Search Documents

By J. Howard Bird

The purpose of this publication is to describe the power-distribution system of the mine and refinery of the Duval Sulphur & Potash Company at Carlsbad, N. Mex. This distribution system has been excellently predesigned to meet requirements and fit special conditions encountered at the property. In presenting the material, the authors point out various features that would be desirable for incorporation in other systems under similar conditions. Central location of switchgear in pressurized vaults and ventilation of such equipment with filtered air prevent salt accumulations and contribute to trouble-free operation. The simplification of power-distribution circuits and overload protection, as a result of centralization of switchgear, the use of individual control circuits enclosed in conduit (which aids troubleshooting), and central location of control panels, are factors which contribute to efficient, safe operation. Those features are applicable to many operations where fire or explosion hazards are encountered, or where dusty conditions may exist, as well as in operations where numerous individual drives are involved.

Jan 1, 1959

By G R. Ballantyne, G Lane

Dry milling circuits that include high pressure grinding rolls (HPGR) or vertical roller mills (VRM) and air classification have replaced dry ball milling in cement production, but how do they compare to wet milling and classification circuits in mineral processing plants? Two case studies are presented that compare the energy efficiency, wear, liberation and capital cost of dry and wet milling circuits. In both case studies the VRM and HPGR consume half the energy of a wet tumbling mill for the same duty. However, the dry classification system tends to significantly erode the energy benefits. A number of improvement opportunities are presented that have the potential to improve the energy and capital efficiency of dry milling circuits. These improvement opportunities focus on the dry classification system that consumes significant energy in heating and fan power requirements and requires a large proportion of the footprint.

Aug 24, 2022

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

By Jae-sang Ahn

As the amount of construction information used in the growing construction field increases, the importance of efficient construction field management has been growing. Therefore, construction industry have been tried to introduce and conjugate various software and IT technology such as PMIS, Web Camera, RFID, GPS, PDA. However, existing IT technology especially PMIS have not been performed systematically because of difficulty of real time information collection and decision-making from the insufficient handy equipment. These problems make construction manager cannot efficiently respond to diverse condition occur in construction sites. In addition, after the completion, individual who use PMIS have to move another site and use another system so than cannot use information from previous sites. On the other hand, development of IT technology transmute PDA phone for text-based work like schedule management, internet research to smart phone for network based multimedia service. In other words, smart phone is not just IT equipment but new way for overall industry and it can satisfy the demand IT technology on construction sites. Therefore, the purpose of this study is introduce mobile based individual unit PMIS system using cloud computing and SNS which is in development progress. It is expected to be possible to collect and record the real-time information that occur at the site and make rapid decisions based on the recorded information, by converting the office works that are managed based on the site PC or Web, if the site management system that is based on the smart phones and Cloud computing that will be constructed through this research are utilized. After this study, it is necessary to research about interwork with project unit PMIS system and test on real construction site.

Aug 1, 2013

By Elizabeth M. Smith

The kcICON design-build project in Kansas City, Missouri includes widening the existing roadway, improving interchanges and grade separation bridges, and replacing the Missouri River Bridge. The Missouri Department of Transportation (MoDOT) typically utilizes steel H-piles and steel pipe piles as driven pile support for bridges. After bidding the kcICON project, the cost of steel rose significantly and the design-build contractor used an innovative approach to reduce foundation costs without significantly affecting the project schedule. The kcICON team conducted a value engineering evaluation of alternative foundation types for use at four grade separation structures. The result of the value engineering evaluation was selection of precast, pre-stressed concrete (PPC) piles as the preferred foundation alternative. Terracon developed a test program to evaluate the performance, capacity, and suitability of PPC piles at the site using a PDA and CAPWAP analyses. This paper presents the value engineering design, rationale for selection of PPC piles, results of the pile test program, and findings during production pile driving. The collaborative approach to the project by MoDOT and the kcICON team, combined with testing and a site-specific design approach, resulted in substantial savings for the design-build contractor.

Jan 1, 2009

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976

By Davis RA, Wasp EJ, Cowper NT

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New- York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering' this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three-year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1969

By A. C. Fieldner

ONE of the important functions of the Bureau of Mines is the, analysis of coal from every coal-mining State and Alaska. These analyses are being published for use of Government officials and the public. In connection with analytical data showing composition and quality of coals of the States, consumers, Producers, and the general public will be interested in a brief description of the geologic structure of the coal basins, typical mining conditions in the several districts, and the principal economic data of the industry. These publications have therefore heel) designed to include such features to present concisely the principal facts regarding occurrence, reserves, duality, characteristics, production, and uses of coals of each producing State.

