Search Documents

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By Anna Carolina Cerqueira Neves

Synthetic fibers have been gradually replaced by lignocellulosic fibers. Compared to the synthetic fiber, natural fiber showed economic and environmental advantages presenting interfacial characteristics with polymer matrices that favor the impact energy absorption by the composite structure. However, so far little has been reported about the hemp fiber embedded in polymer matrices, such as tensile properties. This study aims to evaluate the resistance in tensile tests of epoxies composites reinforced with different percentages of hemp fiber. Tensile tests were submitted with percentage of 0%, 10%, 20% and 30% incorporated hemp fiber in epoxy matrix. The tensile strength and deformation substantially increased the relative amount of hemp fibers incorporated into the polymeric matrix.

Aug 16, 2017

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Evan Thomas

It has been shown before that liquids can slip at a solid boundary, which prompted the idea that parallel-surface bearings can be obtained by the use of alternating slip and non-slip regions in the direction of fluid flow. The amount of slip at the wall depends upon the surface tension at the liquid - solid interface, which in turn depends on the chemical composition of the surface and its roughness. In the present study a heterogeneous surface was created by coating half of a circular glass disc with a coating repellent to glycerol. A rotating glass disc was placed at a known distance above the coated stationary surface and the gap was filled with glycerol. With the top surface moving in the direction of slip to non-slip region, a pressure build up can be theoretically predicted. The pressure gradient in the two regions is constant, similar to that in a Rayleigh step bearing, with the maximum pressure at the boundary. In order to accurately measure the force generated by the pressure increase, a load cell was attached to the heterogeneous disc. Experiments were conducted by varying both sliding speed and distance, and the resultant load carrying capacity was measured and compared with theoretical calculations. This allowed the slip coefficient of the coated surface to be evaluated.

Jul 31, 2018

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Giulio Rodrigues Altoé

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of epoxy matrix composites reinforced with continuous fique fiber, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Aug 16, 2017

By Edgar Ivan Castro Cedeño

En la producción de aceros limpios el control inclusionario es crítico para la obtención de un producto que cumpla con los requerimientos de calidad. El análisis de la distribución de tamaño de inclusión mediante modelos estadísticos permite estimar la incidencia de inclusiones en el producto solidificado a partir de mediciones tomadas en muestras relativamente pequeñas. En seis coladas de acero bajo carbono desoxidado con aluminio se tomaron muestras de acero a lo largo del procesamiento en horno olla y colada continua. Las muestras se prepararon para estimar mediante análisis metalográfico los tamaños de inclusión. Los datos de tamaño de inclusión se analizaron mediante modelos estadísticos de valores extremos, se hace una comparativa entre la distribución Gumbel (que forma parte de la norma ASTM E-2283) y la distribución Generalizada de Valores Extremos (GEV). Mediante una prueba de hipótesis con el estadístico Anderson-Darling, análisis de cuantiles y con la función de supervivencia se demuestra que la población inclusionaria se describe de una mejor manera con la distribución GEV. Finalmente se da un estimado de la incidencia probable de inclusiones en el producto solidificado.

Aug 16, 2017

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Eduardo Dominguez Trindade

Lubricant oils are subjected to reciprocating movement in the piston ring/cylinder tribocouple of automotive engines. In this kind of movement, the relative speed oscillates between zero and a maximum, and therefore the lubrication regime goes from boundary to hydrodynamic. Tribotests are widely used in laboratories to hint at the friction developed in these systems. In the present work, a SRV tribometer was used to evaluate the friction behaviour of lubricant oils under reciprocating movement up to 60 Hz. A high acquisition rate allowed the analysis of data inside each reciprocating cycle. Both a pure base oil and a fully formulated lubricant were used. Changes in the contact pressure, viscosity and speed were seen to influence friction, which was correlated to the relative thickness predicted by Hamrock-Dowson equation. While some observed characteristics were typical consequences of the Stribeck curve, other effects were also observed, such as the occurrence of seizure at high reciprocating frequency. A lower boundary coefficient of friction due to additive package in the formulated oil was also observed. The results allow a better understanding of friction in reciprocating cycles and can be used to evaluate the performance of oils and surfaces in laboratory prior to engine testing.

Jul 31, 2018

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Michel Rodrigo Luiz, Glaudistoni da Silva Félix, Osmar Duarte Junior

This article deals with a project to reduce the preparation time and threading the coils in the input section of a pickling line coupled to the cold strip mill (PLTCM) at ArcelorMittal Vega. The project developed serves for the detection and elimination of bottlenecks in the input section. The project was conceived by the philosophy of the Theory of Constraints (TOC) and Lean Six Sigma (6 sigma), here seen as sequencing serial / parallel in the preparation and threading the coils. In this context, a proposal to modify the automatic sequencing and reduction of interruptions due to failure of the automation / equipment confirmed its effectiveness reducing the total time preparation time and threading the coils in the entry section by 15%. This project was developed without investment costs, bringing gains on the order of US$613,769.00.

Oct 1, 2019

By Sihai Jiao, Xiaoming Xia, Bo Yan

Checkered plate, which is also known as floor plate, has a raised pattern that provides excellent skid resistance for a wide range of applications, such as flooring, walkways, platforms, stair treads, covers, etc. As one of most common products, carbon steel checkered plate is used in low strength with a large thickness margin for corrosion and costs a lot in corrosion resistance treatment and maintenance. Although austenitic stainless steel checkered plate meets the requirements of general corrosion resistance, it is also hard to provide a highly comprehensive performance for its low yield strength, which mean higher thickness, higher weight, lower stability of structure. Combined the advantages of stainless steel and carbon structural steel, a roll-bonded clad checkered plate with high performance in skid resistance, high strength and corrosion resistant is developed. The metallography shows metallurgically bonded interfaces. Both external and internal bending at room temperature can be done successfully done without any cracks. The yield strength is also significantly improved. Therefore, roll-bonded clad checkered plate is superior in microstructure, strength, ductility and workability. An application case on a pulverized coal injection platform in an iron-making plant, is also introduced to show the way of processing and installation. After two years of installation on the platform, the product still keeps the original appearance. It implies that the developed plate could keep the facilities functions with much less or no maintenance and make them much safer.

Oct 1, 2019

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Danilo Gonçalves de Oliveira, Rogério Martins Pereira

Chatter is a widely studied vibration phenomenon that affects most cold mills around the world and its impact on these lines are tremendous: from productivity and quality losses to mechanical equipment damage. The investigation of its origins and how to minimize the occurrences and their impact on the equipment require special instrumentation and algorithms in order to have a detection of the vibrations as soon as they start. This paper presents three methods of identification of chatter on a Tandem Cold Mill and the actions to leave the vibration frequency range before its amplitude achieve catastrophic values.

Oct 1, 2019

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Gabriel Oliveira Glória

Due to growing concern about the ambient impacts, lignocellulosic fibers are been investigated to replace the synthetic ones in polymer composites The giant bamboo fiber, a relatively unknown lignocellulosic fiber with potential for composite reinforcement, still needs to characterize for possible engineer applications. However the giant bamboo fiber has low adhesion with the polymeric matrix. In order to understand the interaction that occurs between the bamboo fiber and the polymer matrix is necessary to evaluate its physical and chemical characteristics. Therefore, the present work analyzed the giant bamboo fiber by means of Fourier Transform Infrared (FTIR) spectroscopy. The spectrum revealed main absorption bands typical of giant bamboo fiber specific molecular interactions.

Aug 16, 2017

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018