Search Documents

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By D. F. Malan, J. C. Esterhuyse

"Mining in the Carletonville area of the Witwatersrand Basin predates 1934. Owing to the depletion of higher grade ore, the current activities focus increasingly on the extraction of lower grade secondary reefs as well as remnant extraction. Of particular interest is multi-reef remnant extraction. Numerical modelling was conducted to investigate some rock engineering aspects of remnants being understoped on a secondary reef horizon. An analysis of the stress evolution in the middling between two reef horizons indicated that a zone of high major and low minor principal stress develops between the two reefs. This indicates a high risk of violent shear failure. Some pillars were nevertheless successfully understoped in the past and a study was conducted to better understand this phenomenon. An ’extended’ energy release rate concept introduced by Napier and Malan (2014) proved to be useful for investigating this problem. It was found that bedding planes and lithology appears to play a role in the stable dissipation of energy in multi-reef remnant geometries. The study indicated that the stope convergence and the various energy components are affected by the presence, position, and properties of a bedding plane. The energy solutions are complex and sometimes counterintuitive. Care should be exercised when modelling specific cases. The modelling was nevertheless valuable as it indicated that energy dissipated on weak layers may reduce the risk of violent failure in a multi-reef mining scenario. Additional work is required to investigate if crushing on the reef plane plays a prominent role when mining these remnants. IntroductionTo extend the lives of the Witwatersrand gold mines, work is being conducted to include a larger number of remnants and pillars in the reserve base of the mines. According to Jager and Ryder (1999), a remnant is an unmined block of ground surrounded by extensive mining. Remnants are typically left because of adverse or difficult mining conditions caused by geological structures, poor ground conditions, low grade, or rockburst damage (Durrheim, 1997). In contrast, pillars are typically the result of rock engineering designs to control energy release rates (ERR) and seismicity. During the early 1900s, remnants formed by the practice of scattered mining layouts had a significant effect on seismicity. Numerous task teams were appointed during this period. As the industry expanded, the severity of rockbursting increased and the research was formalized after the 1960s. Various recommendations were made and many of these are still used as best practice today (e.g. Jager and Ryder, 1999)."

Dec 1, 2018

By Fábio Yamada, Ruano Araujo, Marcelo Fugihara, Matheus Sousa Reis

A evolução internacional do mercado de alumínio requer capacidade das empresas de atender uma demanda crescente e para isso se faz necessária uma gestão logística eficiente. O presente trabalho tem como objetivo avaliar o fluxo de veículos em uma fábrica de processamento de alumínio através da simulação dinâmica de processos e tecnologia de modelagem. Com isto, propõe-se avaliar a gestão de recursos (equipamentos e operadores), capacidade de estoques, fluxos internos e movimentações de carga na fábrica; assim, pode-se avaliar a necessidade de novos investimentos nestes quesitos. A análise envolve o cenário atual bem como a demanda futura projetada com o acréscimo de um modal logístico anexo à fábrica, que aumentará o fluxo de produtos na empresa. Em síntese, este artigo relaciona-se com os temas: logística, modelagem matemática de processos e melhorias em produtividade.

Oct 1, 2019

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948

Although AustraliaÆs coal mining industry is currently experiencing a pleasing period of price relief, long-term trends toward lower real prices will surely continue. Higher price levels attract expansion by existing operators and market entrance by new operators. History clearly demonstrates the relentless long-term march toward ever lower real prices. Therefore, the need for economic returns applies constant pressure to improve productivity. To be sustained, high productivity requires a systematic response based on a solid understanding of critical productivity determinants. The most powerful determinant of productivity is now widely understood to be workplace culture. Culture largely comprises a combination of behaviours, symbols and attitudes. This paper will examine and review scienceÆs latest discoveries in human behaviour. It will provide a proven, practical framework for understanding behaviour and applying this knowledge. Significantly, it will highlight why conventional approaches toward improving productivity often provide disappointing economic returns. The modern understanding of behaviour factors will cover coal face operations. More importantly, because executive and managerial levels in coal mining have significantly greater impact on industry and mine productivity the paper will concentrate on leadership. Particular emphasis will be placed on use of modern systems and in particular use of what are by far the most powerful drivers of behaviours û measurement, analysis and reporting systems. The paper and presentation will show how conventional systems rooted in antiquated American legislation from the early 1900s stifle productivity improvement and drive suboptimal and even counterproductive behaviours. These commonly used systems will be compared with accurate and effective modern methods for assessing performance to improve productivity. These principles are proven in all industries and effective application in mining will be highlighted. Actual results will be used to demonstrate practical approaches successfully applied in both metal and coal mining in Australia and overseas.

