Search Documents

By Byron Johnston

IN 1926 I had occasion to make numerous measure-ments with a Pitot tube. The differential gage was mounted in a box, and since the work entailed setting upon girders, staging, and flues of various shapes and slopes, much time was generally expended in getting the box blocked into the level position. This inconvenience was so considerable that I devised the gage stand shown in the accompanying illustration. The gage is bolted to the board seat, the bolt per-mitting unlimited adjustment in the plane of the paper. The seat, carrying the gage, revolves on trunnions, per-mitting unlimited adjustment in a second plane, per-pendicular to the first. Consequently, the stand may be stood up, hung by one corner, leaned against some-thing or simply laid down, and the gage levelled from any position. On uneven surfaces, where the stand naturally rests on only three of its legs, it may be swung in the manner peculiar to the tripod, bringing the center of gravity within the triangle formed by the legs, thereby providing a firm set-up. Rubber stoppers under compression were found to give sufficient friction to hold the seat in the desired position.

Jan 3, 1928

Jan 1, 1966

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

THE vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.1 These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The major domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War II, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1947

By Ernest O. Kartinen

This report is the accumulation of eight years of experience on only one small phase in the business of oil production. It is not intended as a final report but rather as a progress report dealing with the internal corrosion of oil field dehydrating tanks. The corrosion of dehydrating tanks continues to be a problem in the production of crude oil. The deterioration hy corrosion of these tanks falls into three general classifications: (1) Atmospheric corrosion of exterior areas, (2) corrosion of the underside of deck and the rafters and top area of the upper row of staves in that part of the tank which is known as the vapor space, and (3) corrosion of the bottom and shell areas, and the steam coils which are normally immersed in water and thus exposed to the corrosive action of the water. Atmospheric corrosion is primarily a paint problem, and has been omitted in this discussion. The corrosion in the vapor space, in this company's experience, which has been of great concern only in one area. has also been omitted in this discussion. The third, and most troublesome type of corrosion, and the one with which this report deals, is that which occurs in the water-exposed areas of dehydrating tanks, and, to a lesser degree. in some stock tanks. The operating temperature of these waters varies from 80°F to 160°F and the salt counts run from a few thousand to as high as 25.000 parts per million. Corrosion in these tanks occurs in three forms: (1) pits, (2) ringworm type of attack along the vertical and horizontal bolt seams, and (3) as a general attack, spread over a wide area. Steam Coils In dehydrating tanks, our experience has been that the steam coils are the first to show signs of corrosion, and then the shell and bottom areas. This action is not uniform throughout this company's operations. Some installations have coil troubles with very little tank trouble, and some show just the opposite. But in the majority of cases the coils are the more seriously corroded areas. This may be partly due to the fact that we have tried by periodic application to keep a protective coating on the interior areas of the tanks, and some protection has been afforded by these coatings. Through the years several types of hot and cold coatings have been tried with many various methods of cleaning the steel, ranging from use of cleaning solvents to hot and cold Oakite washes, as well as sandblasting. Although experience has shown that a longer life expectancy of a coating is possible after a very thorough steel cleaning job, it has still been necessary to recoat these tanks at least every two or three years. Until a few years ago, vertical spiral steam coil bundles were installed when the tanks were originally erected. When these coils needed replacement, in some cases within 18 months, it was necessary to remove a couple of shell staves to accomplish this task. This required a down time period of several days and was often very inconvenient to the production operations of the leases. This problem was considered on the basis that the coils were expendable, and thus. to eliminate any unnecessary down time when changing coils, the vertical spiral coils were discarded in favor of horizontal flat coils which could be taken in and out of the tanks by way of the cleanout openings, and put together with unions. This made a fairly easily replaceable and repairable coil. But it was still very much of a nuisance when repairs were necessary. Efforts to increase the useful life of the dehydrating tanks led to the adoption of galvanized tanks at an increased initial cost. The zinc coating was depended upon for protection and no other protective coatings were applied. In July, 1944. during the development of a new lease, a 3-ring 1,500 bbl, black iron water tank was converted into a dehydrating tank with steam coils to handle the new production. This tank was coated inside with a cold, brushed-on coating, for protection against corrosion. After approximately 18 months of service, holes developed in the tank and the steam coils. The tank was emptied and cleaned for repairs. The coils were so badly pitted that it was felt advisable to replace them. Coating Becomes Loose Inspection of the tank showed the protective coating to be still in place but loose, and numerous blisters were in evidence. A closer inspection showed that the interior of this tank was so badly pitted under the coating that any further attempt to use the tank was inadvisable. This tank was therefore discarded and a new galvanized tank ordered and set up at considerable expense and inconvenience. In April, 1946, another dehydrating tank installation was made on an adjoining lease. This installation consisted of a 1,500 bbl. 3-ring galvanized tank with two sets of flat steam coils 12 in. and 24 in. up from the bottom. In September, 1947. seventeen months after installation. salt showed up in the boiler feed water. When the dehydrating tank was opened and cleaned, the steam coils were found to be badly pitted — several holes having penetrated through the wall of the pipe. New coils were installed.

