Search Documents

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

Numerical models play a significant role in the design of safe underground mining excavations and support systems. Advances in the capabilities of numerical modeling software, together with ever increasing computational speeds, have made it possible to investigate the very nature of the large-scale rock mass and its response to mining excavations. The improved understanding of the rock response obtained from modeling enhances our designs, resulting in greater stability and safety of the mining excavations. To help advance the state of the art in this field, the National Institute for Occupational Safety and Health organized the International Workshop on Numerical Modeling for Underground Mine Excavation Design. The workshop was held in Asheville, NC, on June 28, 2009, in association with the 43rd U.S. Rock Mechanics Symposium. The proceedings include 10 papers from leading rock mechanics and numerical modeling experts in the United States, Canada, Australia, and Germany. The papers address a wide range of issues, including various numerical modeling approaches, rock mass modeling, and applications in coal and metal mines.

Jun 1, 2009

By J. W. Thompson

CONSTRUCTION OF STATUTE-SALE BY ENTRYMAN. The timber and stone act (20 Stat., 89) does not forbid an entryman from alienating his interest in his claim; but the act makes illegal any prior agreement by which the entryman acts for another in the purchase. Worden v. United States, 204Fed., 1, p. 4, April, 1913. ASSUMPTION OF DEBT BY GRANTEE-LIABILITY TO CREDITOR OF GRANTOR. A grantee of a mine who agrees to pay the grantor's debts in part payment of the purchase price of the mines becomes to that extent the principal debtor, and the grantor becomes the surety, and the grantor's creditor may in equity enforce his claim against the grantee of the mine, and the grantor in such a case is not a necessary party. Silver King Coalition Mines Co. v. Silver King Consolidated Mining Co., 204Fed., 166, p. 169, April, 1913. RIGHT OF COTENANT TO MINE AND SELL. A cotentant in exclusive possession' of mining property who extracts and sells ore is entitled to charge against the proceeds of the sale the reasonable and necessary expense of its extraction and marketing, as in such case the cotenant is not a trespasser.

Jan 1, 1914

By Robert B. Hopler

"The story of packaged explosives begins with the use of black powder (also called gunpowder) in mining. Although discovered in the 13th century, it was not until 1627 that the first records of use in mining is recorded. It took until the early 1800's before its use began in underground coal. Althougha free-running, granular material, its recommended (and safest) manner of use was for the miner to pour it into ready-made or onsite formed paper bags prior to insertion into the borehole. This was absolutely necessary in horizontal or upward-slanting holes."

Jan 1, 1991

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By Tacio Ferreira

How state-of-the-art software, data analysis and communication applied to drilling and blasting techniques have have allowed quarries in the Midwest of the United States to improve results downstream

Feb 1, 2020

By David Bendersky

The principal objectives of this study are to: (1) survey electrical practices in metal and non-metal mines, (2) survey electrical practices in metal and non-metal mills, (3) clarify the federal regulations governing electrical practices in metal and non-metal mines/mills, (4) analyze electrical accidents, and (5) make recommendations aimed at improvement of the safety of electrical practices in metal and non-metal mines. Information was obtained from literature searches, accident reports, visits to 27 mines and 12 mills, and discussions with knowledgeable industry and government people. The various electrical power systems and practices at the mines and mills visited are described. Similarities and differences based on the type of mining and the minerals being mined or milled are presented. The federal regulations governing metal/non-metal mine/mill electrical practices (Code of Federal Regulations, Title 30, Sections 55.12, 56.12, and 57.12) are presented and discussed. Explanations of each regulation are provided in an appendix. The attitudes of mine/mill operators towards the federal regulations are described. An analysis of the electrical accidents in metal/non-metal mines and mills during the period 1972-1978 is presented. Recommendations, including specific research and development activities, aimed at improvement of electrical safety in metal/non-metal mines are submitted.