Jan 1, 2005

By Willy Ank de Morais

O estaqueamento profundo é necessário para obter fundações firmes e confiáveis, mesmo em solos de baixa resistência. Após completar a soldagem entre dois perfis, através do uso de talas, que compõe uma estaca de uma fundação profunda, essa união é inserida, juntamente com o restante da viga, através de uma máquina de estaqueamento. Neste processo a região da emenda pode sofrer choque térmico devido à umidade presente no solo. Este trabalho visa demonstrar a viabilidade da imediata inserção (‘cravação’) no solo de juntas entre perfis de aço ASTM A572 Grau 50, efetuadas através da operação de soldagem com eletrodo revestido (E 7018), simulada através de uma condição de maior criticidade pelo processo de arame tubular.

Oct 30, 2017

By Mir Ahmad Mohammadi

Land uplift due to mine flooding has become a significant challenge with extensive historical mining activities, particularly in Germany’s Ruhr district. The cessation of coal mining operations has led to a gradual rise in groundwater levels, altering geotechnical and hydrological conditions and causing surface uplift. This study develops a system dynamics (SD) model to investigate the dynamic interactions of influential variables such as groundwater levels, total stress, porosity and permeability with land uplift over time. The model integrates causal loop diagrams (CLD) and stock flow diagrams (SFD) to comprehensively understand the system’s behavior. SFD illustrated that for a 10 percent increase in groundwater level, the land uplift increased by about +6 percent, and a rise of 200 percent in total stress caused an 18 percent increase in effective stress, which decreased the land uplift by about 20 percent. This study highlights the importance of dynamic modeling in informing land-use planning and mitigating the long-term impacts of land uplift after mine closures.

Mar 1, 2025

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By Michael J. Nicol

The teaching of courses in geology, mining and extractive metallurgy in Australian universities is undergoing significant change largely as a result of the initiative taken by the Minerals Council of Australia (MCA). This has resulted in a major program aimed at developing national under- and postgraduate courses in selected areas with the aim of making these available to a consortium of participating universities. Murdoch University, together with the A J Parker CRC for Hydrometallurgy has been commissioned to develop the course in hydrometallurgy. Progress in the development of this course will be discussed in terms of overall philosophy, content and mode of delivery. Aspects of the extension to a Web-based course will also be summarized. Murdoch University has also established a hydrometallurgical pilot plant on the campus and the results of the first continuous operation for several months using under- and postgraduate students as operators will be discussed from the point of view of practical training and providing an interface with the local industry.

Jan 1, 2002

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By Laura Pires Ribeiro Martins

Para a produção de peças e componentes automobilísticos, a utilização de ensaios não destrutivos é de grande importância, tanto para a detecção de defeitos como para a estimativa de propriedades físicas e mecânicas. Este estudo tem como objetivo avaliar dois métodos de ensaios não destrutivos (frequência de ressonância e ultrassom) através da determinação do módulo de elasticidade e do amortecimento de vibrações, em ferros fundidos vermiculares de classe FV 450. Estas técnicas também foram avaliadas para identificar a presença de microporosidades de contração na solidificação. Verificou-se que estas metodologias permitem estimar valores de módulo de elasticidade com bastante precisão, superior à obtida com ensaios de tração. Comprovou-se ainda que a capacidade de amortecimento de vibrações, avaliada pela taxa de atenuação da oscilação, é sensível à presença de interfaces na microestrutura do material, bem como à presença de pequenas porosidades.

Aug 16, 2017

By Angus W. Davis

The case of the P. G. E. railway is a peculiar one. Traversing, as it does, to a large extent, a mineralized country there are as yet no producing mines along its route although I am convinced that mines will be developed in the region tributary to the railway. The Fitzimmons group of claims, a copper property near Mons station, 37 miles from Squamish is now (unless recently relinquished) under bond to the Granby Company. On Cadwallader creek, in the upper Bridge river country, certain gold properties, referred to later, are being developed. Prospectors are fairly active in the Pemberton meadows area. There are also a large number in the Bridge river, Gun creek, and Whitewater districts. East of Marguerite station some development work is being prosecuted on some copper claims located there. In addition here and there throughout the entire route of the railway prospecting is being undertaken. At Hat creek, 15 miles from Pavilion station there is an enormous deposit of lignite. It is by no means certain that this coal can be profitably mined and hauled to the railway, but as a cheap fuel it offers possibilities in the recovery of by-products by destructive distillation. Logical procedure would ? indicate the expenditure of considerable money on development and, if results justify, the construction of a spur from the main line to the deposit.

