbing prior to leaching is a chemical oxidation; a process linked to modification of the surface functionality. In this study, the variability in gold cyanide adsorption due to oxidation with different reagents has been investigated. Variability in gold cyanide adsorption by CM is examined in relation to structural and surface modifications using TOF-SIMS, XPS and Raman spectroscopy.INTRODUCTION A major obstacle for effective gold recovery during carbon in leach (CIL) or carbon in pulp (CIP) processes carbonaceous gold ores is the presence of carbonaceous matter (c-matter) which has the ability to adsorb, or preg-rob gold from the cyanide leach solution. It can be responsible for poor recoveries as the carbonaceous materials (CMs) within the ore competes with activated carbon used during the leaching and adsorption phase of processing (Cay, 2014). Preg-robbing capacity can vary significantly with mild preg-robbing ores showing absorption capacities of less than 1 g Au/t ore, while severe preg-robbing ores may have CM with the capacity to preg-rob more than 500 g Au/t ore (Dunne, 2007). Research by a number of groups have shown that the degree of C disorder has some influence on the ability of the carbonaceous material to adsorb Au(CN)2- (Miller et al, 2005, Helm et al, 2009, Hart et al, 2010). It is also apparent the adsorption characteristics of carbonaceous material is affected by changes in surface chemistry (Dimov, 2016). Various treatment including; flotation to remove the carbonaceous material (Wills, 2010), addition of surface blinding agents (for example kerosene) to passivate or blanket the carbon surfaces (Dimov, 2016), addition of strong adsorbents (eg. activated carbon or resin) to compete with the carbonaceous material and passivation or surface coating by oxidation (pressure, roasting, chlorination and biological oxidation), have been employed prior to leaching in an attempt to minimize the gold losses (Dunne, 2013)."

Jan 1, 2017

By W. C. Hellyer

In an autogenous grinding circuit in which feed at approximately nine inches top size is reduced to a size suitable for subsequent processing, the build- up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge. 9, (1) The buildup of a "critical size" fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large diameter steel balls to the grinding charge. This has certain disadvantages, such as; (i) an increase in mill liner wear; (ii) wear on the steel balls, and; (iii) some loss in flexibility in grinding circuit operations resulting from difficulties in removing the steel balls by means other than by grinding out.

Jan 1, 1970

By Alessandra Labrin, Gloria Guevara, Dulce Trujillo

El presente estudio busca demostrar que la aplicación del método del Precio Comparable No Controlado (PCNC), tal como se encuentra estipulado en el Artículo 113-A1 del Capítulo XIX del Reglamento de la Ley del Impuesto a la Renta, en lo que respecto los precios de transferencia, es inflexible para analizar las operaciones de venta de concentrados de minerales a empresas vinculadas y domiciliadas en países o territorios no cooperantes o de baja o nula imposición. Usando un modelo de regresión lineal, se estima una ecuación que permite medir el impacto de cada componente de la fórmula del precio de venta del concentrado sobre el precio final. Los resultados sugieren que el costo de tratamiento (o maquila) es el componente que tiene el impacto más significativo sobre el precio final.

Sep 30, 2022

By Francisco Sotillo

El artículo da cuenta de una investigación orientada a demostrar los beneficios del mecanismo de conminución en una cama de partículas, como ocurre en los rodillos de molienda de alta presión (HPGR) o molinos de rodillos de alta presión (HPRM). Se ha investigado el uso de los HPGR de laboratorio para mejorar la eficiencia de separación de los minerales con alto contenido de dolomita, ultra alto contenido de arcilla y alto contenido de arcilla (kaolinita) presentes en una mena de apatita en operaciones subsiguientes «aguas abajo» de beneficio de diferentes minerales de fosfato de origen sedimentario. La investigación incluye estudios de caracterización de minerales de fosfato dolomítico, datos del modelo físico aplicado por PerUsa EnviroMet, Inc. de HPGR para desarrollar información preliminar de conminución; y evaluaciones de HPGR de laboratorio para determinar los parámetros de chancado (velocidades de alimentación; velocidad y separación de los rodillos; torque, presión y energía aplicables).