Jan 1, 1952

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects'of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By G. S. Hume

THE discovery of natural gas with naphtha in 1924 in the Upper Palaeozoic limestone of Turner Valley, 35 miles southwest of Calgary, has led to continuous developments in this field. Drilling undertaken soon after this discovery demonstrated that the anticlinal structure was in reality a major drag-fold cut off on the east side by a westerly inclined fault of large displacement. The faulted edge of the .limestone at depth determines the eastern limits of the field, which between 1924 and 1936 was shown to have a gas area 14 miles long by about 1 mile wide. Since the strata dip westerly, away from the axis of the fold, drilling becomes progressively deeper to the west and, with the advent of deeper drilling, crude oil was discovered in 1936 on the west flank of the structure but in the same porous reservoir rocks as the gas on the crest and upper parts of the fold. Since 1936, drilling has been undertaken wholly for the production of crude-oil and at present two producing areas have been found within the Turner Valley structure. The larger of these, at the south end of the field, in the vicinity of Highwood river, has a length of about 4 3/4 miles and a proved width of one mile, whereas the smaller, in the north end of the field, south of the north fork of Sheep river, has only a few producing wells.

Jan 1, 1939

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By A. Hayatdavoudi, D. Chitila, F. Boukadi

"Shale oil and gas have provided a tremendous boost to energy production in the United States even though the characteristics and behavior of shale are yet to be fully understood. Hydraulic fracturing is often applied to horizontal shale wells to stimulate production. This experiment seeks to determine effects of cyclic variable temperature, water vapor and exposure time on shale micro fracture propagation. We used 22 small Pierre shale specimens and subjected them to aforementioned conditions. Fractures developed in 19 specimens. Combination of high temperature and high water vapor generated the largest number of micro fractures on the specimen surfaces.INTRODUCTIONShale oil and gas have contributed immensely to energy independence in the United States. Most if not all shales depending on their total organic content (TOC) and their clay content bear the promise of being a source rock. For example, the Eagle Ford shale play, located in south Texas, is one of the key contributors to the recent rise in oil and gas production in the United States. Data from the U.S. Energy Information Administration (EIA), published in 2014, states that monthly oil production from Eagle Ford wells increased from 340 barrels per day (bbl/d) in January 2009 to nearly 1 million bbl/d in June 2013. Natural gas production has also increased at a similar rate over the same period, from 5.8 million cubic feet per day (MMcf/d) to nearly 4,000 MMcf/d (EIA, 2014).According to the railroad commission of Texas (RRC) 2014 published information, the Eagle Ford shale play is an important play because it produces gas and more oil than other shale plays in the United States. It is an organic-rich play with carbonate shale percentage in the 70% range in south Texas and the shale content increases moving to the northwest. High carbonate proportion renders this play brittle and suitable for hydraulic fracturing treatments."

Jan 1, 2015

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By A. Mainza, A. Mabentsela

A finite element model of a 5 m radius DC arc ilmenite furnace in idling mode was used to test the notion that the slag solidifies when it comes in to contact with colder pig iron, thus constituting the initial step in the formation of solid slag at the slag-pig iron interface. It was found that a slag that is 150°C hotter than the pig iron does not solidify at the interface. The 150°C temperature difference between the slag and pig iron is a result of solid slag at the slag-pig iron interface, not the other way around as suggested in the literature. Calculations show that the thickness of the frozen slag at the slag-pig iron interface is 1.7 cm for the furnace used. It is proposed that slag solidification begins with the slow co-current flow of molten slag and pig iron in the outer parts of the furnace. This provides enough time for molten slag to interact with molten pig iron without solidifying. As the reduction products form due to reduction of the slag by carbon in the pig iron, the slag solidifies. This approach negates the need for the slag to solidify by merely coming into contact with an inherently colder pig iron. Making use of a low thermal contact conductance between the slag and pig iron was found to be sufficient to numerically capture the presence of solid slag at the slag-pig iron interface and to preserve the 150C difference between the slag and pig iron phase.

Mar 30, 2023

For Australian mining projects, sustainable groundwater use is typically defined as a groundwater extraction regime, measured over a specified planning time frame, which allows acceptable levels of stress and protects dependent economic, social and environmental values (DEH, 2004). This principle is compatible with most stakeholdersÆ understanding of our national environmental objectives, yet the application of this policy on a project-specific scale is not always straightforward. Three examples of sustainability issues in the management of groundwater in mining are presented. These examples highlight each of the three dependent values: environmental, economic and social.

Jan 1, 2006

By John H. Soulé

This paper describes the location and general features of the ?Red Bed? or sandstone copper deposits in southeastern Colorado and New Mexico. Most of the areas containing this type of deposit were visited, and many deposits were examined. Some deposits were not visited because of lack of information as to their location. In the large area covered a great variety of climatic, geographic, and topographic conditions exists. Some of the deposits are in arid areas, whereas others are in heavily forested regions. Altitudes range from 3,400 to 9,200 feet, and the terrain varies from flat plains to rugged mountains. Transportation is a difficult problem in most of the districts, involving long truck hauls to a railroad and long rail hauls to a smelter.

Jan 1, 1956