Jan 1, 1925

By Paulo Ricardo Bastos de Queiroz

Após estudo realizado, verificou-se que a CSP - Companhia Siderúrgica do Pecém, possuía alta vulnerabilidade às oscilações de frequência, sejam elas oriundas de falhas nas unidades geradoras ou problemas nas linhas de transmissão que compõem o SIN (Sistema Interligado Nacional), onde tais perturbações poderiam provocar desde a parada total da planta a danos irreversíveis em equipamentos como motores síncronos. Com base nesse estudo, foi implantado um sistema automatizado e de rápida resposta capaz de diminuir ou eliminar todos os efeitos provocados por tais distúrbios, atuando de forma dinâmica e coordenada com o cenário energético ao qual a planta siderúrgica encontra-se no momento do evento. Dentre os ganhos apontados em estudo, destaca-se a confiabilidade de se ter um sistema de distribuição de energia em uma usina siderúrgica capaz de assegurar a continuidade do processo ou em piores casos proporcionar uma parada emergencial com total segurança.

Oct 30, 2017

By Natalie Chaves de Siqueira

Aços inoxidáveis austeníticos fundidos por centrifugação, da classe HP, são comumente utilizados na indústria de óleo e gás para a fabricação de tubos usados em fornos de reforma e pirólise. Essas ligas possuem uma elevada resistência à oxidação, elevada estabilidade térmica e elevada resistência à fluência em altas temperaturas, sendo esses requisitos necessários para aplicação nos fornos. Mudanças microestruturais, conhecidas como envelhecimento, podem ocorrer durante a operação, influenciado na resistência à fluência. Desta forma, a caracterização dos estados de envelhecimento de uma liga HP torna-se necessária para avaliar a sua vida remanescente. O objetivo deste estudo é caracterizar duas condições microestruturais de uma liga HP com a microscopia eletrônica de varredura e o ensaio não destrutivo de ultrassom. O processamento do sinal ultrassônico, utilizando a Transformada Rápida de Fourier (Fast Fourier Transform – FFT), foi realizado sobre o segundo eco de fundo do sinal ultrassônico, permitindo correlacionar a análise espectral do sinal com a microestrutura do aço HP. De acordo com a metodologia proposta, os dois estados de envelhecimento foram caracterizados através do processamento do sinal ultrassônico.

Oct 30, 2017

By Renato Affonso de Lima

As colunas utilizadas para a produção de hidrogênio em fornos de reforma a vapor são submetidas a temperaturas da ordem de 900°C. Dessa forma, os aços inoxidáveis austeníticos da classe HPNb se mostram adequados, devido ao endurecimento por precipitação de carbetos de cromo e de nióbio. Sob determinadas condições de serviço, os carbetos de nióbio podem se transformar em um siliceto conhecido como fase G. A interface desta fase com a matriz austenítica é citada na literatura como local preferencial para a nucleação de danos de fluência. Sendo assim a quantificação das fases presentes é importante para a avaliação do acúmulo de danos em serviço. Diante disso, a simulação termodinâmica computacional se mostra uma importante ferramenta, para a previsão das fases presentes. Técnicas como a analise quantitativa das fases presentes por meio de imagens são consolidadas, porém demandam amostras devidamente preparadas e um alto custo de equipamentos na execução destas análises. Isto posto, o objetivo do trabalho é comparar as simulações termodinâmicas computacionais com o resultado obtido por meio de análise quantitativa de imagens geradas por microscópio eletrônico de varredura.

Oct 30, 2017

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Refractory gold ore contains sulfide minerals like pyrite, chalcopyrite and sphalerite that are difficult to be directly leached by cyanidation or by lixiviants such as thiourea and halides. In such cases, it is necessary to perform oxidative pretreatment of the ore to oxidize the sulfide matrix, and gold particles can be exposed to the solution during the leaching process [1]. In recent years, hypochlorite and chloride solutions have been introduced as alternative materials for hydrometallurgical methods of gold extraction instead of cyanide solution [2]. A previous study by Hasab et al. [3] reported that the gold dissolution rate in hypochlorite solution was higher than in the cyanidation process, due to the presence of hypochlorous acid (HOCl) as a strong oxidizing agent. In a hypochlorite leaching system, the change in pH can influence the presence of oxidant species in the solution: the hypochlorite ion (OCl−) is stable in pH greater than 7.5, HOCl can be found in pH between 4.0 and 7.5, and aqueous chlorine (Cl2 (aq)) is the predominant oxidant when pH is below 4.0. As HOCl is the most effective oxidizing agent for gold extraction, pH should be maintained in the range of HOCl stability [4].

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986