Sep 30, 2020

By Dave J. Porter

Si bien, los proyectos son el camino para que una organización minera cumpla con su estrategia, la gran mayoría de su historial de cumplimientos son un fracaso puesto que el impacto del proyecto no es tan rico en sus etapas y las organizaciones mineras no pueden cumplir con su visión y estrategía. En ese sentido, el presente texto señala la importancia de una adecuada gestión de proyectos para que la organización minera cumpla con su estrategia. Así, la madurez de la gestión de proyectos es un indicador de éxito continuo y requiere de visión, compromiso en las etapas iniciales, ya que sus ganancias son difíciles de cuantificar.

Apr 1, 2012

By J. Mizera, J. Zdunek, K. J. Kurzydlowski, A. Dobkowska

This work concerns comparison of corrosion resistance of the aircraft aluminum alloy composed of Al - 2.3%Li - 0.1% Zr. The alloy was hot rolled (HR) from 13 mm to a thickness of 4 mm (e = 2.4) and 1 mm (e = 5.2). Corrosion resistance was investigated by Potentiodynamic Polarization Test. The investigation relied on exposure samples in two different corroding medium: 0.5 M NaCl solution and 0.01 M Na2SO4 solution with added 0.01% of Cl- at room temperature. Furthermore, the microstructure was analyzed using the optical microscope with polarized beam. The hardness was measured on lengthwise profile. It was stated that alloy after the largest deformation (equivalent total strain e = 5.2) is characterized by the best mechanical properties and the best corrosion resistance. The alloys in initial state and after deformation to 4 mm (e = 2.4) are characterized by worse corrosion resistance. It is associated with microstructure and density of dislocation in analyzing material.

Jan 1, 2015

By Howard L. Hartman

Pardon my audacity, but I feel that this is the solution, not just a solution. Further, I will be so bold as to maintain that this is the last-ditch, eleventh-hour chance for the mineral industry to solve its critical technical manpower shortage. I am not being facetious. I am convinced that there is only one solution--just as there is but one real cause of the problem. My conclusion 'is reinforced by countless talks of endless hours with people both in and out of the industry, with employers and employees, and with educators and students. While I claim no originality for the idea and have no pride of authorship, I am concerned that the industry hear and heed in time. It is quite unlikely that the mineral industry and the mineral engineering profession will willingly subscribe to my thesis or gladly buy my proposal. I am convinced, however, that it is the only course of action open to us, and the only course of action which will succeed.

Jan 1, 1967

Throughout history, many of the world's achievements, conflicts and problems can be traced to the demand for minerals. With the rapid expansion of our industrialised society in recent years the demand for minerals has grown to such an extent that uncertainties about availability and cost have arisen, especially in the case of energy minerals.Minerals have acquired a new dimension for governments as the availability of these resources is interwoven with the ability of governments to achieve their developmental goals on national and international levels. Accordingly, the supply of minerals will increasingly be affected by social and political factors.

Jan 1, 1986

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By G. L. Gates

The waters used to waterflood the Wilmington oilfield were studied by the Bureau of Mines, in cooperation with the city of Long Beach, Calif. Increases in the pressure of the injection wells indicated that they were being plugged by materials suspended in the waters. This study was made to identify the suspended materials, determine their origin, and find methods of preventing their formation. The suspended oil-coated materials were iron sulfide, barium sulfate, calcium carbonate, clay, and sand (or silica). Results indicated that the sulfide, which was as high as 90 milligrams per liter, was the product of sulfate-reducing bacteria. The injection of ocean water increased the sulfate content of the waters in the petroleum reservoirs from 3 to 250 milligrams per liter, thereby furnishing sulfate for growth of the bacteria. The waters were supersaturated with barium sulfate. Laboratory tests showed that sulfide could be removed from the waters by adding iron at a cost of 1 to 2 mills per barrel. The solubility of iron sulfide and calcium orthophosphate in the injection waters was also determined.

