Search Documents

By H. Yilmaz

A testing method for assessing the shear-bond strength of thin spray-on liner (TSL) on rock substrate was developed at Wits University Rock Mechanics Laboratories. The gap between a 20 mm thick steel ring and a rock core is filled with TSL along the depth of the ring. After the curing of the TSL for a predetermined period, the sample is placed on a base, which offers support to the steel ring and the TSL but not to the rock core. A compressive load is applied on the rock core displacing the core on TSL contact and punching it towards the void in the support base. Shear-bond strengths for different TSL products as well as shotcrete were measured. This paper describes the test set-up and points out the important aspects and procedures during sample preparation and test execution. The test results are also presented and discussed.

Jan 1, 2007

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By D. J. R. Ras

A sub-level open stoping method is being used to mine the massive deposits at TARGET Gold Mine which uses cemented tailings to backfill the stopes. This requires the construction of bulkheads to contain the freshly placed backfill, capable of resisting the hydraulic pressure imposed by filling. The bulkheads must contain an 8 metre head of backfill slurry within 48 hours and withstand the force exerted by a 35 metre load of consolidated fill at a maximum estimated fill relative density of 1.9. After a variety of methods of construction were evaluated, it was decided to construct the bulkheads using the low density, fast-setting foamed cement-based product TEKSEAL HS manufactured by MINOVA RSA. The cement foam is contained between low-cost steel and fabric brattices which are easy to construct, using a method specially developed for the TARGET bulkheads. The paper will describe the design, trialling and construction of the bulkheads, and results obtained to date.

May 1, 2007

By A. Hammel

This paper summarizes indigenous mining methods used to collectmetal ores in pre-colonial southern Africa, south of 15°S. These methods, for the purposes of discussion, are divided into sections inorder of increasing organizational complexity, from scavenging,which only required basic equipment and a relatively minimal division of labour, to underground mines, which necessitated complex planning to overcome obstacles such as the need for illumination and ventilation. Examples concerning the pre-colonial exploitation of iron, copper, tin, and gold have been taken from the archaeological literature. This review paper provides an introduction to the technology that was available to and used by miners in the past, illuminates some of the factors limiting their operations, and supports the claim to the indigenous nature of this activity

Jan 1, 2000

By B. Kenny

The aim of this paper is to provide an overview of existing forms of subcontracting in the South African mining industry. A descriptive framework is developed to understand different subcontracting arrangements. We argue that, in order to do so, it is important to distinguish between labour broking and gang subcontracting. Data resulting from a research project (including an analysis of historical sources, interviews with contractors and focus group interviews with mineworkers) is presented to highlight the implications of changing formations of subcontracting for the South African mining industry in the late 1990s. Apart from the subcontracting of ?traditional? functions, such as shaft sinking, access development, catering and hostel maintenance, contractors are now used in ?core? mining activities. In some instances, whole shafts are ?outsourced? to outside agencies. It is argued that certain of the subcontracting arrangements have serious implications for the ability of the mining industry to improve health and safety standards. Some of the practices can potentially result in conflict between different categories of workers, and, as a result, instability in the industry.

Jan 1, 1999

By S. Dessureault

Computer Integrated Mining (CIMG) is a process of using computer networks to transform islands of enabling technologies into a highly interconnected mining system. CIMG involves the integration of advanced technologies at various levels in the mine business to achieve higher flexibility, better quality of processes and control, and improved profitability. Justifying the benefits of CIMG are difficult as many of the advantages are derived from improved flexibility, quality, and control. Justification is based on the evaluation of the benefits to be gained, compared to the required capital investment. Management tools used in mining are currently inadequate in assessing the value of advanced technology whose benefits are primarily qualitative. A key aspect of successful implementation is management acceptance, which has to be won through the capability to justify the technology?s financial costs and the true value of all of its benefits. The manufacturing industry faced similar justification difficulties when adopting advanced technology in factories. A significant amount of funding and research was invested in developing management strategies and approaches to justification. Many of the problems that faced the transformation of the manufacturing industry in the late Eighties and early Nineties are now facing mining. The solutions derived for manufacturing may help mining in its transition to an increased reliance on integration technology. Reviewing the industrial history of computer integrated manufacturing identifies several tools and strategic frameworks that can be adapted for mining. Keywords: Computer integrated mining, justification techniques, CIM, information technology.

