Search Documents

Presentation Outline ERM ? corporate profile Background to sustainability reporting GRI G3 Guidelines (Oct 2006) Best practice examples Contact information ERM ? corporate profile Over 35 years of experience World?s largest all-environmental consultancy* 130+ offices in 40+ countries; 3,200+ professional staff Worked with >50% of the Global Fortune 500 (FY07) Annual turnover > US$500 M (FY07) 2008 Environmental Advisor of Year** Offices/Staff ? Canada (5/50) and US (65/1,350) *Source: Engineering News Record: July 2, 2007 ** Source: Acquisitions Monthly: December 2007

May 1, 2008

By Evan Brinkerhoff, Steve Chorley

The largest hard rock TBM ever to bore in the USA, an 11.6 m diameter Robbins Main Beam TBM, recently underwent a planned in-tunnel diameter change to a more compact 9.9 meters. The first-of-itskind conversion process for the Main Beam TBM was undertaken 2.8 km into the bore and was not done inside a shaft or pre-excavated portal. This paper will detail the unique dual-diameter machine designed for the Mill Creek Drainage Relief Tunnel in Dallas, Texas, USA, machine performance, and successful size conversion process that took place in early 2021—a process that utilized the four C’s of construction to enormous benefit: Communication, Cooperation, Collaboration and Coordination.

Dec 1, 2022

"INTRODUCTION These safety standards for anthracite mines have been prepared for use as a guide for Federal inspectors. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7282 issued in May 1944 and used as a guide in Federal inspections. No provision made in these safety standards should be construed or operate to nullify any existing State statutes; they are intended to supplement the State statutes in the interest of increased mine safety. Mines are inspected in accordance with the Federal Coal-Mine Inspection and Investigation Act of 1941, Public Law 49, 77th Congress, H. R. 2082. Any unusual hazard noted by an inspector and not covered by these standards will be discussed in the inspection report, and suitable remedial procedure will be recommended.ARTICLE I. - SURFACE STRUCTURESSection 1. Breaker and cleaning plant.Electric switches and controls in breakers and cleaning plants should be enclosed.Where coal is dumped at or near air-intake openings, reasonable provisions should be made to prevent the dust from entering the mine.Section 2. Lamp houseNaphtha or other flammable liquids in lamp houses should be kept in approved containers or other suitable dispensers.Flame safety lamps should be permissible and maintained in permissible condition.Flame safety lamps should be properly cleaned, examined, and assembled by a qualified lamp attendant or other competent person before each period of use. Lamp assembly should again be checked by the person using it immediately before he enters the mine.When not in service, methane indicators, flame safety lamps, and electric cap lamps should be in the custody of competent persons responsible for maintenance and testing."

Feb 1, 1948

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

Small scale gold mining operations in Papua New Guinea (PNG) have been observed to use very low flow rates of water in sluice boxes. In a series of laboratory experiments carried out to determine whether this approach was unsatisfactory or not for their situation, indications were obtained that it had some advantages in the recovery of fine gold but at the cost of considerable throughput. The separation mechanisms operating in such a system are analysed.

Jan 1, 1986

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls were a big part of the problem. They killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, which is the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How was this historic goal achieved? This paper starts with a modern analysis of the causes of the roof fall fatalities in 1968. Then it follows the reductions over time by category, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The paper shows that in 1968, more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Jul 1, 2023

