Search Documents

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By D. M. Ziebarth

"Normal sequence of operations to develop a new underground mine is: construct and outfit headframe for shaft sinking, sink shaft, construct and outfit shaft sump, develop shaft station and shaft bottom steel. In an effort to reduce the overall project schedule, an innovative plan was developed to install service shaft steel below station level, prior to the completion of the shaft sinking effort. To better evaluate the construction of this substantial steel tower, a preliminary constructability evaluation was conducted, including the best method of supporting the main tower; from the bottom, middle or top of the tower. The design criteria and plan involved: •,Develop access from existing service shaft, 25 km underground •,Use of materials to maximize strength while minimizing corrosion exposure •,Estimating the location of the shaft centerline •,Over excavating the station and shaft below station to allow future shaft steel repositioning •,Designing the tower steel for modular installation •,Incorporate commissioning considerations, such as suspension of the cheese weights during steel installation •,Provision for covered stair access to shaft bottom •,Enclosed shaft envelope with open panels to allow visibility and ventilation The design approach was innovative and this paper will describe the design principles and challenges encountered while providing insight into the solutions developed and implemented; especially the modular construction and installation methodology. INTRODUCTION In an effort to expand the mining operations, a plan was developed to construct a new service shaft closer to the new mine workings and convert the existing service shaft to a production shaft at the Potash Corporation of Saskatchewan Inc. (PCS now Nutrien) Rocanville Potash mine in southeast Saskatchewan. The new service shaft required a multi roped friction hoist operating a cage / counterweight, rope guided conveyances to support the operational requirements. The service shaft is an integral part of the mining infrastructure as it provides access to the underground workings, transport personnel and materials underground for operation and maintenance of the mine. The shaft also allows for services required for safe operation of the underground mine, power supply, controls, communication, dewatering and fresh water supply."

Jan 1, 2019

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

Objective: To enable mine operators and mine inspectors to make quick and accurate measurements of the explosible nature of coal and rock dust mixtures.

Jul 1, 2008

By Jay F. Smith

The Alan Wood BOF Shop consists of two 140 ton furnaces with a rated yearly capacity of 1-1/4 million ingot tons, he hot metal for the BOF Shop is supplied by two 18 foot blast furnaces which produce an average of 2000 tons per day, To achieve the rated ingot ton capacity with this limited supply of hot metal, the preheating of scrap is necessary. This is accomplished in the furnace by using an oxygen-natural gas burner. Piping Arrangement The natural gas and oxygen are piped into the Shop through 8-inch lines to their respective valving stations. As can be seen from Figure 1, the flow of natural gas passes through a flow control valve which is common to both furnaces, after which it divides into two 6-inch lines forming two identical and independent gas control lines, one for each furnace.

Jan 1, 1972

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Tiago Ramos Ribeiro

Os processos de redução direta utilizam-se de gases redutores (CO e H2) para redução do ferro e produção do DRI. A geração deste gás se dá através de reforma de metano que pode ser feita em um reformador, ou dentro do reator de redução com o DRI como catalizador. O último caso ocorre nos processos auto reformadores. A cinética da reforma de metano com H2O catalisada por DRI foi estudada em temperaturas entre 875°C e 1050°C. Os resultados mostraram que até conversão de metano de 0,50, a reforma é controlada por reação química catalítica conforme mecanismo proposto por Münster e Grabke(3,4). Acima desta conversão, o mecanismo não foi determinado. O uso de gás com potencial abaixo do limite para carburação (CH4/H2O < 1) resultou em DRI sem carbono. Com gás de potencial igual ou acima do limite, a carburação do DRI ocorreu e no caso do gás similar ao do processo industrial a carburação impediu a reação catalítica de reforma.

Oct 30, 2017

By Walter B. Hester

All persons and communities that have experienced strong-motion earthquakes are convinced of the importance and complexity of earthquake problems thatmust be solved in order to reduce the personal hazards and property losses to a reasonable minimum. It is also clear that absolute elimination of all risks is impossible. Reduction of existing hazards and precautionary measures which will minimize chances for disaster can be accomplished by realistic appraisal of the effects of recent earth- quakes on modern structures and installations. Localities that have reason to expect so-called strong- motion earthquakes can anticipate these effects by taking appropriate steps. Valid earthquake information can only be obtained from earthquakes. Each earthquake contributes to the body of knowledge by additional facts and by clarification of previous observations. Rational interpretation of the data followed by practical application of the conclusions can contribute greatly to the safety of persons and property. The general public expects the architectural and engineering profession to accept this obligation and render this service. Most earthquake hazards are man-made and arise from the imperfections of the works of man and his failure to anticipate the consequences when the natural characteristics of his environment are ignored. If it is not given to man to prevent such natural phenomena as earthquakes, it is sometimes within his power to control their destructive effects and to reduce to a minimum the toll of life and human suffering.