Jan 1, 1975

By Luciano Lellis Miranda

Este trabalho apresenta os principais conceitos de Indústria 4.0 e discute os benefícios do emprego de alguns de seus mecanismos na construção de um sistema integrado de gestão de energia, em especial a utilização das tecnologias de big data (ou megadados, em português). A tese defendida neste trabalho – a possibilidade de se produzir grande valor a partir da abundância de dados de medição de consumo, de produção e de estados dos equipamentos, tipicamente encontrada em ambientes industriais – é demonstrada através do caso concreto da empresa Aperam South America, em sua planta de Timóteo, MG. Os resultados apresentados neste trabalho ilustram, qualitativamente, os potenciais retornos apurados no desenvolvimento de um sistema com as características descritas.

Aug 17, 2017

By Manuela Arend Prediger

Este trabalho tem como objetivo investigar, através da Espectroscopia UV-Vis, os diferentes estados de oxidação da Polianilina (PAni) obtida pela síntese química, através da reação da anilina em meio ácido e persulfato de amônio como agente oxidante, sob agitação constante e baixa temperatura. A caracterização da condutividade elétrica foi determinada através da técnica de medidas de 4 pontas. Foi possível verificar a obtenção de um polímero com características condutoras, através da observação, nos Espectros UV-Vis, dos picos que caracterizam o sal esmeraldina, sendo este o estado de oxidação da PAni que apresenta propriedades condutoras. Além disso, conseguiu-se obter valores de condutividade elétrica relevantes para confirmar a obtenção da PAni condutora.

Aug 17, 2017

By Bradley S. Van Gosen, Anjana K. Shah, George M. Bedinger, Donald I. Bleiwas, Karl J. Ellefsen

"Ancient and modern coastal deposits of heavy mineral sands (HMS) are the principal source of several heavy industrial minerals, with mining and processing operations on every continent except Antarctica. For example, HMS deposits are the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, obtained from the minerals ilmenite (Fe2+TiO3), rutile (TiO2) and leucoxene (an alteration product of ilmenite). HMS deposits are also the principal source of zircon (ZrSiO4), from which zirconium dioxide (ZrO2) is obtained for uses mostly in refractory products. Sometimes monazite [(Ce,La,Nd,Th) PO4] is recovered as a byproduct mineral, sought for its rare earth elements, and thorium (Ault and others, 2016; Sengupta and Van Gosen, 2016; Van Gosen and Tulsidas, 2016).HMS are sediments containing dense (heavy) minerals that accumulate with sand, silt and clay in coastal environments, locally forming economic concentrations of the heavy minerals (Fig. 1). Economic (mined) HMS deposits include Holocene sediments on modern coasts, such as examples in India and Brazil, as well as coastal deposits formed by transgressions and regressions of the seas during intervals in the Quaternary, Tertiary and Cretaceous, such as in Australia and the southeastern United States. Economic deposits typically contain heavy-mineral concentrations of at least two percent. Individual heavy minerals are commonly defined as minerals with a specific gravity greater than approximately 2.9 g/cm3. These minerals are generally resistant to chemical weathering and physical degradation and thus survive well in fluvial and coastal environments. Heavy minerals in coastal HMS deposits may include, in order of general abundance, ilmenite, leucoxene, rutile, magnetite, zircon, staurolite, kyanite, sillimanite, tourmaline, garnet, epidote, hornblende, spinel, iron oxides, sulfides, anatase, monazite, cassiterite and xenotime. Of these, ilmenite, leucoxene, rutile and zircon are the primary economic minerals. Garnet, monazite, cassiterite and xenotime are occasionally recovered as byproducts. The heavy minerals as a suite typically make up no more than 15 weight percent of a deposit and usually much less. Quartz and clay minerals form the bulk of the sediment. The geology of HMS deposits and examples of significant districts are summarized in Van Gosen and others (2014) and Hou and Keeling (2016)."

Oct 1, 2016