Jan 1, 1980

The validity of a steady state assumption made by Adams and Nicol (1986) in the modelling of the elution of gold from activated carbon was investigated. It is shown that the accuracy of the steady state approximation is dependent, not only on the magnitudes of the solution flow rate and reactor volume, but also on the lumped elution rate constant. Under the experimental conditions used by Adams and Nicol (1986) the steady state assumption was inaccurate. This could be circumvented in this instance by applying a rigorous general model which accounts for unsteady state behaviour in the solution and in the activated carbon to the experimental data.

Jan 1, 1997

By Milford L. Skow

MICA is a group name for a number of complex hydrous aluminum silicate minerals that have a sheet or platy structure and extremely variable and complex compositions containing various metallic ions, particularly those from the alkali group. Muscovite and phlogopite, the two varieties of significant commercial value, are the principal consideration of this report; muscovite has major importance industrially. The mica crystal, because of its laminated structure, can be split easily and accurately into thin films that are transparent, flexible, elastic, tough, and waterproof and have outstanding dielectric and insulating characteristics. This combination of properties is not duplicated in any other known substance. The world production of mica can be divided into two main classifications: (1) Sheet mica and (2) scrap mica (including flake mica). In general, separate divisions of the industry produce these two classes of mica, which differ widely in their uses and in the forms in which they are marketed. A glossary of mica terminology is given in appendix A.

Jan 1, 1962

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA's oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996

By F. Taylor Ostrander

Some countries are infinitely poorer than others in mineral resources-despite the perfect equality of their political leaders ambitions. Compare the mineral poverty of Kenya and Tanganyika with the riches of Katanga Province and Northern Rhodesia. Compare Paraguay with Chile, There never has been any equality in the distribution of nature's wealth. Minerals cannot play any role at all in economic development where they don't exist, and there are bound to be differential rates of economic development where there are basic differences in the wealth of mineral resources available. Africa is my principal area of interest and I know that there is an unfortunate but widespread misconception about Africa's "vast mineral resources, "its "untapped mineral wealth." Why is it untapped? Why is it undeveloped?

Jan 1, 1963

By Harvey S. Mudd

WHEN talking about Europe it is well to endeavor to keep politics and economics apart but they have become so intermingled in recent years that the discussion of one topic inevitably leads to the other. Economic influences formerly prevailed over politics but today national and international economies are governed by political forces. Commerce in raw materials, food, and manufactured products is now so restricted by governmental controls that the capacity of the world to produce and to consume, to exchange goods and to pay for them, cannot be gauged by the past or predicted by a multitude of experts. In prewar days there were some yardsticks but today there are none. Thus it is hazardous to make forecasts, for in all fields of human effort the world has been cast upon an uncharted sea.

Jan 1, 1947

By D. Harrington

During the 5-year period 1906-10 inclusive, 84 major disasters (a major disaster being one in which 5 or more lives are lost) occurred in the coal mines of the United States, or an average of 17 per year, and the total number of fatalities from coal-mine gas and dust explosions (major plus minor) for the 5 years aggregated 2,338 or 477.6 per year. The monotonous continuance of coal-mine disasters month by month aroused the people of the United States to such an extent that it was felt necessary for the Federal Government to try to do something looking to the avoidance of the admittedly excessive loss of life in our coal mines, and this was one of the deciding factors in the establishment of the United States Bureau of Mires in 1910. That results have been obtained in this particular cause of coal-mine accidents may be seen from the fact that for the year 1933 but one major explosion disaster occurred in the coal mines of then united States and the total number killed in that disaster was 7. Unquestionably the coal-mining industry through use of oaf or mining practices and aided by the various kinds of work of the Bureau of Mines looking to the prevention of mine fires and explosions is in large part responsible for this very creditable change. If the gas and dust explosion fatality rate of 1.059 per million tons of coal produced during the period 1906-10 inclusive had continued to the first of January 1934, instead of the 6,373 deaths which actually occurred due to gas and dust explosions, there would have been 13,480. Hence, during the 23 years existence of the Bureau of Mines there has apparently been a saving of about 7,102 probable deaths, or an average of more than 300 per year, from gas and dust explosions as against the number which would have occurred had the 1.059 gas and dust explosion fatality rate for the period 1906-10 continued. Thirty-nine persons were killed in all kinds of explosions (both major and minor) in the coal mines of the United States in 1933; if the 1.059 gas and dust fatality rate of the 1900-10 period had been in effect in 1933, about 400 persons world have been killed. Unquestionably, the various teachings of the U.S. Bureau of Mines looking to the avoidance of explosions and fires in mines have had a vital influence in reducing the number of explosions and fires and also in decreasing their destruction in case they occur.