Jan 1, 1958

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By T. Johnson

Mining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel, cobalt and uranium have been particularly active. The world?s largest nickel mine ? the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale?s Voisey Bay mine in Labrador. Voisey?s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $1.4 Billion Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 ? 250,000 MT/yr manganese carbonate.

Feb 27, 2013

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960

By José Galindez

Tomando como premisa que los procesos, tareas, rutinas y demás actividades relacionadas con la actividad minera han quedado alteradas con la aparición del COVID -19, este artículo presenta y analiza alternativas digitales —tales como dispositivos móviles, plataformas digitales, chatbots, e-learning, programas de mantenimiento digitalizado, logística robotizada y uso de drones— que hoy resultan imprescindibles para continuar operando de manera segura.

Jul 30, 2020

Choosing the correct delay time for many blasting applications is an important and critical blast design parameter for controlling fragmentation, muckpile shape, swell, digability, throw, ground vibration and airblast. BAl and its affiliates have monitored thousands of full scale blasts in a variety of field conditions, spanning over 15 countries, with sophisticated blast monitoring instrumentation. In some blast environments, a small change in the choice of delay times used had a dramatic and pronounced effect on the overall blast results. In other blast environments, large changes in the choice of delays used had absolutely no effect on the final results in terms of specific outputs. In environments which were sensitive to the delay selection, the type of explosive, dynamic response time of the rock mass (TMIN), integrity of the material, burden and rock mass geometry, all played a very important ,role.

Jan 1, 1998

By Bertil I. Pålsson

The most common REE containing mineral that is worked today is bastnäsite. It means that mineral processes are adapted to it and that the metallurgical separation techniques for winning of individual REE are adapted to bastnäsite concentrates. For all other deposit types, suitable mineral processing methods and separation technologies need to be adapted and/or developed. Preliminary mineralogical analyses indicate that slightly less than half of the REE in the tailings dumps at LKAB/Kiruna are associated to apatite. The rest is in the minerals monazite (maybe associated to apatite) and allanite. At least allanite is probably not floatable with reagents commonly used for apatite. Mass and element distributions for the tailings sand reveal that very little apatite is present above 300 µm, and that approx. 30 % is below 20 µm. REE does not follow P2O5 completely and are also present in coarser fractions. Flotation results show that the best condition for both apatite and REE winning is pH 9, high collector addition and low dosage of water glass. Under these conditions, the lab-scale flotation gives an apatite concentrate with at least 30 % P2O5 at 70 % recovery. REE follows apatite in the cleaner steps but only partly. Its recovery is approx. half compared with apatite. The reason for the low REE recovery is likely to be that REE to a large extent is trapped in non-winnable minerals, especially allanite. The REE grades in the concentrate are expected to be in the range 3000 ? 4500 g/ton. Keywords: flotation, REE, apatite, monazite, allanite

Sep 1, 2012

By John W. Frey

Although there are certain general uniform provisions in the laws ... of the several Provinces of Canada the differences are so great that it is considered advisable to present digests of separate mining laws rather than a digest of Canadian mining law as an entity . This analysis , accordingly , has been divided as follows : Nova Scotia , New Brunswick , Quebec , Ontario , British Columbia , and a group of Provinces under Dominion Law .

Sep 1, 1930

By Hargraves A. J, Smith J. W

Experiments conducted at Tahmoor Colliery, Sydney Basin, have demonstrated the variability in chemical and isotopic composition of seam gases issuing from boreholes in the Bulli seam and desorbing from lump coal from the same source.From this work it appears that an immediate preferential release of methane accompanies the physical disturbance of the coal seam by penetration with development or drilling or by detachment. In addition, both early released methane and carbon dioxide are depleted in 13C relative to later desorbed gases, therefore the analyses of gas samples taken after such events may not reflect the true bulk composition of the undisturbed seam gas in situ. A method for overcoming this problem by taking gas samples at depth in the "steady state" is proposed.

Jan 1, 1987

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971