Search Documents

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By David W. Tongue

This report describes the engineering work leading to the design of an underground coal mine piping system to transport approximately 2,000,000 cubic feet per day of methane gas to the surface from degasification holes drilled horizontally into the coalbed in existing coal mines. Safety instrumentation for detection of gas leaks and provisions for automatic emergency shutdown are included in the design. It also includes specifications for a safe system of handling gas, water, and drill cuttings during drilling of the horizontal holes and recommendations for compressor and metering facilities at the surface. The main pipeline is recommended to be constructed of polyethylene plastic pipe joined by a butt fusion method while lateral lines and separator and meter piping at the horizontal holes are recommended to be screwed steel piping. The materials used are to be resistant to the forces of impact exerted by falling rock. The pipelines are to be suspended from the ceiling with pipe hangers. All steel components are protected from chemical corrosion by applying protective coatings and the vertical casing to the surface is protected from electrolytic corrosion by a rectifier station. Methane gas detectors monitor the mine atmosphere to detect the presence of gas leaks and a pneumatic plastic tubing line provides for control of the safety shutdown system. Both the recommended design and the required construction procedures are in compliance with the applicable Federal codes for coal mine safety.

Jan 1, 2012

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco's Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987

By Oliver Bowles

In its geologic sense the term marble is applied to rocks consisting of crystallized grains of calcite or dolomite or a mixture of the two. Although limestone has the same chemical composition as marble it differs in that the component particles of calcium or magnesium car- bonates are granular and noncrystalline. In marble the crystals may be intimately intergrown, whereas limestone is an aggregation of unrelated particles cemented together into a solid mass. In its commercial sense the term marble has a much wider applica- tion. As susceptibility to polish is one of its chief commercial assets, all calcareous rocks capable of polish are classed as marbles. Lime- stones that show little crystalline structure may, if they take a good polish, be classed as marbles. Furthermore, serpentine rocks, even if they contain little calcium or magnesium carbonate, are classed as marbles, as they are commercial substitutes of true marbles.

Jan 1, 1916

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By Robert G. Lundquist

The Bureau of Mines compared longitudinal strain energy output of a percussive drill to energy determined by measuring maximum piston velocity. Strain gages were used to determine the strain-time waveform and its amplitude at seven levels of operating pressure and eight levels of thrust. The longitudinal strain energy was found to be approximately 14 ft lb less than the maximum piston energy at comparable operating conditions.

Jan 1, 1969

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By C Adams

Reports of delays and cost blowouts in major study and construction projects are becoming increasingly prevalent in the resources industry. This is mainly being attributed to an escalating cost environment associated with the increased number of projects in the development to construction pipeline and a scarcity of competent skilled resources to deliver these projects. However, not all this effect can be directly attributed to the current environment. Historically the mining industry has not performed well in its ability to deliver projects according to the financial and physical parameters forecast in the feasibility study process. To manage the risks associated with delivery of major projects, resource companies need to ensure they use a standardised approach to management of their project development to satisfy project objectives and enable more efficient use of the increasingly limited available resources. Each discrete step in advancing the project from scoping study to operations needs to be integrated, reducing the amount of rework and duplication. This paper is primarily a consolidation of existing ideas on project management systems but also introduces new concepts to solve current issues. It describes the basic components of a typical mining project, the issues that commonly arise, the key attributes, and critical steps required for an effective integrated project management system covering projects from initial scoping studies through to project commissioning and operation. This paper focuses on technical study components of the mine development project with allowance for transitioning to design and construction and operation phases.

Jan 1, 2006

By A M. Ebbels

"Underground mine scheduling decision-making has been based on production requirements, equipment productivities and the mine planner’s instincts on the best scheduling strategy for the mine to optimise the net present value (NPV) of a project.In the last few years, innovative software has been developed to optimise underground schedules based on NPV. The schedule optimisation tool (SOT) allows the user to set up scenarios based on grade, metal content, capital and operating costs.This paper discusses the results of two case studies undertaken using the SOT software to optimise the NPV of the projects.In each case study, the SOT software has been applied in two ways:using the original mine planner’s scenario and determining whether the NPV could be improved by changing resource capacitieschanging the scheduling goals to determine whether a different mining strategy would have a better NPV outcome.The outcomes of the case studies demonstrate that the mine layout and design were contributing factors to the overall improvement of the NPV and that SOT has a more noticeable impact on the NPV of projects where less sequence constraints are required, such as geotechnical sequencing and access development.CITATION:Ebbels, A M, 2016. Optimising underground mining strategies, in Proceedings Project Evaluation 2016, pp 60–65 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974

The Martha deposit is an economic giant epithermal gold deposit, with mined and unmined resources of more than 218 000 kg (7 Moz) Au. The Au-Ag, base metal sulphide-bearing quartz lodes in the Martha deposit form an extensive braided pattern within hydrothermally altered andesite wall rock. There are five main quartz lodes: 1.      Martha, 2.      Welcome, 3.      Edward, 4.      Empire, and 5.      Royal.   Information from historic mine plans and reports has been used to determine the depth distribution of economic ore within the Martha deposit. Economic ore (average of 10 g/t Au) in the Martha underground mine was at a maximum width and strike length between a vertical depth of 160 and 350 m. Below this depth the quartz-sulphide lodes continue, but the grade declined to sub-economic grades (< 4g/t Au) at about 575 m depth and economic ore shoots were localised, mainly on the hangingwall side of the lodes. Samples from exploration drill holes indicate that this decrease is associated with a depth zonation from electrum-bearing Zn-Pb-Cu-Ag sulphide ore (average 10 g/t Au) to sub-economic (< 2 g/t Au) electrum-poor Zn-Pb sulphide mineralisation.

Jan 1, 2006

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores and rock minerals is constantly required to develop new means and methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes f physical separation. Thus, in 191.9, Coghill and Bonardi 31 published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/, Schwartz 5/, and Head and his associates6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and. the University of Alabama.

Jan 1, 1940

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982