Jan 1, 2004

By Stanford O. Grodd

The Sanford Lake district encompasses an area covering 24 square miles in the central Adirondack Mountains of northern New York State. Discovery of the titaniferous magnetite deposits dates back to 1826. Several attempts to exploit the ores for iron prior to 1942 proved uneconomical because of difficulties with the associated titanium, lack of transportation facilities, and the isolated location. Since 1942, the National Lead Company has produced ilmenite concentrates for the titanium pigment industry, and a magnetite by-product used in the steel and refractory industries. Rocks of the area are Precambrian in age and of igneous origin. The area has a history of erosion, deformation, and metamorphism, subsidence, and finally uplift and glaciation. The resulting topography is extremely rough with drainage patterns controlled by a combination of fault patterns and glacial modifications. The district is within the large anorthosite massif making up the central high peak area of the Adirondacks. All of the various lowsilica rock types associated with the massif are found within the boundaries of the district. These consist of both the Marcy and Whiteface types of anorthosite and of gabbroic anorthosite, gabbro, and different grades of titaniferous magnetite ores. All of the rocks contain the same minerals and differ only in their percentages of these consitituents. Gabbro, and ore associated with it, demonstrate flow structure as both have foliation and lineation. Anorthosite and its associated ores are massive and show very little primary structure. Minor pegmatites and diabase dikes provide evidence of remobilization in selected areas and of late intrusion as well. Faulting is prevalent and follows a regional pattern of major faults trending northeastsouthwest and of minor faults at nearly right angles to them. There are four mineralized areas where an economic grade of ore has been found. Three of these have both gabbroic-type ore and anorthositic-type ore. The fourth has only gabbroic ore. Ores are graded according to their TiO, content, and these range from 9.5 per cent to over 30.0 per cent TiO,. Ore bodies of both types are related to gabbro and conform to the configuration of the gabbro bodies within the anorthosite. At least three distinct theories of ore genesis have been expounded by different investigators. Others propose some variations of one or more of these. Although complete agreement probably never will be reached, it is certain that no one process of ore emplacement can explain the complicated picture as seen today. Further understanding of the ores and their origin will require detailed mapping, sampling, and mineralogical studies of the entire district, and then it may never be understood without qualification.

Jan 1, 1968

By S. Hunt, D. de Vries

Kansanshi Copper Smelter began operation in March 2015. The smelter features a single Isasmelt furnace for smelting, one 6-in-line electric furnace for matte-settling and slag-cleaning duties, four Peirce- Smith converters and two rotary anode furnaces. A 1,450 t/day oxygen plant and a 4,085 t/day sulphuric acid plant are included in the smelter operations. This paper gives an overview of the operational performance to date with summary data for each smelter section. Challenges such as an unforeseen refractory failure in the Isasmelt furnace in 2016 are discussed. Design improvements around the electric furnace are mentioned. Plans for potential future improvements are put into context. A consistent focus on operations, maintenance and continuous improvement has seen the smelter easily achieve its nameplate capacity of 1.2 million tonnes per annum of copper concentrate throughput. The smelter now operates consistently at a concentrate throughput rate of 1.38 million tonnes per annum of copper concentrate. INTRODUCTION The smelter was commissioned in March 2015. Design and commissioning of the smelter have been discussed by de Vries, Hunt, Hanschar and Louie (2016). The smelter rapidly ramped up to achieve nameplate production (1.2 million tonnes per year concentrate) and in 2018 operated consistently at the rate of 1.38 million tonnes per year concentrate. This paper presents major operational data for each section of the plant and describes significant events and improvements during the first four years of operation. The smelter flowsheet is shown in Figure 1.

Jan 1, 2019

By David Jurich, Ed Perko, Jacob Prezkuta

Numerous Colorado mountain tunnels that date to the late 1800s convey water to the farming and urban communities of the eastern Front Range. Repairs to these remote facilities, often located in public lands at altitudes of 11,000 feet or more, require detailed planning, close coordination with multiple agencies, and creative execution. Issues and solutions discussed include designing repairs in undocumented ground and support conditions, logistical challenges, work in a short summer construction window, stabilization of historically signicant structures, and proect delivery strategies. xamples that illustrate early contractor involvement, exibility in design, and construction solutions are presented.