Jan 1, 1950

By J. F. Gallie

From the standpoint of exploration and new discoveries, South Arkansas had a discouraging year in 1944. In January there were 73 untested drilling blocks, and 60 additions were made during the year. Of the total, 65 were condemned by dry holes on or adjacent to them, while 5 proved productive. The latter resulted in the discovery of the Salem Church, Calhoun Wilks, and Strong fields, and the extension of the Village field to the southeast. The year ended with 63 untested blocks, 41 of which were scheduled for tests to the Smackover lime, the state's deepest oil-producing formation. Geophysical activity in 1944 totaled 164 crew weeks, of which 110 were seismic, 43 gravity, and 11 radioactive (Fig. I), in contrast with 674 crew weeks reported for 1943, of, which 563 were seismic and in gravity, Five seismograph and two gravity crews were engaged in exploration in South Arkansas during January 1944. but only two seismograph crews were working there at the end of the year. In addition, exploratory core drills were used for a total of 38 weeks during the year. The year's few discoveries, none of which is considered as having added appreciably to state reserves, were the meager results obtained in the drilling of 62 wildcat wells 2000 ft. or deeper. Of this total (a detail of which appears in Table 2), 42 were drilled to the Smack-over lime or below, The average depth of the 62 wells was 5384 ft., as compared with 4992 ft. in the preceding year, while the average depth of the 42 wildcats in the lime was 5913 ft. in 1944. Fig. 2 has been prepared to show all , wells penetrating to the Reynolds oölitic lime. The 1944 dry holes are circled lightly, while discoveries are heavily circled and shown as producers. Smackover lime fields, producing from the Reynolds oolitic lime member, are indicated in black, and the locations of dry wildcat wells drilled prior to 1944 are also shown. Table 3 provides a listing of all Smackover lime wells drilled through the end of 1944. Production for the year was slightly more than in 1943, totaling 29,282,747 bbl., as compared with 27,521,943 bbl. for the preceding year. The increase was 1,760,804 bbl., or 6.4 per cent, bringing production to a peak exceeded only in the 1923 to 1928 period of flush production from the older shallow fields, principally Smackover. The increase was largely attributable to additional development in the Dorcheat-Macedonia, Atlanta, Fouke, Stephens-Smart, Haynesville, and Village fields, little production deriving from 1944 discoveries. These six fields accounted for loo of the 122 field wells drilled during the year. Annual and cumulative production for the producing life of the state are presented graphically in Fig. 3. Fig. 6 has been prepared by the author to show the producing ages and present known productive limits of all fields in South Arkansas. Production data, as usual, are assembled in Table 2, and provide a further breakdown of producing formations in the individual fields.

