Search Documents

An enhanced gravity concentrator was installed in conjunction with an intensive leach reactor at the Sadiola plant in Mali last year and commissioned in December 2007. There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every ten per cent of gold recovered by gravity, there was a corresponding 0.1 per cent to one per cent additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall four per cent gain in plant recovery. With total gold recovery of 12 per cent in the gravity section, grades are increased from 3.54 g/t in the gravity feed to an average of 2 600 g/t in the concentrator feed to the inline reactor. The recovery of gold in the inline reactor is in excess of 98.5 per cent. This paper discusses the background to the project, the laboratory test work prior to the equipment selection, the operational results of the system, as well as the benefi ts of the future application of high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.

Aug 1, 2010

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By K. V. Raj

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in open-pit mines is relatively new. Modeling the actual pit geometry of an open-pit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an open-pit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in open-pit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions, and turbulence modeling parameterization. An appropriate mesh selection is critical. A detail discussion of the meshing of the domain of an open-pit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (?-e), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an open pit and some of the approaches adopted to address these challenges.

Feb 27, 2013

By Arthur L. Murray

"While serving as surgeon with rescue car No 11 of the U. S. Bureau of Mines, the writer visited the principal metal-mining camps of Utah during the latter part of 1919. In visiting the mines, meeting and conversing with miners, and talking over the medical situation with physicians in the various camps, the number of cases of lead poisoning encountered was great enough to attract attention.With a view to procuring more definite information as to the number and distribution of cases of lead poisoning throughout the State, a study of the records of the State Board of Health was undertaken. Utah had no ordinance re¬quiring the reporting of occupational diseases, so it was not possible to secure data an cases A study of the mortality records by years gave the following results.:Year Deaths from lead poisoning.1910,11911,01912,21913,11914,61915,41916,11917,31918,11919,2These few deaths would seem to indicate a fairly low case rate, but when it is realized that lead poisoning is rarely an immediate cause of death and that the train of sequelae in this disease frequently leads to chronic involvemeets of the digestive, nervous, circulatory or genito-urinary systems, it is apparent that the number of deaths showing lead poisoning as the cause can not be taken as an index of the cases prevalent. The time elapsing between the presence of the active signs of lead poisoning and the terminal illness from pathologic conditions excited by lead absorption may be years, and the initial cause, lead poisoning, is frequently lost sight if entirely, hence the death certificate shows no evidence of the primary cause."

Aug 1, 1921

It is a great honour to address our Institute as President, but the choice of a suitable subject was not an easy one. In the past when the presidential address was given at an annual conference the subject usually related to the conference or industry concerned; more recently the subjects have been more philosophical and this is a distinct advantage to me.I appreciate that I am addressing an informed audience and I am sure' that you are well advised in many of the points that I hope to leave with you. Unlike the specialist who gets to know more and more about less and less and eventually knows everything about nothing, I am one of the group who gets to know less and less about more and more and eventually knows nothing about everything.I hope you will appreciate this point whilst you are listening to me.In recent years I have been closely associated with the problem that troubles most governments of our time: the competition of many groups of differing backgrounds for the land that is available to the nation.This is of particular interest to the industry with which we are concerned as it is of critical importance to the discovery and development of future reserves of minerals and metals. Part of my daily task is involved with the administration of legislation for mining operations and the conditions under which such operations may be undertaken, in implementing government policies relating to mining, and in designing and administering legislationdirected to safety and health in mines.Most of our members are involved in exploration or in day-to-day problems associated with the production of minerals or the management of companies in these pursuits and would be aware of many of the conflicting viewpoints on priorities.F. F. Espie in his presidential address of 1975 'On being a minority', made the point that our Institute found that the mining industry had a great communication 'Problem with the Australian people.I believe that this is one of our major problems.