By J Coombes

"In today’s challenging climate of reduced staffing, limited funding and uncertain markets, we are called on to operate more productively and ‘be more innovative’. As an industry, we are quick to identify our practice areas as a mark of our role in the machinery of the mine value chain. We proudly note our profession – ‘geologist’, ‘mining engineer’ or ‘accountant’ – and demarcate our responsibilities and even our physical space. We even subdivide our disciplines into sacred entities such as ‘logging geologist’, ‘resource geologist’ or ‘structural geologist’ to prevent any blurring as though somehow the confusion will cost valuable disciplinary ground. How can we function professionally to heed the call to be more productive and more innovative?The purpose of this paper is to underscore what is expected from project evaluation, examine the ways in which we work as an industry and explore alternatives used in other industries and environments.The paper begins with a summary of project evaluation expectations and the ways in which disciplines typically interconnect when conducting project evaluations. Next, the paper examines alternative work frameworks and making a distinction between multidisciplinary, interdisciplinary and transdisciplinary frameworks. In-practice examples of these frameworks in alternative industries and contexts provide evidence for application as well as an opportunity to examine their pros and cons.The paper closes with a call to re-examine working practices in the mining industry, with a view to enhancing productivity and heeding the call for greater innovation.CITATION:Coombes, J, 2016. Transcending the mining discipline divide – multidisciplinary, interdisciplinary or transdisciplinary?, in Proceedings Project Evaluation 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A B. Christie, R L. Brathwaite

Since the first occupation of New Zealand in 800 - 900 AD, various useful minerals, rocks, and energy resources have been identified and extracted. The Maori prized greenstone for ornaments, tools, and weapons, used argillite and obsidian for tools, and decorated their carvings and bodies with colours made from clays, limonite, and vivianite. They were aware of coal (waro), but are not known to have used it for fuel. Before 1840, visiting whalers used coal from Shag Point to heat their trypots. Mining activities got underway in the 1840s, with the finding of manganese oxide deposits in the Bay of Islands, Kawau Island, Waiheke+ Island, and Taieri Mouth. Secondary copper ore was mined on Kawau Island (1846 - 1869), and native sulphur was exported from White Island to Europe. The discovery of gold at Coromandel in 1852 and a few years later in Northwest Nelson and Otago opened the way to gold rushes in these areas and subsequently in Marlborough and Westland. Mining of alluvial gold evolved through sluicing to the invention of gold dredges; first (1863) was the simple spoon design, but later (1881) large steam-powered bucket-ladder machines weighing around 3800 tonnes were built. Most of the gold dredges had gone by the early 1960s, following a revival in the 1930s, but one large dredge operates today on the Grey River. Other mining events included: underground mining of coal from 1849 and underground mining of lode gold from 1863 in the Coromandel, Reefton, and Otago fields. Most outcropping coal deposits had been discovered by 1870. Building stones were used by the early settlers for construction of houses, churches, banks, public buildings, and some universities from 1836. Aggregate for roads, railway ballast, and concrete, and limestone for cement and fertiliser, and clays for bricks and china have been quarried for many years.

Jan 1, 1993

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By George Markon

The importance of United States coal exports as a component of the national economy, the potential for growth of these exports, and the inter-national character of this sector of the coal industry are described in this report. The report summarizes some of the many background elements in the rise of United States coals to preeminence in highly competitive world markets. It presents some insight into this important sector of United States industry and the positive contribution of this sector to the Nation's balance of payments. It contains pertinent basic statistics on production, trade, and consumption of coal in most major markets for 1960-66. The report examines the movement of United States coals from mines to export markets, tracing and describing origins, exit ports, prices, and trends as well as inland and ocean freight rates and other data vital to an under-standing of some of the practices and complexities of the United States coal markets abroad. A brief sketch of coal production and consumption in principal importing countries is also presented with a short review of some of the more current practices and problems of these countries. Coal produced in inland areas of the. United States can be moved to and distributed economically within coal-producing countries overseas and in Canada. Quality coals from the United States can successfully compete with foreign coals in nearly any area of the world on a truly economic basis because of their high grade and their low cost which derives from the high productivity of the miner and from reasonable ocean freight rates. Because of tariffs, trade embargoes, quotas, and other restrictions, how-I ever, foreign coal markets are relatively limited. Further limitations are imposed in some countries by economic conditions which restrict all imports as a matter of financial and economic necessity. Despite these obstacles, United States coals have brought lower cost quality coals to a large segment of the foreign energy market.

Jan 1, 1968

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019