Jun 23, 2024

PRESIDENT MARKS: This is a matter, I think, in which we are all very much interested, and I know We will have considerable discussion on the subject. MR. GIBSON: Wouldn't it be a fact, Mr. Trick, if a mine was laid off on the block system, it would require less ventilation, less cubic feet of air per minute, and therefore you would have that much better ventilation by

Jan 1, 1926

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

Flotation Research on Cassiterite of Tailings

Sep 13, 2010

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

By David S. Robertson

"IntroductionCanada has been one of the world's leading producers of uranium since atomic energy first became of practical importance in 1942. Indeed, prior to this time, between 1933 and 1940, Canada produced significant amounts of pitchblende, as a source of radium, from the Eldorado Mine at Great Bear Lake*.Uranium was first reported in Canada, however, in the middle of the 19th Century in the vicinity of Theano Point on Lake Superior north of Sault Ste. Marie. In the early 1900s, uranium-bearing minerals were reported in Quebec north of the St. Lawrence River and in pegmatites in Quebec and eastern Ontario. In 1930, G.A. LaBine and E.C. St. Paul visited an occurrence of cobalt reported by the Geological Survey of Canada in 1900, and brought the Eldorado Mine into production in 1933, as noted above, producing, in the main, silver and pitchblende.In 1942, developments in atomic energy were such that the Government of Canada, at the behest of Great Britain and the United States, requested that Eldorado, which had been closed in 1940, be re-opened to produce uranium for the Manhattan Project. In September, 1943, all discoveries of radioactive minerals were reserved to the Crown and their staking by private interests was banned. In January, 1944, the government nationalized Eldorado and formed a Crown corporation, the present Eldorado Nuclear Limited, to take over the assets. That year marked the formal beginning of uranium exploration in Canada.The Period 1944 to 1948In 1944, the Crown Corporation and the Geological Survey of Canada began exploring for uranium deposits, largely in the areas of Great Bear Lake and Lake Athabasca. In that year, A. W. Joliffe of the Survey visited properties on the north shore of Lake Athabasca near Beaverlodge Lake and recommended that Eldorado acquire claims in the area. In 1946, P. St. Louis and E. Laurum, prospectors working for Eldorado, found the pitchblende veinlets that led to the Ace Mine. Shaft sinking began in 1951, and production, through a carbonate leach plant, began in 1953.Continuing drilling on the Eldorado claims led to the Verna ore bodies, some 6,000 feet northeast of Ace, on which shaft sinking started in 1954."

Jan 1, 1986

By Scott Turner

MY YEAR OF SERVICE as president of the A.I.M.E. came at a time when the mineral industry had suffered severely because of disturbed economic conditions throughout the world. The Institute, an integral part of this industry, had been similarly affected. Its membership and revenues decreased; it was confronted by problems of retrenchment at a time when its vigorous operation was especially important to its members, of some moment to the mining industry, and of value to the nation. Throughout the last year, the recession of activity in our industry continued with slight abatement. Your Board accordingly exercised such economy within the Institute as was possible without impairment of essential functions. It endeavored to aid in sustaining the morale of members, their sense of professional unity, and their interest in maintaining research and the interchange of scientific and technologic data upon which the progress of our industry depends. Effort was made to assist in the difficult task of finding employment for needy members; our endeavors have met with some success.

Jan 1, 1933

By Tapan Goswami

The expectation from the blasting engineers and shotfirers is often that explosives will perform optimally at all times. However, in reality, non-ideal situations exist on mine sites and occurrences of poor explosives performance are common. Often the cause is difficult to identify. Having a good application technique and analysis skills will minimise the risk of poor performance. This paper will discuss the experiences gained by the author while blasting in the Hunter Valley, Australia.

Jan 1, 2003

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By N. Mulaudzi, S. Archer

"Direct cobalt electrowinning was developed to produce unrefined cobalt metal as an alternative to producing a mixed hydroxide product (MHP), which is the common cobalt intermediate product in African Copperbelt operations. MHP is preferred due to the high cost of producing high-grade cobalt cathode. Direct cobalt electrowinning test work results have shown that the purity of the unrefined cobalt metal produced from a low-grade copper solvent-extraction raffinate stream was ~97% (w/w), which is significantly higher than the MHP purity (up to 45% (w/w) Co). The current study investigates whether direct cobalt electrowinning would increase the profitability of African Copperbelt copper–cobalt oxide operations, when compared with the MHP flowsheet. An order-of-magnitude economic evaluation was conducted using dynamic differential discounted cash flow models on a “bare-bones” basis, using a 10% discount rate. Three variables were evaluated, namely; reagent utilisation extents, precipitation extents and filter-press wash efficiency. Multivariable risk analysis was also conducted using the Monte Carlo simulation technique to understand the impact of key project drivers. The financial study results indicated that a direct cobalt electrowinning flowsheet could potentially result in a higher mean net present value (NPV) compared with the MHP flowsheet. Cobalt recovery was found to have the most significant impact on the NPV. In addition to increased profitability of African Copperbelt operations, direct cobalt electrowinning has the potential to reduce the environmental footprint of operations as well as addressing the Democratic Republic of Congo government’s drive towards export of higher value metal products instead of low-grade intermediates."

Jan 1, 2015