Jan 1, 1977

Jan 1, 1988

By K. L. C. Gonçalves, V. K. Alves

"CVRD’s Department of Development and Technology – GETEK has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. This methodology has been applied in several prospective CVRD mining projects. It encompasses a procedure for variability analysis based on bench scale tests, pilot scale grinding and flotation tests and modeling and simulation for scaling up the industrial flowsheet.The bench scale tests include the determination of the Work Index, simplified DWT tests, rougher flotation and locked-cycle tests with samples that are representative of the ore body variability. After completion of these studies, continuous, pilot-scale flotation tests are carried out at a Mini Pilot Plant with drill core samples representative of different stages of the mine life. Finally, studies are carried out with large volume samples using a conventional grinding and flotation pilot plant. This sample is also used for liberation characterization, grinding kinetics, flotation kinetics and industrial circuit scale up. This methodology has been successfully employed in the development of CVRD’s new mining projectINTRODUCTIONCVRD has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. The definition of the processing route and the sizing and scale up of the processing system are some of the products generated during the pre-feasibility of a greenfield project. This paper is focused on the scale up of grinding and flotation circuits, operations known to be of the most importance in a mineral processing plant.The methodology for the definition of the flotation and grinding circuits is divided in the following stages: bench scale ore variability studies, pilot plant operation and modeling followed by simulation. The product of this work is a calibrated simulator that can be utilized for plant operation as well as mine planning, looking to achieve optimal operational conditions.The current models used for scale up of the grinding circuits are aimed at the generating information about the size distribution of the circuit product. However, it is well known that the liberation state of these products may be of critical importance for the performance of the concentration processes downstream. Nevertheless, CVRD has been developing a methodology for liberation kinetics during grinding, aimed at optimizing grinding circuit throughput together with downstream flotation recovery."

Jan 1, 2006

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By L. A. Cramer

South African platinum mines produce the world?s majority of platinum metal that is used in autocatalysts and jewellery. As the platinum market is forecast to grow at healthy rates into the future, the South African producers, Anglo Platinum, Impala, Lonmin and Northam, are planning to expand in the next decade. Furthermore, a number of smaller producers who are accessing other mineral rights are entering the buoyant market. The South African platinum mines have traditionally exploited the Merensky Reef of the Bushveld Igneous Complex (BIC); however, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the orebodies at deeper levels. In the past decade all of the producers have begun to mine the less attractive UG2 reef because of its cheaper mining costs. This UG2 reef contains significant quantities of chromite with typically a chrome-to-iron (Cr/Fe) ratio of 1.35. UG2 ores can contain between 10 and 25% Cr2O3dependingupon the reef width and the selected mining method. It is relatively cheap and easy to extract a portion of the chromite from a platinum concentrator tailings stream at a grade of between 40?42% Cr2O3. However, it is only in recent years that some ferrochrome producers have begun to source some of their chromite from the tailings of platinum producers. South Africa is also the world?s largest single producer of ferrochrome and supplies much of the world?s stainless steel producers and thus the growing market for their product. As the traditional sources of high Cr/Fe ratio ores have been depleted at the shallow economic depths and thus have become more expensive sources of chromite, technical developments have improved the ability to use fine chromite economically to make acceptable grades of ferrochrome. Thus UG2 fines are now becoming possible cheap sources of acceptable feed to the ferrochrome industry. The abundance of feedstock for ferrochrome production and the lessening dependence on mined material will impact upon the structure of the ferrochrome business in South Africa. With continued platinum mining from UG2 reefs, South Africa is set to remain highly competitive in the world?s ferrochrome/stainless steel industry.

Jan 1, 2004

By A. J. Kesterton

MORE than 90 pct of the total tonnage of ingots made at Abbey Melting Shop is for steel sheet to specifications ranging between 0.055 and 0.07 pct maximum carbon. Since the rate of carbon elimination in the open hearth declines considerably as the carbon approaches these low levels, the use of oxygen for this purpose constituted a profitable field for development, particularly to increase ingot output. Development Several experiments were carried out initially in which water-cooled guns, originally of all-steel construction and later with fabricated copper heads, were introduced manually through a hole in the back wall of one of the 225 net ton furnaces, the oxygen being delivered about 4 to 6 in. above the slag. Successful blows were obtained, but manipulation of the gun was cumbersome. Application through the charging doors by means of bare steel lances was considered but rejected, because much of the scrap was light, necessitating a large number of buggies per charge, and consequent long occupation of the track in front of the furnaces by buggies. To construct an efficient mechanism it was decided to experiment with the introduction of the gun through a hole in the roof. This was eventually successfully achieved, with the following advantages. 1) The actual mechanism required is simplified, and can easily be remotely controlled. 2) No large steel framework projects out over the back platform, possibly interfering with tapping, and there is no danger of damage by casting cranes. 3) The railway track in front of the furnaces is left entirely clear for the passage of scrap buggies, eliminating interference with adjacent furnaces charging. 4) As compared with the use of bare steel lances, a water-cooled jet eliminates the manpower required to handle, control and change the bare pipes. 5) A jet through the roof can be situated over the center of the bath so that, whatever the direc-

Jan 1, 1958

An integrated palynological and sedimentological investigation of four wells from the eastern margin of the Gippsland Basin has resulted in a scheme for classification of palynofacies in this area. Thirteen different palynofacies assemblages are recognised and assigned to particular environments based on the enclosing sediments, which range from alluvial, through coastal barrier to continental shelf environments. Close correlation is observed between the interpreted energy regime of the palynofacies assemblage, and that of the enclosing sediments. Assemblages characterised as reworking surfaces can be correlated with unconformity producing events (ie tectonic activity associated with the opening of the Tasman Sea), and some of the minor eustatic sea level Changes.

