Search Documents

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Matteo Tomba

Today’s steel market is characterised by high competitiveness and tight profit margins; therefore, the operational costs of rolling mills must be as low as possible, while ensuring a final product of the highest quality standards. PERT SRL is an engineering company with a long-term experience in the international steel market, specialised in the design and supply of highly innovative and bespoke solutions for siderurgical and environmental plants. Because of its strong commitment to deliver excellent products and services, and its ability to innovate and adapt to the fastchanging market requirements, PERT has studied a new generation of BI-SUPPORT rolling stands, designed to be used in rolling mill plants for the production of rebars, rounds and sections in special quality bars (SBQ) steel grade, wire rod, light and medium section, suitable also for special steel plants. This paper will provide a deep insight into the key technical and economic features that have revolutionised the rolling technology for long products, such as the absence of spindles and piping on board, the considerably reduced number of spare parts required, a ring gap regulation system, and the compact dimensions, which lead to significant savings in investments and production costs; at the same time, the BI-SUPPORT stands guarantee excellent standards to the final product, an increase in plant productivity and a general improvement in the plant management.

Aug 16, 2017

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Carolina Gomes Dias Ribeiro

The modern composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace. Natural fibers composites with biodegradable polymer matrices are considered environmentally friendly materials and currently accepted as possible substitutes for synthetic composites. These green composites can be safely discarded or composted at the end of their life without harm to the environment. Another alternative for synthetic composites is to apply natural lignocellulosic fibers as reinforcement of conventional polymer matrices and already used in the automobile industry. In addition to the environmental and societal advantages of the green composites, the lignocellulosic fiber reinforced conventional polymer composite also has economical and technical advantages. In the case of a fiber collected as a waste, the price of the composite can be considerably lower than “fiberglass”. Furthermore, with high strength lignocellulosic fibers such as sisal, ramie and malva the specific strength of a composite may approach that of “fiberglass”. Therefore the objective of the present work is to investigate the mechanical behavior of polymer matrix composites reinforced with high volumes of natural malva fibers subjected to tensile stresses.

Aug 16, 2017

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Marcus Vinicius Laudares Mendonça

SMS calculates and improves tooth and flank profiles individually to realise a homogeneous pressure distribution over the complete load flank. With a tooth profile and flank profile according to AGMA, ISO or DIN standard the contact pressure varies along the load flank. To realize a homogeneous distribution of the contact pressure and to avoid a premature mesh, SMS improves the tooth profile and flank profile in three steps. First SMS is doing a preliminary calculation and design according ISO, DIN or AGMA standard, with safety factors based on more than 125 years of experience. Second SMS calculates and checks the local contact pressure at the load flank under consideration of shaft, gearing and housing deformation, as well as the bearing behaviour. Finally SMS calculates and designs an improved tooth profile and flank profile to receive a homogeneous contact pressure at the load flank. The result is an increase of the torque transmitting capacity of up to 30% of the SMS advanced gears with the same outer dimensions than traditional gears.

Aug 17, 2017

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Zou Zhongpping

Under the new normal state, blast furnace outputneeds to be adapted to the market demand, however the limitation in blast furnace output has significant impact on blast furnace operation and is prone to cause inactive furnace hearth and higher fuel ratio. To address such problems, some practices to maintain stable and smooth operation of blast furnace in case of output limitation are proposed based on data analysis philosophy, which allows the blast flow and hence the top pressure to be determined based on the hot metal output, and adequate kinetic energy of blast supply can be assured by adjusting the tuyeres. Matching between the oxygen enrichment and the pulverized coal injection is also proposed based on theoretical flametemperature, and burden distribution cycle calculation method is proposed, whichoffersnew approach for analyzing the change in burden distribution pattern.

Oct 30, 2017

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By José Claudio Blanco

A medição de Planicidade sem contato (contactless) para Laminadores a Frio é efetuada com o sistema conhecido como SIFLAT. Os sensores utilizam tecnologia eddy current como medição precisa de amplitude entre o sensor e a chapa na qual será medida a planicidade. Os resultados convertido para valores de planicidade são de alta qualidade e precisão na mediação que serão posteriormente enviadas ao sistema de controle de planicidade. Este sistema é aplicado em laminadores de chapas a frio e linha de processo.

Aug 16, 2017

By Gerhard Finstermann, Ichiro Maeno, Takehiko Saito, Hironori Shimogama, Konrad Krimpelstätter

Automobile manufacturers are developing Electrified Vehicles with light steel body structure designs that reduce mass and therefore greenhouse gas emissions over the vehicle’s entire life cycle. This raises the demand for the production and development of Advanced and Ultra High-Strength Steels (AHSS / UHSS) and Electrical Steels with increased permeability and reduced core loss to improve energy conversion efficiency. To meet this requirements the steel market is tending towards new generations of AHSS with improved formability (3rd generation AHSS) and high-silicon steels with higher strength and thinner products. With this growing demand for advanced high-strength steels and electrical steels, producers are faced with a unique and interesting challenge in producing materials that strain or exceed the capabilities of existing mill equipment and automation designed to produce low- to medium-carbon sheet. While specialty steel producers have known for decades how to process special high-strength steels and thinner gauges, this equipment typically does not offer the yield and productivity desired by the market, necessitating innovation in re-engineering existing equipment to meet the market demands more economically than new construction. In the case of cold rolling, this can be supported through variable roll geometries, more effective roll-gap lubrication technologies, application of strip heaters (Warm Rolling) to reduce risk for edge crack propagation and strip breaks as well as continuous rolling managed by state-of-the-art automation technologies.

Oct 1, 2019

By Ramon Valls Martin

A obtenção das propriedades magnéticas do rejeito do processamento do minério de ferro auxilia na determinação da viabilidade da recuperação do ferro residual. Também permite a otimização dos parâmetros operacionais do processo de concentração por separação magnética. Foram apresentados dois métodos de caracterização magnética: Método indutivo (histeresígrafo) e método de força magnética (balança de susceptibilidade). Estes métodos têm como vantagens o baixo custo e rapidez de execução. Apresentaram sensibilidade suficiente para a caracterização de amostras de resíduos com teores de ferro muito reduzidos.

Aug 16, 2017

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019