Jan 1, 1945

By R. Gilman Brown

Mines are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique gcological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.' On the other hand, this output has beeu mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness from 0.5 in. of ('specimen rock" to 30 ft, of clay and quartz; distributed through a zone about 2,000 ft, in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a

Jan 1, 1908

By R. P. Dolan, W. M. Shedd, B. L. Buchanan

Analytical expressions are derived from empirical data relating the basic physical device parameters to the radiation dose. To put in perspective and justify the approach taken, the overall problem and methods of attempted solution of radiation damage to transistors in a missile or satellite environment is briefly examined. The main emphasis is on a new criteria for neutron radiation hardness and the device design implications resulting from using this criteria. Contrary to other derived criteria, the derived bipolar hardness relation depends mainly on the initial lifetime rather than the base transit time. It is shown, that contrary to previously accepted beliefs, the inherent attainable radiation tolerance of JFET's is at least a factor of ten greater than the radiation tolerance ofbipolars. Experimental results on JFET's designed for maximum neutron radiation tolerance are presented. The accuracy, utility, and range of possible validity of various published lifetime and carrier removal damage constants are discussed. It is well known that transistors are subject to damage due to radiation at much lower radiation levels than those which would cause structural damage to a missile or satellite. The three principal categories of radiation damage to transistors are displacement, ionization, and thermomechanical. The main cause of displacement damage is fast neutrons, and the main effects which permanently degrade transistor operation are minority carrier lifetime reduction and carrier removal. A second-order effect is mobility reduction. The main cause of ionization damage is gamma radiation which results in permanent effects due to charge build-up in the oxide and transient effects due to photo-current generation. The transient effects are usually handled by using circumvention techniques in the electronics system. The extent of the transistor degradation due to displacement and ionization damage depends strongly on the transistor type, whereas the extent of thermomechanical damage does not depend on the transistor type, but depends mainly on packaging and metallization which are common to all transistor types. The standard transistor types are categorized in Fig. 1 and typical cross-sections are shown in Fig. 2. The original reason for the designation of the two classes of transistors was that the unipolar operation depends on only one carrier (majority) and the bipolar operation depends on both minority and majority car- riers. The bipolar is then seriously degraded by minority carrier lifetime reduction, whereas the unipolar or field effect transistor is not. One of the two principle classes of field effect transistors, the junction field effect transistor (JFET), depends strongly on carrier removal. However, the insulated gate (MIS) is little affected by either carrier removal or lifetime changes, but is virtually eliminated as a radiation resistant device because of permanent charge build-up in the insulator caused by ionizing radiation. The bipolar and JFET suffer only minor effects due to charge build-up in the oxide passivation when compared1 to the MOS. This is because the active region of the MOS is adjacent to or part of the oxide layer. It is then the bipolar and JFET which are potentially resistant to permanent radiation damage. DERIVATION OF RADIATION TOLERANCE RELATIONS Criteria. The bipolar is by far the most widely used transistor type. The usual criteria for hardening bipo-

Jan 1, 1970

In the maintenance of rubber-tired mining equipment, tires may well represent the single greatest problem. Using a 50-ton truck as an example, engine upkeep averages about 8% of the machine's total yearly operating cost, while tires average a whopping 20%. In fact, depending upon such factors as job layout, conditions, and whether it is maintenance or production people who run the job, tire costs can climb to as high as 50% of the truck's total operating expense. Similar costs apply to other earthmoving equipment such as tractor-scrapers and front end loaders. While operators must resign themselves to "normal" tire life and wear, there are many corrective steps that can be taken to fight the "abnormal."

Jan 8, 1978

Jan 1, 1970

By C. A. Winkler, V. Hospadaruk

PREVIOUS papers from this laboratory have discussed the effect of chloride ion on the cathode polarization during electrodeposition of copper from copper sulphate-sulphuric acid electrolytes, in the presence and absence of gelatin. The steady state polarization'" was found to decrease sharply and pass through a minimum with increasing chloride ion concentration in the presence of gelatin. The minimum shifted to higher chloride ion concentrations and to higher polarization values with increase in current density or gelatin concentration, while an increase of temperature shifted the minimum toward lower halide concentrations and lower polarizations. Since these observations were made in acid-copper sulphate electrolytes that contained no other addend than gelatin, there was obviously the possibility that they were not applicable to deposition of copper from commercial electrolytes that contain a variety of other substances in relatively small amounts. In particular, it was of interest to determine whether the presence of arsenic, antimony, or bismuth in the electrolyte would materially alter the behavior. Experiments have now been made under a variety of conditions with systems containing these cations, and the results are summarized in the present paper. Experimental Polarization measurements were made at 24.5oC in a Haring cell in the manner described previously.' Electrolytes were made with doubly-distilled water, and contained 125 g per liter of copper sulphate and 100 g per liter sulphuric acid, both of reagent grade Eimer and Amend gelatin from a single stock was used throughout. Chloride ion was introduced as reagent grade sodium chloride, and arsenic, antimony, and bismuth by dissolving the chemically pure metal in hot concentrated sulphuric acid and adding appropriate amounts of the solutions to the electrolyte. Each cathode, of 1/16-in. thick rolled copper, was first etched in 40 pct nitric acid and washed thoroughly with distilled water. The surface was then brought to a standard condition4~9 by electrodeposition from an acid-copper sulphate electrolyte containing no gelatin, at a current density of 3 amp per sq dm for 30 min, followed by deposition at a current density of 2 amp per sq dm for l hr. As in previous studies, the cathode polarization eventually attained a steady-state value (15 to 75 min) such that further change in polarization did not exceed 0.2 mv per min. The polarization values recorded are those for the steady states. "Excess weights" were determined with arsenic and antimony present in the electrolyte, as the difference between the weights of the deposits obtained in the presence of these cations and those obtained in their absence, with the two cells connected in series. When gelatin was present along with the arsenic or antimony, it was also added to the electrolyte in the cell in series. Results and Discussion The results of the study are summarized in Figs. 1 to 6. From Fig. 1, top, it is evident that the presence of arsenic or antimony alone results in an increase of polarization, while bismuth alone causes a decrease. The presence of gelatin (25 mg per liter) rather drastically modifies all three cation effects, as indicated in the lower panels of the same figure. The addition of chloride ion, when no gelatin is present, causes comparable decreases in polarization in the presence of antimony and bismuth, but a relatively larger decrease when the electrolyte contains arsenic. It is interesting to note that the decrease in polarization brought about by addition of chloride when both arsenic and antimony are present parallels the behavior with arsenic alone, while the polarization in the electrolyte containing the cation mixture, without chloride added, corresponds to that for an electrolyte containing only the antimony cation. Similarly, the polarization at zero concentration of chloride in electrolyte containing arsenic and bismuth is that corresponding to an electrolyte containing arsenic alone. From Figs. 3a, 4a and 4b, it is clear that, in the presence of gelatin at a level of 25 mg per liter, the effect of chloride in the presence of arsenic and antimony, or a mixture of the two, becomes quite analogous to that observed in the absence of added cations. When both bismuth and gelatin are present (Fig. 5), the decrease in polarization with increased chloride concentration is virtually absent. This is perhaps a reflection of the large decrease in polarization brought about by the bismuth itself in the presence of gelatin. The shifts of the minimum in the polarization-chloride concentration curves brought about by changes of temperature (Fig. 3b), gelatin concentration (Figs. 3c and 4c) and current density (Fig. 3d) when the metal cations were present are all similar to the corresponding shifts observed in their absence." The approximately linear "excess weightv-anti-mony concentration relation recorded in Fig. 6 would seem to indicate that antimony is codeposited with copper to a considerable extent. On the other hand, only very limited amounts of arsenic appear to be adsorbed or codeposited.

Jan 1, 1954

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By D. J. Varnes

Rocks in mines, quarries, and many outcrops commonly show evidence of being under high stress. Saw cuts and drillholes close in, partly mined coal bursts violently, and pillars crush and rock spalls in mines even at moderate depths. Similarly, strong and massive rocks such as granite and sandstone naturally divide themselves into sheets that lie more or less parallel to their outward topographic form. The sheets may be either convex or concave. Thin plates of bare rock surfaces bow up and buckle. Such effects often cannot be explained by the obvious loads now acting on the rock, that is, by loads resulting from overburden, topographic irregularities, or stress concentration around openings. The stresses exceed those that would result from such loads. Two interpretations of such excess stresses have been made. In one, the stresses are assigned in origin to now active tectonic forces. In the other, they are regarded as leftover and locked in from some previous state at which higher pressures prevailed. These two sources may both operate and they generally cannot be distinguished easily in the field. There are other complicating sources of stress such as temperature gradients and chemical alteration. Nevertheless, some bodies of rock, by exfoliating, show evidence of high internal stress even though they are practically unweathered and so isolated topographically that the presence in them of significant stress due to exterior loads or active tectonic forces seems unlikely (Fig. 1). Moreover, completely isolated rocks are known to change density, shape, or size 1,2 to expand under constant compressive stress;3 and even to disintegrate 4,5 without the intervention of weathering processes. The stresses involved here must be truly residual in the sense long used by metallurgists; that is, residual stresses in a body are those that remain.

Jan 1, 1970

Jan 1, 1969

Jan 1, 1967

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The authors give a definition of the various types of corrosion that may affect a metallic conductor buried in the ground, namely: 1. The metallic conductor may be attacked by the surrounding soil. This phenomenon is purely local and is called by them soil corrosiveness. 2. The metallic conductor may connect two regions of the ground when the electrolytes have a different composition. An electrical current will then be generated and certain zones of the conductor will be oxidized. This is autogalvanic corrosion. 3. Stray current may flow in the ground and enter the conductor in certain sections and leave it in others, thus causing oxidization in certain zones; this is electrolytic corrosion. The soil corrosiveness has been studied extensively by the United States Bureau of Standards and the authors give a summary of the work carried out and results obtained along this line. In autogalvanic corrosion it has been shown, by the investigation of buried pipes, that the zones of corrosion are associated with the zones of egress of the electric current (anodic zones). The location of these zones can be determined by measuring at the surface of the ground the difference of potential that exists along the path of the pipe. This work is performed easily and quickly with the apparatus invented by the authors for the exploration of conductive orebodies. The problem of electrolytic corrosion is a difficult one because it is a question of stray current which may vary in direction and intemsity at every instant. Therefore the components of the electrical field must be known at a given station and compared with the components of the clectrical field at another station, at the same moment. This is achieved by a rccording apparatus that will register the variations of the intensity of the electrlc current along two rectangular directions, during several minutes

Jan 1, 1934

By C. K. Leith, W. J. Mead

In 1911, we published in the Transactions a brief account of the lateritic alterations of serpentine in eastern Cuba, producing the important iron-ore deposits of the Mayari and Moa districts.' The special feature of that article was a quantitative treatment of the alterations, based on analyses, to show just what had happened in terms of chemical, mineralogical, and physical changes. Professor Kemp has published an interesting account of these ores, containing additional quantitative observations of his own, tending essentially to confirm the nature of the changes that had been worked out.2 His discussion suggests to us the desirability of publishing certain additional quantitative data which were not included in our previous article. This seems especially desirable because quantitative measurements of lateritic alterations are rare, and this particular case may be regarded as typical of a fairly wide range of alterations of this kind. At the time of our examination of Mayari and Moa deposits 29 complete analyses were supplied us by the chemists of the Spanish-American Iron, Co., representing a graded series from the unaltered serpentine rock below to the ore at the surface. These analyses are given in the accompanying table. The mineralogical composition of the ores and rocks is comparatively simple and can be easily calculated from the analyses. In Fig. 1 the mineralogical changes from the serpentine rock below to the lateritic iron ore above, based on the analyses, are expressed in terms of weight, assuming alumina to have remained constant during the alteration. It is not easy by mere inspection of this table of analyses to determine what the progressive chemical changes have been in development of the ore. In order to bring this out clearly, the analyses have been graphically represented in Fig. 2 in such a fashion as to show the progressive additions and losses of substances during alteration.

Jan 1, 1916

Scraper and Slide Riddell Mucker Boskovich Device Hydro-mucker Inclined Shaft Mucking The Benching Method Performance Chart

Jan 3, 1950