Jan 1, 1992

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Peter White

A bridge reconstruction project involved driving pipe piles for the new foundations. Disturbances within soil layers at depth caused sinkholes to open up within the construction site. After a near fatal accident, the pile driving installations were suspended. The solution involved ground im­provement through cement grouting with sleeve pipes and special grout additives to minimize migration of cement grout.

Jan 1, 1997

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

Recently discovered Carboniferous bentonites are variable in charadeI and thickness, but being altered aeolian, ash-fall tuffs, they are probably extensive. Most are the Ca-montmorillonite type without the natural swelling characteristics of the Wyoming deposits, but their situation, thickness, and response to beneficiation through cation exchange may give them some potential as sources of future economic deposits.INTRODUCTIONLoughnan and See (1959) gave an account of bentonites and fuller's earth deposits of New South Wales. The most likely potential industrial sources were those occurring in the uppermost formations of the Newcastle and Singleton Coal Measures (Permian) in the Hunter Valley and deposited during epochs not marked by strong contemporary vulcanicity.One feature of the record of known occurrences at that time was the absence of bentonites from the thick volcanic sequences of the Carboniferous, but since this paper appeared, many bentonite beds have been discovered by the writer in the Carboniferous facies formerly known as the "Kuttung Series".The purpose of this contribution is to report briefly on the occurrence, genesis, mineralogy, and economic potential of these deposits which augment possible sources of bentonite near major industrial centres on the eastern seaboard.The potential world demand for bentonite would increase markedly with the trend to pelletization in the steel industry, if its use in this field became more general. More detailed mineralogical studies will be presented in later publications.STRATIGRAPHIC DISTRIBUTIONBentonite occurs at irregular intervals throughout a thick sequence of dominantly continental, plant bearing strata...

Jan 1, 1965

By S Hapugoda, J R. Manuel, M J. Peterson

Microindentation testing using the square–pyramid–shaped Vickers indenter is a well-established technique to determine the microhardness of minerals and materials. However there is a paucity of published microhardness data from Fe ore samples. It is acknowledged that an iron ore’s particle mineralogy and texture is critical to its processing properties, and it is therefore considered that the microhardness of different mineralogical/textural types may also relate to these properties. Mineral microhardness potentially provides inputs to the modelling of breakage characteristics during comminution, as well as the relationship between mineral chemistry and microhardness, and mineral microporosity and microhardness. Microhardness can be determined as single crystal microhardness, for more coarsely microcrystalline samples, or as ‘aggregate microhardness’ for cryptocrystalline or finely microcrystalline samples.Variations in the texture and mineral chemistry of common Fe ore minerals (eg martite and microplaty hematite, ochreous and vitreous goethite etc) are well established and this study provides microhardness data on different textural forms of Fe (oxyhydr)oxides from a variety of different Fe ore deposits. The data indicated that in general, the mineral grain size, microporosity and texture were the main influences on Fe (oxyhydr)oxide microhardness. There were no apparent systematic variations between microhardness and minor element mineral chemistry, with the possible exception of Al content in goethite (for goethites with Al content >0.5 wt per cent), and for goethite total element contents >90 wt per cent (determined by electron probe microanalysis, EPMA). Higher Al concentrations and lower total element concentrations in goethite EPMA analyses correlated with lower goethite microhardness. Microporosity and grain size were more important than texture to hematite microhardness. Different textural forms of dense hematite (eg martite, recrystallised interlocking hematite and specular hematite) with similar grain size exhibited comparable microhardness. Microhardness values for hematite and hydrohematite with little or no evident microporosity were also similar, whereas more porous forms of martite, microplaty hematite or hydrohematite exhibited lower microhardness.CITATION:Peterson, M J, Manuel, J R and Hapugoda, S, 2017. Microhardness testing of hematite-goethite Fe ores – implications for their textural characterisation and geometallurgy, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017