Jan 1, 1934

By R. Farrar

The survey work on protective canopy design was conducted in a 2-month period commencing November 15, 1973. The reported re¬sults under this contract are intended to provide guidance to coal mine operators in complying with federal regulations pertaining to incorporation of protective canopies on underground coal mine electric face equipment. All coal mine electric face equipment manufacturers and 11 coal mines were visited in the course of conducting this survey. Canopy designs currently being manufactured and those now being used underground were examined and discussed with manufacturers, mine operators, machine operators, and safety committeemen. The general objective was to find out what kind of canopies are now being made and used underground, what the operational problems are, and what can be done to secure improvements. Specifically, the survey scope was as follows: a. Survey all electric face equipment manufacturers. b. Survey 10 coal mines (seam height 60 inches and greater). c. Identify current production canopy configurations and minimum mine entry dimensions for each model and type of electric face equipment. d. Assess in-mine operation of canopies developed by manufacturers and/or coal companies. e. Specify optimal canopy configuration and minimum mine entry dimensions for each type and model of electric face equipment.

Jan 1, 1974

By J Joy, A Bye, G V. Kizil

This paper presents an application of the newly developed risk-cost-benefit (RCB) framework to support risk management decisions for the selection of wall monitoring technologies at an open cut mine site. The RCB framework quantitatively assessed the risk of unstable slope-induced wall failure and its impact on both loss of life and coal recovery. The RCB framework was utilised in the selection of an optimum group of risk-controls to effectively manage the risk of wall failure to ensure safety and optimal production occurred. The RCB framework incorporates mathematical modules that integrated RCB calculations and risk-control effectiveness assessments to determine the risk reduction and financial impact of the examined safety initiatives.This paper provides an overview of the five-staged RCB framework, incorporating the RCB decision support tools, RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control Effectiveness Method), and demonstrates its application to slope stability risk management at the case study site. The RCB charts are designed to display a balance between risk, cost and benefit for easy interpretation by decision makers to support the objective selection of an optimum suite of risk-controls. The RCB analysis revealed that a combination of ævisual inspections, automatic extensometers and radarÆ for fast- and slow-wall failures with structure were sufficient to reduce the probability of loss of life (PLoL) to the æModerateÆ zone as defined by the Australian Geomechanics Society (AGS, 2007) for the case study site. The new framework presented in this paper provides a method to effectively determine the suitability of risk-controls and supports industry efforts to reduce risk to as low as reasonably practicable (ALARP).CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Risk-cost-benefit analysis of early warning technologies impact for wall failure risk management in surface mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 55-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Boyd Guthrie

As the American petroleum industry surveyed its position in early 1937, it had many reasons to be optimistic concerning its future. The industry had emerged successfully from the depression, and for the first time since 1929 it had produced over one billion barrels of crude oil in a single year. The demand for gasoline and fuel oils was up, and reserves of crude petroleum and production capacity seemed adequate for the future. Although production of crude oil dropped slightly in 1938, the oil industry was still in a good position with respect to its supply of raw material, which improved economically in 1939 with the decrease of crude-oil stocks in storage above ground. However, by 1940 a threatening cloud (the invasion of France and its rapid surrender) had appeared on the horizon. This aroused Somme fears as to the industry's immediate future, and these fears were intensified the following year when the United States entered World War II. As the war progressed, more and more ships, planes, and vehicles were produced, and the problem of obtaining enough liquid fuels to supply them intensified. Hearings were held in August 1943 before a subcommittee of the Committee on Public Lands and Surveys of the 78th Congress to determine the advisability of passing legislation to promote the development of synthetic liquid fuels.

Jan 1, 1951

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents